Related Manuals for Just Add Power Cardware VBS-PTP-308B
Summary of Contents for Just Add Power Cardware VBS-PTP-308B
-
Page 1: Installation Guide
Worship Center Broadcast System Installation Guide Just Add Power Cardware Company www.justaddpower.com support@justaddpower.com Copyright 2008, Just Add Power Cardware Co., Inc. All Rights Reserved. Page 1 of 28... -
Page 2: Table Of Contents
Group Port Setting ............................ 23 Video Scaler Resolution setting........................ 23 Basic Trouble Shooting Techniques ......................25 Example Diagnostic Procedures ........................25 Specific Problem Diagnosis .......................... 26 Copyright 2008, Just Add Power Cardware Co., Inc. All Rights Reserved. Page 2 of 28... -
Page 3: Introduction
Broadcast Audio/Video to Group • • Software based RS232 Remote Control Independent Rear Projector Output • • All functions delivered over CAT5e cable Matrix output (audio/video are independent) Copyright 2008, Just Add Power Cardware Co., Inc. All Rights Reserved. Page 3 of 28... -
Page 4: System Components
Guiding Light Keyboard VBS-SLK-4502 Projector Connector Transmitter/Receivers Video Genie Video Genie Projector Connector Extended Receiver Total Control Console Guiding Light Keyboard Projector Connector Dual Monitor Receiver Copyright 2008, Just Add Power Cardware Co., Inc. All Rights Reserved. Page 4 of 28... -
Page 5: Installation Procedure
VGA Output of the announcements PC to the port labeled VGA. This VGA signal will be displayed on the attached monitor/projector when the WCBS is not controlling the output device. Copyright 2008, Just Add Power Cardware Co., Inc. All Rights Reserved. Page 5 of 28... -
Page 6: Connect Receivers To The Video Genie™ Bus Ports
Connect up to 4 Video Devices to the Video Genie Scaler using standard video cables. Optional: Connect a composite video monitor to the A/V OUT port for A/V preview functions. Copyright 2008, Just Add Power Cardware Co., Inc. All Rights Reserved. Page 6 of 28... - Page 7 20. Optional: Connect a microphone to the MIC port if you want to be able to talk to the remote viewing locations with a microphone in the booth. Copyright 2008, Just Add Power Cardware Co., Inc. All Rights Reserved. Page 7 of 28...
-
Page 8: Worship Center Broadcast System Software Installation And Configuration
“Next” button to continue. The Customer Information screen should appear. Please input your User Name and Organization, and then click on the “Next” button to continue. Copyright 2008, Just Add Power Cardware Co., Inc. All Rights Reserved. Page 8 of 28... - Page 9 Simply click on the “Next” button to continue. The Installation Completed screen should appear. Now click on the “Finish” button to exit the installation Wizard. Copyright 2008, Just Add Power Cardware Co., Inc. All Rights Reserved. Page 9 of 28...
-
Page 10: Of 3 Install The Hotkeys Utility Program
Keyboard is set to have the operator press the CTRL key and the WINDOWS key at the same time, and while holding them down, press one of the designated F keys. Copyright 2008, Just Add Power Cardware Co., Inc. All Rights Reserved. Page 10 of 28... -
Page 11: Of 3 Customize The Worship Center Broadcast System Graphical User Interface
Keyboard (or any other PC keyboard) to control the system with the Hotkeys program, you should enable this function. Otherwise disable hotkeys to cut down on the PC overhead associated with the system. Copyright 2008, Just Add Power Cardware Co., Inc. All Rights Reserved. Page 11 of 28... -
Page 12: Change Messages
The Delay Timer settings should only be changed when Just Add Power support has identified a problem with screen transitions on the customer projection system. This will give a longer black screen time between transitions. Copyright 2008, Just Add Power Cardware Co., Inc. All Rights Reserved. Page 12 of 28... -
Page 13: Ir Learning Mode
Keep repeating this process to learn additional commands, or click on RESET to get out of IR Learning Mode. Copyright 2008, Just Add Power Cardware Co., Inc. All Rights Reserved. Page 13 of 28... -
Page 14: Worship Center Broadcast System Operation
PC1 VGA This will put the signal from PC1-VGA on the target monitor/projector. PC2 VGA This will put the signal from PC2-VGA on the target monitor/projector. Copyright 2008, Just Add Power Cardware Co., Inc. All Rights Reserved. Page 14 of 28... -
Page 15: Control Buttons
IR device while the other AV device is still active. For example, you could use this function to queue a DVD player while the Video Camera is still being broadcast. Copyright 2008, Just Add Power Cardware Co., Inc. All Rights Reserved. Page 15 of 28... -
Page 16: Rs232 Remote Control
Baud – enter the number correctly or things won’t work! Parity – valid inputs are “n” for NONE, “e” for “EVEN”, and “o” for ODD Length – typically 7, 8, or 9 Copyright 2008, Just Add Power Cardware Co., Inc. All Rights Reserved. Page 16 of 28... - Page 17 Parity – valid inputs are “n ” for NONE, “e” for “EVEN”, and “o” for ODD Length – typically 7, 8, or 9 Stop Bit – typically 1 or 0 Copyright 2008, Just Add Power Cardware Co., Inc. All Rights Reserved. Page 17 of 28...
