Table of Contents
Related Manuals for Super Circuits SY30304
Summary of Contents for Super Circuits SY30304
- Page 1 SY303 Series Video Camera Systems Products: SY30304, SY30308, SY30316 Please read this manual before installing and using this system, and always follow instructions for proper use. Please save this manual for future reference. SY303xx_SI...
-
Page 2: Legal Notice
WARNING RISK OF ELECTRIC SHOCK. DO NOT OPEN. To reduce the risk of electric shock, do not remove the cover (or back). No user serviceable parts exist inside. Refer servicing to qualified service personnel. To reduce the risk of fire and electrical shock, do not expose any product to rain or moisture unless it is designated as weatherproof. -
Page 3: Table Of Contents
TABLE OF CONTENTS Table of Contents SECTION 1 Getting Started: Unpacking Your System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 1 .1 Unpacking the equipment . -
Page 4: Section 1 Getting Started: Unpacking Your System
SECTION 1: GETTING STARTED SECTION 1 Getting Started: Unpacking Your System For most installations, Supercircuits video systems come with everything needed to install and operate your video surveillance system. If your system uses multiple power supplies, you may also need multi- outlet power strips. -
Page 5: Section 2 Equipment Testing
SECTION 2: EQUIPMENT TESTING SECTION 2 Equipment Testing Due to the sensitivity of electronic devices and the potential for damage during shipment, it is important to bench test each component of the system before installation. Equipment testing is performed in two stages: Camera testing by attaching it directly to a monitor •... -
Page 6: Camera Testing With The Monitor
SECTION 2: EQUIPMENT TESTING Attach the camera drop cable to the BNC to BNC cable. To attach the BNC connector, push the cable BNC connector onto the camera’s BNC connector and twist the outer barrel until it locks into place. Video Camera Monitor Connect... -
Page 7: Camera And Dvr Testing
SECTION 2: EQUIPMENT TESTING 10. Unplug the camera’s power adapter from its power source. 11. Repeat this test using every camera, cable, and power adapter you will use to install your system. 2.2 Camera and DVR testing Unpack the DVR. Use the VGA cable provided with the monitor to connect the VGA port on the back of the DVR to the VGA port on the underside of the monitor. - Page 8 SECTION 2: EQUIPMENT TESTING Monitor VIDEO IN Connect Connect Power Adapter For Camera Typical bench test connection of a camera and a DVR Plug the camera power adapters into a power source to power the cameras on. Use the DVR front panel controls to select each camera individually. Verify that the monitor displays a clear image from each camera.
-
Page 9: Section 3 Installation Tips
SECTION 3: INSTALLATION TIPS SECTION 3 Installation Tips 3.1 Camera placement Use the information included in the packaging of your camera to mount and connect the unit to power and video cables. Plan your camera installation carefully. Identify the locations where cameras will provide the best coverage, considering: Field of view –... -
Page 10: Dvr/Recorder Placement
SECTION 3: INSTALLATION TIPS A 100' BNC video/power cable is shipped with every camera in your system. Custom-cut cables are also available from Supercircuits. 3.4 DVR/recorder placement Your recording equipment is central to the accurate capture of video evidence and constant surveillance. Supercircuits strongly suggests that it be installed in a secure location with access limited to authorized personnel. -
Page 11: Section 4 Device Inter-Connection Diagrams
SECTION 4: DEVICE INTER-CONNECTION DIAGRAMS SECTION 4 Device Inter-Connection Diagrams A typical cabling diagram for 4, 8 or 16 camera systems. Monitor (Digital Video Recorder) Video Cameras Video Cameras Typical cabling diagram for 4, 8 or 16 camera systems SY303 Series Video Camera Systems... -
Page 12: Section 5 Troubleshooting Faq
SECTION 5: TROUBLESHOOTING FAQ SECTION 5 Troubleshooting FAQ IQinstalledQtheQcablesQtoQmyQvideoQequipment,QbutQtheQpowerQplugQ won’tQfitQintoQtheQcameraQorQtheQpowerQadapter: Chances are you’ve run the cable backwards. Only one end of the camera cables supplied by Supercircuits will fit the camera, while only the other end will fit the power adapter.
Need help?
Do you have a question about the SY30304 and is the answer not in the manual?
Questions and answers