Download Print this page
Slant/Fin LX-90 User's Information Manual
Slant/Fin LX-90 User's Information Manual

Slant/Fin LX-90 User's Information Manual

Direct-vent sealed combustion condensing boiler

Advertisement

Quick Links

User's nformation Manual
Lynx Direct-Vent Sealed Combustion Condensing Boiler
• Before operating this boiler, READ this manual.
• DO NOT attempt to install, service or repair this boiler yourself. There are no user serviceable
parts. Contact a qualified service agency if your boiler needs repair or maintenance. Ask your gas supplier for a
list of qualified service agencies.
• A qualified service agency should inspect the venting system of this boiler on an annual basis.
Your gas boiler must be installed and serviced by a qualified service agency or
gas supplier. The lack of proper service can result in a dangerous condition.
This manual must be left with owner, hung on or
adjacent to the boiler. Owner should retain manual
for future reference.
Residential • Gas fired • Hot Water Boilers
Model LX-90, LX-120, LX-150
FOR YOUR S FETY:
Printed in U.S.A. 1111
WARNING: If the information in this manual is
not followed exactly, a fire or explosion may
result causing property damage, personal
injury or loss of life.
__
DO NOT store or use gasoline or other
flammable vapors and liquids in the
vicinity of this or any other appliance.
__
WHAT TO DO IF YOU SMELL GAS
• DO NOT try to light any appliance.
• DO NOT touch any electrical switch
• DO NOT use any phone in your building.
• Immediately call your gas supplier
from a neighbor's phone. Follow the
gas supplier's instructions.
• If you cannot reach your gas supplier,
call the fire department.
__
Installation and service must be performed by
a qualified installer, service agency or the gas
supplier.
Part No. 81-5002
Publication No. LX1-UIM Rev.A

Advertisement

loading
Need help?

Need help?

Do you have a question about the LX-90 and is the answer not in the manual?

Questions and answers

Summary of Contents for Slant/Fin LX-90

  • Page 1 Residential • Gas fired • Hot Water Boilers User’s nformation Manual Lynx Direct-Vent Sealed Combustion Condensing Boiler Model LX-90, LX-120, LX-150 FOR YOUR S FETY: • Before operating this boiler, READ this manual. • DO NOT attempt to install, service or repair this boiler yourself. There are no user serviceable parts.
  • Page 2 6 3/4 3 3/8 2 3/4 16 1/4 WELCOME TO OUR V LUED CUSTOMER 16 1/4 You are now the owner of a Slant/Fin Lynx gas-fired boiler, LX-120 6 5/8 3 3/8 16 1/4 another quality heating product designed and manufactured...
  • Page 3 Lynx INSPECTION 1. VENTING AND AIR INTAKE SYSTEM REGULAR INSPECTION Your boiler and heating system will last an indefinitely long time at full efficiency, if it is inspected regularly and is kept Inspect the system regularly for condensation, corrosion, in good repair and adjustment. You, the user, should make sagging and/or physical damage.
  • Page 4 Lynx Figure 4. Non-direct vent, sidewall venting.
  • Page 5 Lynx Figure 5. Non-direct vent, venting through the roof. Figure 6. Non-direct vent, utilizing an existing chimney as a chase.
  • Page 6 Lynx Figure 7. Condensate disposal system about 12 to 15 psi pressure when temperature is about 2. CONDENSATE REMOVAL SYSTEM 70 to 100F and from 15 psi to 25 psi when temperature Lynx boilers are equipped with a built-in condensation is up to 195˚F.
  • Page 7 Lynx The combustion air supply must not be susceptible to C. Use only your hand to turn the gas supply shut off contaminants, which may cause corrosion or other valve. Never use tools. If the supply shut off will not turn damage to the heat exchanger and components of the by hand, don’t try to repair it, call a qualified service boiler, causing failure of these parts or unsafe...
  • Page 8 Lynx 3. While “t” is blinking, DHW tank temperature may be Removing Jacket Front Panel set to desired temperature (if tank is equipped with 1. Turn black screws ⁄ turn to open position. sensor). The setting range is between 104˚ to 185˚F. 2.
  • Page 9 Lynx Lynx Boiler Display Board “Boiler Operation Status” Mode Description & Temperature Display Display Boiler is on stand-by mode. Temperature display shows supply water Temp. Space heating mode. Temperature display shows supply water Temp. Domestic hot water mode. Temperature display shows supply waterTemp. Frost protection mode.** Temperature display shows supply water Temp.
  • Page 10 Lynx Table 2: Viewing and Changing Temperatures Press “Select” button for viewing different modes on “Mode Display” Mode Description & Temperature Display Display Space heating supply water temperature could be changed by pressing “Up/Down” button. Settable from Blinking 90˚F to 185˚F (steps of 1 F). The default valve is 176˚ F Press “Enter”...
  • Page 11 Lynx DIAGNOSTIC ERROR CODES ERROR INDICATION CODE WARNING: If an operational problem has occurred, the boiler will Water Outlet Sensor Open shut off and show an “A”, “E” or “H” in the mode display, along with an error code in the temperature display. Water Inlet Sensor Open Do not attempt performing any service under these conditions, but do note the mode and temperature dis-...
  • Page 12 ©Slant/Fin Corp. 2011 SLANT/FIN CORPORATION, Greenvale, N.Y. 11548 • Phone: (516) 484-2600 FAX: (516) 484-5921 • Canada: Slant/Fin , Mississauga, Ontario LTD/LTEE www.slantfin.com...

This manual is also suitable for:

Lx-150Lx-120Lynx lx-120