Harman Kardon Citation II Assembly And Operation Manual page 26

Check TB1 TB2
( ) ( ) ( )
1K mmf or .001 mfd capacitor (value marked on body of capacitor) from TB1-41 (S) to TB1-
24 (S).
( ) ( ) ( )
12K ohm 5 watt resistor (value marked on body of resistor) from TB1-11 (S) to TBl-25 (S).
Mount
( ) ( ) ( )
4.7K ohm 3 watt resistor (value marked on body of resistor) from TB1-10 (S) to TBl-26 (S).
Mount
( ) ( ) ( )
1 meg ohm
( ) ( ) ( )
6.8K ohm
( ) ( ) ( )
150 mmf capacitor (value marked on body of capacitor) from TB1-8 (S) to TB1-39 (NS).
( ) ( ) ( )
220 ohm
( ) ( ) ( )
1 meg ohm
( ) ( ) ( )
20 mmf capacitor (value marked on body of capacitor) from TBl-38 (S) to TB1-7 (S).
( ) ( ) ( )
680K ohm 1 watt 10% resistor (blue-gray-yellow-silver) from TB1-6 (NS) to TBl-37 (NS).
( ) ( ) ( )
4.7 mmf condenser (value marked on body of capacitor) from TB1-6 (S) to TB1-37 (S).
( ) ( ) ( )
220 ohm 12 watt 10% resistor (red-red-brown-silver) from TB1-5 (S) to TB1-36 (NS).
( ) ( ) ( )
1 meg ohm
( ) ( ) ( )
5K ohm 7 watt resistor (value marked on body of resistor) from TB1-4 (S) to TB1-31 (S).
Mount
space provided to the left of the lugs.
( ) ( ) ( )
22K ohm 3 watt resistor (value marked on body of resistor) from TB1-3 (S) to TBl-32 (S).
Mount
( ) ( ) ( )
8.2K ohm 2 watt 10 % resistor (gray-red-red-silver) from TB 1-2 (S) to TB 1-33 (S). Mount
⅜
˝ off terminal board as shown in Figure N.
( ) ( ) ( )
100K ohm resistor
THIS COMPLETES THE ELECTRICAL ASSEMBLY OF THE AMPLIFIER KIT. Do not install the
tubes or connect the amplifier to an AC outlet until you have read the paragraph on final inspection.
⅜
˝ off terminal board as shown in Figure N.
⅜
˝ off terminal board as shown in Figure N.
½
watt 10% resistor (brown-black-green-silver) from TB1-40 (S) to TBl-27 (S).
½
watt 10% resistor (blue-gray-red-silver) from TB1-8 (NS) to TB1-39 (NS).
½
watt 10% resistor (red-red-brown-silver) from TB1-39 (S) to TB1-28 (S).
½
watt 10% resistor (brown-black-green-silver) from TB1-7 (NS) to TBl-38 (NS).
½
watt 10% resistor (brown-black-green-silver) from TBl-36 (S) to TB1-30 (S).
⅜
˝ off terminal board as shown in Figure N. Position the body of this resistor in the
⅜
˝ off terminal board as shown in Figure N.
½
watt 10% (brown-black-yellow-silver) from TB1-1 (S) to TB1-35 (S).
24