Table of Contents Important Safety Information ...4 Introduction...6 Description ...6 Unpacking and Installation ...7 Rear Panel Connections ...8 Power Control Connections ...9 Channel Configurations ...11 System Connections ...12 Input and Bridging Connections...13 Speaker Wire Preparation and Connection...17 Operation...19 Service Information ...20 Troubleshooting Guide...21 Specifications...22 Madrigal Audio Laboratories...
Important Safety Information Verify Line Voltage Before Use Your new Citation 5.1 amplifier has been factory configured for a specific line volt- age: 110-120 volts for North America or 220-240 volts in most other countries. Connecting the amplifier to a line voltage other than that for which it is intended can create a safety and fire hazard, and may damage the amplifier.
Remember, the Citation 5.1 weighs over 60 pounds. • High powered audio amplifiers such as the Citation 5.1 may develop moderate amounts of heat. Therefore, if the unit is installed in a cabinet it is recommended that the rear of the cabinet be left open to permit air circulation.
5.1 Amplifier Description The Citation 5.1 is a flexible, state of the art audio power amplifier designed to deliver high performance in a variety of applications. Each of the four amplification channels has a separate power supply, which means that it delivers audiophile per- formance no matter which configuration is selected.
Packing materials that cannot be collapsed should be saved along with the carton in a plastic bag. In order to assure a high level of performance and long life, the Citation 5.1 has been engineered from robust materials. This weight, however, requires, that you pay special attention to unpacking and installation of the unit.
Rear Panel Connections Bridged/Normal Switches: These switches control the output configuration of a pair of channels. Switch them down for normal use. Switch them down to “bridged” to combine amplifier channels for higher power output. See page 13 for more information on channel configuration and bridging. Power Switch: This is the master AC power switch for the unit.
Power Control Connections The Citation 5.1 amplifier features a built-in system that will automatically turn on the amplifier when another device in the system is switched on. To activate this system, the 5.1 must be used in conjunction with a Citation Surround Controller or Processor, other Citation Power Amplifiers, and other approved devices.
Page 10
If this is the only remote controlled amplifier in the system, no further connections are needed. If multiple remote controlled amplifiers are used, connect the “Remote DC OUT” jack on one amplifier to the “Remote DC IN” on the next unit in the system.
Two-Channel Operation The immense power capability of the Citation 5.1 allows it to be used in a dual bridged mode as a conventional stereo amplifier. For critical music listening, this will permit you to drive virtually any full range speaker in the largest home acousti- cal and physical space, delivering classic two-channel stereo sound at its finest.
Note: When making connections between any source components or proces- sors or preamplifiers and the Citation 5.1, or when making any connections to speakers, be certain that both the input device and the amplifier are turned off. To assure that there will be no unwanted signal transients that can damage equipment or speakers, it is always best to unplug all equipment before making any connections.
CH 1 INPUT CH 2 INPUT MODE TURN ON (BRIDGED INPUT) (NOT USED IN BRIDGED MODE) – BRIDGED – – BRIDGED Citation 5.1 CH 1 OUTPUT CH 2 OUTPUT Amplifier – NORMAL MANUAL MODE TURN ON BRIDGED REMOTE CH 1 INPUT...
Page 14
Connect the output from your processor or preamp which is to be connected to the higher powered amplification channel (center or subwoofer channels) to the input connector marked “Channel Three” on the rear of the Citation 5.1. The input connection for “Channel Four” is not used in this configuration. (Figure 2B)
Page 15
TO PROCESSOR NORMAL MANUAL MODE TURN ON BRIDGED REMOTE CH 1 INPUT CH 2 INPUT MODE TURN ON (BRIDGED INPUT) (NOT USED IN BRIDGED MODE) – BRIDGED – – BRIDGED CH 1 OUTPUT CH 2 OUTPUT – – Note: Switch on left (ch. 1 & ch. 2) is in the “Up” or “Normal” position. Switch on the right (ch.
Page 16
TO PROCESSOR NORMAL MANUAL MODE TURN ON BRIDGED REMOTE CH 1 INPUT CH 2 INPUT MODE TURN ON (BRIDGED INPUT) (NOT USED IN BRIDGED MODE) – BRIDGED – – BRIDGED CH 1 OUTPUT CH 2 OUTPUT – Note: Both switches should point Down to the “Bridged” position. Figure 2C For two-channel use, make certain that BOTH bridging switches are engaged by switching them down, to the “bridged”...
Speaker Wire Preparation and Connection Once the proper hookup has been selected using the previous section, make the physical connection using the following instructions. Cables or Connecting Wire To assure that the high quality signals produced by your Citation amplifier are car- ried to your speakers without loss of clarity or resolution, we recommend that you use high quality speaker cable.
Page 18
icons next to each pair of terminal posts will guide you to the correct connections. When the connections are made, twist the cap back so that the connection is secured, but do not overtighten or use tools, as this may break the delicate wire strands and decrease system performance.
Operation Operation of the Citation 5.1 is simple. There are no controls to adjust once the installation is complete. After all connections have been made to the amplifier’s inputs and speaker termi- nals, connect the AC power cord to the socket on the rear panel. Make certain that the master power switch on the rear panel is in the OFF position.
Fuse The Citation 5.1 uses internal fuses to protect both it and your speakers from dam- age. In the event that a fuse replacement is required, make certain that a fuse of the original rating is used.
Troubleshooting Guide The Citation 5.1 is designed for trouble free operation. In normal use, most users will not encounter any problems with the unit. However, as with any sophisticated electronic device, there may be occasional problems on initial installation, or during the life of the unit.
Specifications Power Output: HCC: Frequency Response: THD/IMD: Power Bandwidth: Input Impedance: Input Sensitivity: Control Trigger Voltage: Dimensions (HxWxD): Weight: Power Requirements: Dual Drive is a trademark of Harman Kardon, Inc. Dolby and Pro Logic are registered trademarks of Dolby Laboratories Licensing Corp. THX is a registered trademark of Lucasfiilm Ltd.
Page 23
Staple or clip original invoice here. M...