SAFETY INSTRUCTIONS Read operator’s manual. Be thoroughly familiar with the controls, capabilities, and proper use of the equipment. NEVER ALLOW ANY RIDERS. IMPORTANT: This cab must only be used on units outfitted with a FOLDING ROPS (Roll Bar). DO NOT place this cab on a unit with a non-folding ROPS. DO NOT remove the top half of the folding ROPS to accommodate this cab.
Page 3
Cab Installation 2.1) Pull roll bar pins and tip upper roll bar section down. 2.2) Tilt steering column towards seat. 2.3) Tip-up seat towards steering column. 2.4) Open engine cover –Some may choose to remove engine cover and set cover aside. 2.5) From the rear side of the tractor, there are 4 bolts that secure a mount plate to the roll bar.
Page 4
Cab Installation (Continued) CAB SETS OVER CAB ADAPTER PLATES ELECTRICAL WIRE HEATER HOSES CAB ADAPTER PLATES FIGURE 2-8 2.9) Secure cab with (2) 3/8” bolts, (4) 3/8”flat washers and (2) 3/8” nylock nuts (Refer to items 1, 2, 3 and 4 on mount kit drawing 4-14563). See figure 2-9. FASTENER ITEMS 1, 2 AND 4 ITEM 3 FIGURE 2-9...
Page 5
Cab Installation (Continued) 2.10) From inside the cab, there are four holes located on the cab floor, used for securing the cab to the frame of your unit. Match-Drill the holes, using a 7/16” diameter drill bit. Verify there are no obstructions on the underside of the unit’s frame. Secure the floor of the cab to the unit using 4 bolts, 8 flat washers and 4 nylock nuts 2.11) (Items 1, 2 and 4 on mount kit drawing 4-14563).
ELECTRICAL MOUNTING 3.1) Disconnect battery. 3.2) The cab is supplied from the factory, pre-wired. Locate the 12 Gauge red wire that runs down the right rear cab frame tube. 3.3) With the engine hood opened, route the wire to the right inside area of the engine compartment.
Page 7
3.8) The red wire from the cab hooks attaches to pin number 87 on the black relay. 3.9) The red wire from the silver breaker switch hooks to the positive side of the starter post. (See figure 3-9). RED 12 GA WIRE FROM RIGHT REAR CAB FRAME TO RELAY PIN 87 WIRE ASSEMBLY HARNESS -3...
Page 8
HEATER HOOKUP INSTRUCTIONS Pressure/Hot Line to cab heater core; 4.1) With the engine hood opened, drain the radiator by opening the radiator drain plug. 4.2) The pressure-hot hose will be hooked up with the aluminum fitting, one brass fitting, O-ring washer and a 5/8” hose clamp (Items 8, 11, 12 and 13 on mount kit drawing 4-14563).
Page 9
Return Line -from cab heater: 4.8) The return line will be hooked up using a hose-T, two 1-1/4” hose clamps and one brass fitting (Items 10, 11, 12 and 9 on mount kit drawing 4-14563). 4.9) Select the radiator hose that runs from the radiator to the water pump. Unclamp the hose at the radiator and remove an internal hose spring if the unit has one inside this hose.
Page 10
ROTARY BRUSH ANTI-KICKBACK STOPS FOR COZY CAB A-11241 and JOHN DEERE 1400 TRACTORS WITH ROTARY BRUSH ATTACHMENTS. A. Even though the rota ry brush frame appears to have clearance when raised all the way up, the lin kage of the REMOVE assembly could allow the boom of th e rotary brush to bo unce therefore,...
Page 11
ADDENDUM_05-10386a INSTALLATION ADDENDUM John Deere 1400-1500 Series 2 Heater Hook-Up Kit 8-14856 DATE: 8-23-04 FOR COZY CAB A-11241 and JOHN DEERE 1400-1500 Front mount tractors, SERIES 2 MODELS Manufacturers have been known to change engines, water pumps, alternators and other components to improve performance of their product at anytime.
Page 12
ADDENDUM_05-10386-b Seat Seal Kit 4-14915 and Addendum Notes John Deere 1400-1500 Series 2 DATE: 1-10-05 (1) 3-10607 x 4” LG FOR COZY CAB A-11241 and JOHN DEERE 1400-1500 Front mount tractors, SERIES 2 MODELS B1. Electrical wiring revision; In step 3.10 of the mounting instruction manual states connecting the blue wire from the wire relay harness to a brown connector located under the seat.
Page 13
ADDENDUM_05-10386-b Seat Seal Kit 4-14915 and Addendum Notes John Deere 1400-1500 Series 2 (1) 3-15279 x 24” LG (1) 3-10610 x 3” LG (1) 3-18829 x 24” LG Figure 5 (1) 3-15279 x 24” LG Figure 6 (2) 3-17865 x 6” LG (each side) Figure 7 Any you have questions or comments, feel free to contact us...