Operating Temperature : 50 °F to 104 °F (10 °C to 40 °C) Humidity : 10 % to 80 % Storage Temperature : -13 °F to 113 °F (-25 °C to 45 °C) Humidity : 5 % to 95 % ML17NS ML17AS TV System Tunning Frequency Synthesize...
2 Product Specifications 2-2 Pin Assignments Sync 15-Pin Signal Cable Connector Type Separate Composite Sync-on-green Pin No. Green Green Green + H/V Sync Blue Blue Blue GND (DDC Return) GND (DDC Return) GND (DDC Return) GND-Red GND-Red GND-Red GND-Green GND-Green GND-Green GND-Blue GND-Blue...
2 Product Specifications 2-3 Timing Chart This section of the service manual describes the timing that the computer industry recognizes as standard for computer-generated video signals. Table 2-1. Timing Chart Timing No. Originator VESA VESA VESA Mode Name VGA2 VGA3 640/75Hz 640/85Hz 800/75Hz...
Page 5
2 Product Specifications Table 2-1. Timing Chart (Continued) Timing No. VESA VESA VESA VESA VESA VESA Originator 800/85Hz 1024/60Hz 1024/75Hz 1024/85Hz 1280/75Hz 1280/60Hz Mode Name 800x600 1024x768 1024x768 1024x768 1280x1024 Resolution (HxV) 1280x1024 HORIZONTAL 63.981kHz 53.674kHz 48.363kHz 60.023kHz 68.677kHz 79.976kHz Frequency 18.631µs 20.677µs...
3 Disassembly and Reassembly This section of the service manual describes the disassembly and reassembly procedures for the SyncMaster 170MP monitor. WARNING: This monitor contains electrostatically sensitive devices. Use caution when handling these components. 3-1 Disassembly Cautions:1. Disconnect the monitor from the power source before disassembly. 2.
Page 7
3 Disassembly and Reassembly 4. Remove the Stand Rear from the Stand 3-1-6 Wire frame stand Disassembly (option) assembly. 1. Carefully pull the cover hinge. 5. Remove the Stand Front from the Stand 2. Remove the cover vesa from the Stand assembly.
Page 8
3 Disassembly and Reassembly 3. Please take out the lamp units from the LCD module. 4. Please fix the new lamp units on the LCD module : opposite process 2 and 3 Replacement of lamp unit should be done at the power off state and rcommended clean bench condition.
Page 9
3 Disassembly and Reassembly Memo SyncMaster 170MP...
4 Alignments and Adjustments 4-1.General Alignment Instuction 1. Usually, a color TV-VCR needs only slight touch-up adjustment upon installation. Check the basic characteristics such as height, horizontal and vertical sync. 2. Use the specified test equipment or its equivalent. 3. Correct impedance matching is essential. 4.
Page 11
4 Alignments and Adjustments Memo SyncMaster 170MP...
5 Troubleshooting 5-1 No Power Does proper DC 12 V appear at Check SMPS PCB and Adapter. DC jack connected to CN102? Does proper DC 5 V appear at Check IC103. Pin 1 of IC103? Does proper DC 2.5 V appear at Check FT115 and IC505.
Page 13
5 Troubleshooting 5-2 No Video (PC Signal) Power indicator is green Does the signal appear at Pin 7, Check R155 ~ R157, C151 ~ C153. 15, 22, of IC107? Does the clock pulse appear at Check IC107 and related circuit of IC107. Pin 115, 117 of IC107? Does the clock pulse appear at Check related circuit of IC301.
Page 14
5 Troubleshooting 5-3 No Picture (TV, Video 1, Video 2) Check Pin 16 (AGC), 12 (CVBS) of Check IC101 and replace the tuner. IC703 (TDA9810) Check Pin 15 (CVBS) of IC204 Replace IC204. (STV6400D) Check related circuit of IC504 and Check IC504 (VPC3230D) replace IC504.
5 Troubleshooting 5-4 No Sound Does the high signal at R822? Check R856 and replace Q801. Check Pin 12 of IC800 (TDA7268) Replace IC800. Check Pin 60, 67 of Replace IC801 (MSP3450). IC801 (MSP3450) Check IC703, tuner, related circuit of IC703 and tuner SyncMaster 170MP...
Page 16
6 Exploded View and Parts List SyncMaster 170MP...