Jonsered CS 2137 Instruction Manual
  1. Manuals
  2. Brands
  3. Jonsered Manuals
  4. Chainsaw
  5. CS 2137
  6. Instruction manual

Jonsered CS 2137 Instruction Manual

Jonsered gas chainsaw instruction manual
Hide thumbs Also See for CS 2137:
Table of Contents

Advertisement

Quick Links

Instruction Manual
Manuel d'instructions
Betriebsanweisung
Manual de instrucciones
English
Please read these instructions carefully and make sure you understand
them before using this unit.
Français
Avant d'utiliser cet appareil, veuillez lire attentivement les instructions et
assurez--vous de les avoir comprises.
Deutsch
Lesen Sie diese Hinweise zur Handhabung des Geräts aufmerksam durch.
Verwenden Sie es erst, wenn Sie sicher sind, daß Sie alle Anweisungen
verstanden haben.
Español
Lea atentamente las instrucciones y asegúrese de entenderlas antes de
utilizar esta unidad.
R
CS2137
530163281
12/11/02

Advertisement

Table of Contents
loading

Related Manuals for Jonsered CS 2137

Summary of Contents for Jonsered CS 2137

  • Page 1 Instruction Manual Manuel d’instructions Betriebsanweisung Manual de instrucciones English Please read these instructions carefully and make sure you understand them before using this unit. Français Avant d’utiliser cet appareil, veuillez lire attentivement les instructions et assurez--vous de les avoir comprises. Deutsch Lesen Sie diese Hinweise zur Handhabung des Geräts aufmerksam durch.

  • Page 2: Identification Of Symbols

    IDENTIFICATION (WHAT IS WHAT?) Chain Front Hand Guard Adjustment Tool (Bar Tool) Muffler Chain Bumper Bar Oil Fill Cap Spike Cylinder Cover Throttle Lockout Rear Handle Throttle Choke/ Chain Trigger Fast Idle Brake Lever IDENTIFICATION OF SYMBOLS WARNING! saw can be dangerous! Care- less or improper use can cause serious or even fatal injury.

  • Page 3: Safety Rules

    WARNING Always spark plug wire and place wire where it can- not contact spark plug to prevent accidental starting when setting up, transporting, ad- justing or making repairs except carburetor adjustments. Because a chain saw is a high-speed wood- cutting tool, special safety precautions must be observed to reduce the risk of accidents.
  • Page 4 S Mix and pour fuel in an outdoor area on bare ground; store fuel in a cool, dry, well venti- lated place; and use an approved, marked container for all fuel purposes. Wipe up all fuel spills before starting saw. S Move at least 10 feet (3 meters) from fuel- ing site before starting engine.

  • Page 5: Kickback Safety Features

    Elbow locked Thumb on underside of handlebar S Keep a good, firm grip on the saw with both hands when the engine is running and don’t let go. A firm grip will help you reduce kickback and maintain control of the saw. Keep the fingers of your left hand encir- cling and your left thumb under the front handlebar.

  • Page 6: Assembly

    SAFETY NOTICE: Exposure vibrations through prolonged use of gasoline powered hand tools could cause blood vessel or nerve damage in the fingers, hands, and joints of people prone to circulation disorders or abnormal swellings. Prolonged use in cold weather has been linked to blood vessel damage in otherwise healthy people.

  • Page 7: Operating Unit

    Place chain onto the sprocket 7. Place chain over and behind clutch, fitting the drive links in the clutch drum sprocket. 8. Fit bottom of drive links between the teeth in the sprocket in the nose of the guide bar. 9.

  • Page 8: Starting A Flooded Engine

    will cause engine damage. When mixing fuel follow the instructions printed on the container. Always read and follow the safety rules relating to fuel before fueling your unit. IMPORTANT Experience indicates that alcohol blended fuels (called gasohol or using ethanol or methanol) can attract moisture which leads to separation and formation of acids during storage.

  • Page 9: Cutting Methods

    S The inertia activated chain brake is acti- vated if the front hand guard is pushed for- ward, either manually or by centrifugal force. S If the brake is already activated, it is disen- gaged by pulling the front hand guard back toward the front handle as far as possible.
  • Page 10 NOTCH CUT AND FELLING THE TREE S Make notch cut by cutting the top of the notch first. Cut through of the tree. Next complete the notch by cut- ting the bottom of the notch. See illustra- tion. Once the notch is cut remove the notch of wood from the tree.

  • Page 11: Limbing And Pruning

    S Roll the log over and finish with a second overcut. S Give special attention to logs under strain to prevent the saw from pinching. Make the first cut on the pressure side to relieve the stress on the log. BUCKING USING A LOG OR SUP- PORT STAND S Remember your first cut is always on the...

  • Page 12: Service And Adjustments

    SERVICE AND ADJUSTMENTS WARNING : Disconnect the spark plug before performing maintenance, except for carburetor adjustments. We recommend all service and adjustments not listed in this manual be performed by an Authorized Service Dealer. MAINTENANCE SCHEDULE Check: Fuel mixture level .

  • Page 13: Chain Sharpening

    CHAIN SHARPENING Chain sharpening is a complicated task that requires special tools. We recommend that you refer chain sharpening to a professional chain sharpener. CARBURETOR ADJUSTMENTS WARNING : The chain will be moving during most of this procedure. Wear your pro- tective equipment and observe all safety pre- cautions.

  • Page 14: Declaration Of Conformity

    EU Declaration of Conformity relating to 2000/14/EC We, Poulan/Weed Eater Division, Electrolux Home Products, Inc., Texarkana, TX, 75501, USA, Tél. : +1 903 223 4100, declare under sole responsibility that the Jonsered model CS2137 chain saw was assessed in accordance with Annex V of the DIRECTIVE and from serial numbers 2002--249(N or D)00001 and onwards, conforms to the provisions of the DIRECTIVE.

  • Page 15: Technical Data Sheet

    1/3 idle, 1/3 full load, 1/3 full speed. 5/32 / 4,0 85" 30" 0" 2003 Jonsered SE--561 82 Huskvarna Huskvarna, Sweden CS2137 14/36 16/41 14/36 16/41 18,5 18,5...

Table of Contents