- Page 18 COM Port – you can assign a different Com port to each command. Copyright 2008, Just Add Power Cardware Co., Inc. All Rights Reserved. Page 18 of 28...
-
Page 19: Total Control Console Basic Operation
Preview Video2 on LCD Press [LCD] [Video2] • Press Preview Video3 on LCD Press [LCD] [Video3] • Press Preview Video4 on LCD Press [LCD] [Video4] Copyright 2008, Just Add Power Cardware Co., Inc. All Rights Reserved. Page 19 of 28... - Page 20 Show Video2 on Projector Press [Projector] [Video2] • Press Show Video3 on Projector Press [Projector] [Video3] Show Video4 on Projector Press [Projector] • Pre ss [Video4] Copyright 2008, Just Add Power Cardware Co., Inc. All Rights Reserved. Page 20 of 28...
- Page 21 [Group B] [Video2] • Press Broadcast Video3 to Group B Press [Group B] [Video3] • Pre ss Broadcast Video4 to Group B Press [Group B] [Video4] Copyright 2008, Just Add Power Cardware Co., Inc. All Rights Reserved. Page 21 of 28...
-
Page 22: Total Control Console System Setup
IR IN Led will flash; to indicate the IR learning is finished. (Repeat steps 1~3 to setup the other IR functions you want to teach the system) Copyright 2008, Just Add Power Cardware Co., Inc. All Rights Reserved. Page 22 of 28... -
Page 23: Group Port Setting
1280*1024. For example, to set up the Video2 device output resolution to be 800*600: Press 1 time ◊ Press 1 time (will let you see the resolution setting changes on the projectors) ◊ Press 1 time Copyright 2008, Just Add Power Cardware Co., Inc. All Rights Reserved. Page 23 of 28... - Page 24 ◊ To quit the scaler resolution setup mode, press 1 time. Spare F keys: reserved for future application Copyright 2008, Just Add Power Cardware Co., Inc. All Rights Reserved. Page 24 of 28...
-
Page 25: Basic Trouble Shooting Techniques
Step 3: Split the row near the “middle” to see if the trouble goes away. If the problem is “fixed”, you now know that the trouble is with a device in the disconnected stations. Otherwise the problem is within the remaining connected stations. Genie Copyright 2008, Just Add Power Cardware Co., Inc. All Rights Reserved. Page 25 of 28... -
Page 26: Specific Problem Diagnosis
Make sure the Terminator is installed in the row and is pushed into the port completely. θ Try a different terminator θ Try different cables (CAT5e and VGA extension). θ Copyright 2008, Just Add Power Cardware Co., Inc. All Rights Reserved. Page 26 of 28... - Page 27 Copyright 2008, Just Add Power Cardware Co., Inc. All Rights Reserved. Page 27 of 28...
- Page 28 Copyright 2008, Just Add Power Cardware Co., Inc. All Rights Reserved. Page 28 of 28...
Need help?
Do you have a question about the VBS-PTP-308B and is the answer not in the manual?
Questions and answers