Titan Tool ADVANTAGE 500 Owner's Manual

Electric piston pump

Advertisement

Quick Links

ADVANTAGE 500
Electric Piston Pump
Model Numbers:
Stand
Upright Cart
Lowboy Cart
0552055
0552073
0552074
© Titan Tool Inc. All Rights Reserved. Form No. 0552843C
0711
Owner's Manual
Do not use this equipment
before reading this manual!
NOTE: This manual contains important
warnings and instructions. Please
read and retain for reference.

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the ADVANTAGE 500 and is the answer not in the manual?

Questions and answers

Summary of Contents for Titan Tool ADVANTAGE 500

  • Page 1 ADVANTAGE 500 Electric Piston Pump Model Numbers: NOTE: This manual contains important Stand 0552055 warnings and instructions. Please Upright Cart 0552073 read and retain for reference. Lowboy Cart 0552074 © Titan Tool Inc. All Rights Reserved. Form No. 0552843C 0711 •...
  • Page 2: Safety Precautions

    • Use lowest possible pressure to flush equipment. reconstructive hand surgeon may be advisable. • Do not spray onto pump assembly. © Titan Tool Inc. All rights reserved.
  • Page 3: Specifications

    Maximum hose length ....300’ (91.4 m) • Do not use the hose as a strength member to pull or lift the equipment. • Do not lift by cart handle when loading or unloading. © Titan Tool Inc. All rights reserved.
  • Page 4: Table Of Contents

    Safety Precautions section at the front of this hose and into the waste container. manual before operating this equipment. 7. Turn off the unit by moving the ON/OFF switch to the OFF position. © Titan Tool Inc. All rights reserved.
  • Page 5: Preparing To Paint

    NOTE: Turning the pressure up higher then needed to atomize the paint will cause premature tip wear and additional overspray. © Titan Tool Inc. All rights reserved.
  • Page 6: Pressure Relief Procedure

    If the pressure is set too low, tailing will appear or the paint will spatter out in gobs rather than in a fine spray. Paint tailing pattern Do not flex wrist while spraying. © Titan Tool Inc. All rights reserved.
  • Page 7: Cleanup

    14. Follow the “Pressure Relief Procedure” found in the Operation section of this manual. 15. Unplug the unit and store in a clean, dry area. IMPORTaNT: Do not store the unit under pressure. © Titan Tool Inc. All rights reserved.
  • Page 8: Replacing The Prime/Spray Valve

    Disconnect the black and red wires from the Filter capacitors. Disconnect the black and red wires from the motor. 10. Loosen and remove the four motor mounting screws. Pump Manifold 11. Pull the motor out of the gear box housing. © Titan Tool Inc. All rights reserved.
  • Page 9: Replacing The Gears

    8. Position the fan shroud over the motor fan. Secure the fan shroud with the two fan shroud screws. 9. Slide the motor cover over the motor. Secure the motor cover with the four motor cover screws. © Titan Tool Inc. All rights reserved.
  • Page 10: Replacing The Transducer

    If the seat is Retainer damaged, reverse or replace the seat. 5. Remove, clean, and inspect the outlet valve cage, crush washer and outlet valve ball. Replace if they are worn or damaged. © Titan Tool Inc. All rights reserved.
  • Page 11: Siphon Tube (Upright Cart Only)

    NOTE: coat the piston guide tool and the piston rod with grease before inserting them into the pump manifold. © Titan Tool Inc. All rights reserved.
  • Page 12: Troubleshooting

    The unit lacks power. The pressure adjustment is too low. Rotate the pressure control knob clockwise to increase the pressure setting. Improper voltage supply. Reconnect the input voltage for 120V AC. © Titan Tool Inc. All rights reserved.
  • Page 13 Notes © Titan Tool Inc. All rights reserved.
  • Page 14 Se servir de la pression la plus basse possible pour vidanger s’avérer nécessaire de consulter un plasticien ou un spécialiste l’appareil. en chirurgie reconstructive de la main. • Ne pas pulvériser de produit sur la pompe. Français © Titan Tool Inc. Tous droits réservés.
  • Page 15 électrique de la prise avant de travailler sur l’équipement. • N’utilisez pas le tuyau pour tirer ou soulever l’équipement. • Ne pas soulever par la poignée de chariot en chargeant ou en déchargeant. © Titan Tool Inc. Tous droits réservés. Français...
  • Page 16 Use la presión más baja posible para enjuagar el equipo. consultar con un cirujano plástico o un cirujano especialista en • No rocíe el ensamblaje de la bomba. reconstrucción de las manos. Español © Titan Tool Inc. Todos los derechos reservados.
  • Page 17 • No utilice la manguera como elemento de fuerza para tirar del equipo o levantarlo. • No levantar por la manija del carro al cargar o descargando. © Titan Tool Inc. Todos los derechos reservados. Español...
  • Page 18: Parts List

    Siphon tube (upright cart only) ....1 (stand and low boy cart) ......1 710-046 Inlet screen (upright cart only) ....1 9885612 Return tube fitting ........1 ---------- Gear box assembly........1 0327226 Return hose clamp (not shown)....1 © Titan Tool Inc. All rights reserved.
  • Page 19: Motor Assembly

    Warning label, explosion/injection 0295805 Shock hazard label 0507856 PRIME/SPRAY label Item Part # Description quantity 805-258 Siphon tube assembly ......1 805-259 Return hose assembly ......1 0279459 Hose clip ...........1 9850638 Tie wrap ............2 © Titan Tool Inc. All rights reserved.
  • Page 20: Gear Box Assembly

    Gear Box assembly NOTE: all electrical work should be performed by a Titan authorized service center. © Titan Tool Inc. All rights reserved.
  • Page 21: Stand Assembly

    Spacer ............4 0294635 Plug ............2 9885571 Plug ............2 856-002 Washer .............6 856-921 Screw ............4 0507655 Cord wrap ..........2 0551555 Screw ............4 0551665 Cart weldment (includes items 8 and 9) ...1 0278373 Wheel ............2 © Titan Tool Inc. All rights reserved.
  • Page 22: Fluid Section Assembly

    Filter assembly (includes items 21–27) 0552951 Repacking kit (includes items 2–4, 8 10–12, 16, 18, and 20) Raised Lip 0551509 Lower seal insertion tool O-Ring Install lower packings with raised lip and O-ring facing up. © Titan Tool Inc. All rights reserved.
  • Page 23: Low Boy Cart Assembly

    NOTE: all electrical work should be performed by a Titan authorized service center. Black Power cord Blue White Black White Black Pressure switch Green / yellow Blue White Switch Circuit Motor Capacitors breaker Black Black © Titan Tool Inc. All rights reserved.
  • Page 24: Limited Warranty

    Warranty Titan Tool, Inc., (“Titan”) warrants that at the time of delivery to the original purchaser for use (“End User”), the equipment covered by this warranty is free from defects in material and workmanship. With the exception of any special, limited, or extended warranty published by Titan, Titan’s obligation under this warranty is limited to replacing or repairing without charge those parts which, to Titan’s...

Table of Contents