Summary of Contents for K-Star TAC-09CHSA
- Page 1 USER'S MANUAL Split Wall-Mounted Air Conditioner MODEL TAC-09CHSA TAC-12CHSA TAC-18CHSA TAC-24CHSA K-STAR INTERNATIONAL GROUP INC. TollFree:(800)893-2169 E-Mail:info@kstarus.com www.kstarus.com...
-
Page 2: Table Of Contents
CONTENTS Safety Precautions................1 Identification of Parts..............2 Remote Controller................4 Operation Instructions..............7 Maintenance................9 Protection...................10 Troubleshooting................11 Installation Instructions...............12 Preparation Before Use Before using the air conditioner, be sure to check and pre-set the following. Remote Controller Pre-setting The remote controller is NOT preset as Cooling Only Air Conditioner or Heat Pump by manufacturer. Each time after the remote Controller replaces of batteries or is energized, the symbol will flash from Cool... -
Page 3: Safety Precautions
Safety Precautions Symbols in this Use and Care Manual are interpreted as shown below. Be sure to follow this instruction. Be sure not to do. Pay attention to such a situation. Remove the power source plug from a socket. Warning: Incorrect handling could cause a serious Grounding is essential. -
Page 4: Identification Of Parts
Identification of Parts Indoor Unit Air Intake Front Panel Emergency Panel Display Panel Air Outlet Vertical Adjustment Louver Horizontal Adjustment Louver Charcoal Filter (optional) Electrostatic Filter (optional) Air Filter Remote Controller Air Intake Outdoor Unit Pipes and Power Connection Cord Drain Hose Note: Condensate water drains at COOLING or DRY operation. - Page 5 Identification of Parts Operating and Display Temperature display Switch display of environmental Run Indicator Timer Indicator temperature and It is on during It lights up during setting temperature operation. the set time. Power Indicator Sleep Indicator It lights up when It lights up during the power supply is on.
-
Page 6: Remote Controller
Remote Controller Remote Controller The remete controller transmits signals to the system. Setting Display ON/OFF button Signal Transmitting Window Transmitting display Used to start and stop operation . Transmits signals to the system. Time setting display Temperature setting display TIMER button setting temperature adjustment display Used to select TIMER operation. - Page 7 Remote Controller Remote Controller Some remote controller's display: Feel Cool Dry Fan Heat SLEEP TIMER ON TMIER OFF AUTO FEEL Timer HIGH COOL Timer HEAT SWING Auto Low Mid High Sleep Swing Note:The above remote controller is only for reference,please subject to the substantiality. When inserting the batteries for the first time or each time the batteries are replaced...
- Page 8 Remote Controller Remote Controller How to Insert the Batteries Please slide and remove the cover. Remove the battery cover according to the arrow direction. Insert new batteries making sure that the (+) and (-) of Slide the cover battery are matched correctly. upwardly in the direction of the Re-attach the cover by sliding it back into position.
-
Page 9: Operation Instructions
Operation Instructions FEEL mode operation procedure Operates by selecting automatically the operation mode(HEAT,DRY,FAN,COOL)depending on the room temperature during staring. With the remote controller pointing toward the air conditioner. Turning on Press button, when the appliance receives the ON/OFF signal, the RUN indicator of the indoor unit lights up. SLEEP TIMER ON TMIER OFF FEEL... - Page 10 Operation Instructions TIMER mode It is convenient to set the timer on with TIMER button when you go out in the morning to achieve a comfortable room temperature when you get home. You can also set timer off at night to enjoy a good sleep. When the Remote When the Remote Controller is ON,press...
-
Page 11: Maintenance
Maintenance Air filter maintenance Front panel maintenance It is necessary to clean the air filter after using it for about 100 hours. Turn off the appliance first before disconnecting Clean it as follows: Cut off the from power supply. power supply Stop the appliance Grasp position "a"... -
Page 12: Protection
Protection Operating condition Noise pollution The protective device maybe trip and stop the appliance in the cases listed below. Install the air conditioner at a place that can bear its weight in order to operate Outdoor air temperature is over 24c more quietly. -
Page 13: Troubleshooting
Troubleshooting The following cases may not always be a malfunction, please check it before asking for service. Analysis Trouble If the plug is not properly plugged. If batteries in the remote controller exhausted. Does not run If the protective device works to protect the appliance. If the protector trip or fuse is blown. -
Page 14: Installation Instructions
Installation Instructions Installation Diagram Distance from ceiling should be over 150 mm Distance from wall should be over 150mm Distance from the wall should be over 150mm Distance from floor should be over 2000mm over 500mm Air intake distance from the wall Air intake distance from should be over 300mm the wall should be... - Page 15 Installation Instructions Connecting of the Cabble Front panel Wiring between the indoor and outdoor units: Terminal (inside) 1) Remove the PCB cover from the indoor unit; 2) Refer to the wiring diagram attached to indoor unit COVER COVER when connecting cords to indoor unit terminals; 3) Reinstall the PCB cover.
- Page 16 Installation Instructions Indoor Unit Installation 1. Installing the Mounting Plate Decide an installing location for the mounting plate according to the indoor unit location and piping direction. Keep the mounting plate horizontally with a horizontal ruler or dropping line. Drill holes of 32mm in depth on the wall for fixing the plate. Insert the plastic plugs to the hole, fix the mounting plate with tapping screws.
- Page 17 Installation Instructions NOTE NOTE Piping Joints Thermal Insulation: Wrap the piping joints with thermal insulation materials and then wrap with a vinyl tape. wrapped with vinyl type The temperature of refrigerant circuit Thermal insulation will be high, please keep the interconnection able away from the copper tube.
- Page 18 Installation Instructions 4. Connecting of the Cable Front panel Terminal (inside) Indoor Unit Connect the power connecting cord to the indoor unit by connecting the wires to the terminals on the control board individually in accordance with the outdoor unit Cabinet connection.
-
Page 19: Vacuum Pump
Installation Instructions Outdoor Unit Installation 1.Install Drain Port and Drain Hose (for heat-pump model only) The condensate drains from the outdoor unit when the unit operates in heating mode. In order to protect the environment, install a drain port and a drain hose to direct the condensate water. Just install the drain port and rubber washer to the chassis of the outdoor unit, then Washer connect a drain hose to the port as the right figure shown. -
Page 20: Circuit Diagram
Installation Instructions Interconnection Cable Take off the cover for Interconnection cable of outdoor unit. Take off the block for Interconnection cable, then put the core of the power wire to the terminal and fix it according to the diagrams pasted to indoor and outdoor unit separately. Fix the accessory cable with the Interconnection cable block. - Page 21 Installation Instructions How to Purge Air Tubes (1). Unscrew and remove caps from 2 and 3-way valves. (2). Unscrew and remove cap from service valve. (3). Connect vacuum pump flexible hose to the service valve. (4). Start vacuum pump for 10-15 minutes until reaching a vacuum of 10 mm Hg absolutes. (5).