Long 360 Series Service Manual page 145

DESCRIPTION
X. Front Drive Axle (Side Drum) (Cont'd.)
Thickness of rings (54, Fig. B.IX/11) of front drive axle swinging
axle
Wear limit
Thickness of shims 1., b, Fig. B.IX/11 of tapered roller bearing
for steering axle
Thickness of shims (b and 1,) of the drive pinion
Thickness of shims (h) for the bevel pinion bearings
Front Drive Axle Side Reduction Gear
Backlash between tooth flanks of the driving and driven gears
Backlash between driven gear grooves and splined shaft
Max. permissible backlash
Shaft (43, Fig. B.IX/22) dia. for driving gear
Oia. of bearing needles for the double-type driving gear
Bore of bearing needle location
Backlash between shaft, bearing needles and location of driving
gear
Max. permissible backlash
Dia. of control shaft (16) for engaging fork (Fig. B.IX/21)
Location boring of control shaft from the reduction gear casing
Backlash between control shaft and its location
Max. permissible backlash
Shims for cover (9a, 9b, 9c)
Shim thickness (29) for the driving gear
Specification of spring (23) for the lock ball (22) of control shaft:
-free length
-length under load
-check load
XI. Front Drive Axle (Center Driven)
Pinion bearing adjustment shims (SJ, Fig. B.X/6)
Pinion cone center distance adjustment shims (S•, Fig. B.X/6)
Rolling torque corresponding to assembly preload of bearings
Differential
Thickness of differential gear thrust washers
Diameter of pinion axles
Bore of differential pinion (fitted and reamed)
Assembly clearance between differential pinion bushings and axles
Interference fit of bushing on differential pinions
Backlash between differential gear and pinion teeth
Final Drive
Thickness of driven gear end washers (3, Fig. B.X/6)
Backlash of sun gear, planet gear and internal gear teeth
Power Traan · 141
FITS AND TOLERANCES
ln. (mm.)
0. 1146-0. 1217
0.1043
0.004-0.006·0.031
0.106-0.108-0.110
0.112·0.114·0.116
0.118-0.120-0.122
0.124·0.126·0.128
0.130
2.91·3.09
2.65
0.1-0.15-0.80
2. 7 ·2. 75-2.80
2.85-2.90-2.95
3.00-3.05·3.1 0
3.15-3.20·3.25
·3.30
0.004-0.005-0.006 0.100-0.125-0.150
0.004-0.008 0.100-0.200
0.0006·0.0054 0.14·0.137
0.014 0.35
0.9837-0.9843 24.987·25.000
0 .. 1177-0.1181 2.990·3.000
1.2217-1.2225
31.030·31.050
0.0012·0.0033
0.030-0.083
0.008
0.20
0.6292-06297 15.982·15.994
0.6306·0.6315
16.016-16.040
0.0009-0.0023
0.022·0.058
0.060
0.15
0.004-0.008·0.012 0.1·0.2·0.3
0.05 78·0.0603
1.470·1.530
0.9449 24
0.5512
14
26.5 lbs.
12 kg.
0.049·0.051·0.055 1.25·1.3·1.4·1.5
0.059-0.063·0.065 1.6·1.65·1. 7 ·1.8
0.067·0.071
0.004·0.008·0.019
0.1·0.2-0.5
1.08-2.02 ft. lbs. 1.46·2.74 N·m
0.0567 to 0.0614 1.47 to 1.53
0.9432 to 0.9440 23.959 to 23.980
0.9527 to 0.9477 24.020 to 24.072
0.0016 to 0.0044 0.040to0.113
0.0020 to 0.0098 0.050 to 0.250
0.0059 to 0.0078 0.15 to 0.20
0.0578 to 0.0602
1.47 to 1.53
0.004 to 0.008 0.10 to 0.20