To use the tether strap • To attach the One-Safe Infant Carrier to the stroller page 14 • To remove the One-Safe Infant Carrier from the stroller page 15 page 16 • Product care and maintenance Customer service #14275-Safety 1st-Shuttle Stroller Sky Black-05-13...
• Do not attempt to lift the stroller by the bumper bar or child tray, if it has one. • Remove the child from the stroller before going up or down stairs or escalators. • Regularly inspect the stroller for any parts that are loose, broken, torn or missing. Attend to the problem as soon as it is noticed. • Use only those accessories which are supplied by Dorel Australia, and approved for use with this stroller. • Do not run or jog with this stroller. • Do not use the stroller near an open fire, barbecue or exposed flame. • To avoid danger of suffocation, keep any plastic bags away from babies and children. • Use the tether strap to prevent the stroller rolling away. • Keep children away from the stroller when unfolding and do not let them play with the folded stroller. • Engage front wheel swivel lock (where applicable), to lock front wheel(s) when travelling on rough or uneven surfaces. • This product is not intended for commercial use. • Never put hot liquids in any cup holder (when fitted). • The weight of the child shall not exceed 20kg. Carry basket capacity 4kg. #14275-Safety 1st-Shuttle Stroller Sky Black-05-13...
Instruction Manual & User Guide Assembling: Shuttle Stroller Sky Black TO UNFOLD THE STROLLER • Remove the security tie, if the stroller has one. • Release the storage latch by pulling the latch away from the frame, as per Figure 1. Figure 1 Grasp the footrest and lift it as high as possible so that it ‘clicks’ into place, • as per Figure 2. Figure 3 Figure 2 Turn assembly upside down, press the white • release button (3A) and lift up the handlebar (3B) until both frame latches ‘click’ into the locked position (3C), as per Figure 3.
Instruction Manual & User Guide Assembling: Shuttle Stroller Sky Black (cont) TO ASSEMBLE THE FRONT WHEELS Align the pins on the tops of the front wheels with • the holes in the underside of the wheel housings, as per Figure 4 (A). • Firmly push the pins into the housing until they ‘click’ into place, as per Figure 4 (B). Check the wheels are attached by attempt- ing to pull them out again. Figure 4 TO USE THE FRONT WHEEL SWIVEL LOCKS Slide the slider in the middle of the unit up or •...
Instruction Manual & User Guide Assembling: Shuttle Stroller Sky Black (cont) TO REMOVE THE FRONT WHEELS Should only be performed by an adult. • Lay stroller on its side, as per Figure 6. • Align the swivel lock slider with the slot vertically and ensure the locking button is visible inside the hole located on the inside of the front swivel wheel vertical shaft housing. • Once visible, press on the tab with the screwdriver and pull on the wheel assembly to remove. Figure 6 Lay stroller on the other side and repeat the step above to remove the opposite wheel assembly.
Instruction Manual & User Guide Assembling: Shuttle Stroller Sky Black (cont) TO ASSEMBLE THE REAR WHEELS Push each wheel into position, as per Figure 7. • Check that both wheels are properly attached by attempting to pull them out. Figure 7 TO REMOVE THE REAR WHEELS • Press the metallic release button Figure 8 (A), located on the rear axle inwards and pull the wheel Figure 8 (B) outwards. Repeat same step for other wheel.
Instruction Manual & User Guide Using: Shuttle Stroller Sky Black (cont) TO FIT THE SEAT • The seat is suitable for newborn. If your child is not able to sit up unassisted, use the fully reclined position only. Placing the seat into position. • Lower the seat onto the frame until it ‘clicks’, as per Figure 10.
Instruction Manual & User Guide Using: Shuttle Stroller Sky Black (cont) TO FIT & REMOVE THE BUMPER BAR • To Fit. Align and insert the locator pins into the mounting holes on the armrests until they ‘click’ and lock in place at both ends, as per Figure 13 (1). • To Remove. Figure 13 Press button (A) located on each side of the bumper bar and pull it clear of the stroller, as per Figure 13 (2).
Instruction Manual & User Guide Using: Shuttle Stroller Sky Black (cont) TO FIT THE BOOTCOVER • The bootcover is attached to the frame by attaching the two velcro straps at the top of the bootcover on each side of the frame, as per Figure 16. • Hook the other end of the bootcover to the underside of the footrest. Figure 16 TO ADJUST HANDLE HEIGHT • Push adjustment button (1) located on the centre of the handlebar in (A) and slide the handle bar up or down to the desired height (B). • While sliding, release button to allow handle bar to lock into place with a ‘click’, as per Figure 17.
Instruction Manual & User Guide Using: Shuttle Stroller Sky Black (cont) TO FOLD THE STROLLER • Apply the brakes, remove the bootcover, raincover and any items in the basket, disengage the front wheel swivel locks. • Remove the seat prior to folding, as per page 6. • Lower the handle height, squeeze latch 1 top centre of the handle. • Simultaneously push down on the release latch 2 as per Figure 18 (A) on the right side of the handle with one hand and press release button 3 on the left of the handle to lower the handle bar, as per Figure 18 (B).
Instruction Manual & User Guide Using: Shuttle Stroller Sky Black (cont) TO SECURE YOUR CHILD A five-point harness is provided to secure your child. • The harness straps can be adjusted by moving each strap’s slider • The buckle is released by squeezing the buckle locks together. When not in use, disconnect shoulder strap/ waist straps from the buckle. TO USE THE TETHER STRAP Correct use of the tether strap will prevent a stroller runaway and possible injury to your child.
Instruction Manual & User Guide Using: Shuttle Stroller Sky Black with One-Safe Infant Carrier TO ATTACH THE ONE-SAFE INFANT CARRIER TO THE STROLLER • Remove the seat from the stroller, as per Figure 10 Page 9. To remove seat. • Lower the One-Safe Infant Carrier (facing the handle) into the seat mounting brackets of the Shuttle Stroller, as per Figure 21, until you hear them both ‘click’ into place, as per Figure 22. Figure 21 Figure 22 To ensure the One-Safe Infant Carrier is locked into place, lift up on the capsule handle.
Instruction Manual & User Guide Using: Shuttle Stroller Sky Black with One-Safe Infant Carrier TO REMOVE THE ONE-SAFE INFANT CARRIER FROM THE STROLLER • Extend the One-Safe Infant Carrier canopy/carry handle fully forward, press the red buttons (A) on each side of the Shuttle Stroller, as per Figure 23, • Lift the One-Safe Infant Carrier clear of the stroller, as per Figure 24. Figure 23 Figure 24 For operational features of the capsule, please refer to the instruction manual provided with your One-Safe Infant Carrier.
Need help?
Do you have a question about the Sky Black and is the answer not in the manual?
Questions and answers