Advertisement
3.2.2 ASSEMBLY/DISASSEMBLY OF CABINET PARTS AND ELECTRICAL PARTS
Disassembly procedure
STEP
Fig.
PART NAME
No.
No.
FA1-1
[1]
UPPER ASSY
FA1-2
[2]
CASS.COVER
FA2
[3]
TOP COVER
FA3
[4]
VF ASSY
FA4
[5]
LOWER ASSY
FA5
[6]
POWER UNIT
FA6
[7]
FRONT ASSY
FA7
[8]
MIC
-
[9]
REAR COVER ASSY
/[10]
REAR BOARD ASSY
FA8
[10]
REAR BOARD ASSY
[11]
OP BLOCK ASSY
FA9
[12]
BKT TOP
[13]
MAIN BOARD ASSY
FA10
[14]
MECHANISSM ASSY
FA11
[15]
BUTTON UNIT
UA1
[16]
JUNCTION BOARD ASSY
[17]
COVER UPPER
UA2
[18]
MONITOR ASSY
[19]
SPEAKER
UA3
NOTE1a:
When removing the screw(No.6), open the MONITOR ASSY.
When removing the UPPER ASSY, close the MONITOR ASSY.
NOTE1b:
When attaching, be careful with the wiring.
• Place the FPC(BUTTON) in the FOOK properly.
• Place the WIRES(SPEAKER) properly between the GUIDE.
• Fold the FPC(JUNCTION) properly.
NOTE1c:
During the procedure, be careful not to damage the parts.
NOTE1d:
When attaching, fully pull up the KNOB(EJECT) to the OP
BLOCK as shown in the figure.
NOTE2:
When removing, remove the two screws (No.9, 10) with the
CASSETTE COVER open.
NOTE4a:
When removing, first pull out the FPC that connects the
CCD BOARD ASSY and the MAIN BOARD ASSY as the
FPC interferes with the procedure.
NOTE4b:
Refer to 3.2.3 DISASSEMBLY OF [4] VF ASSEMBLY for the
disassembly of VF ASSY.
NOTE5a:
When removing, be careful in handling the parts. Pay spe-
cial attention not to break fragile sections.
NOTE5b:
Screw No.15 is located under the COVER(JACK).
NOTE6a:
Be careful in handling the POWER UNIT as it consists of
three parts, and the parts are connected by the FPC.
NOTE6b:
When attaching, be sure to attach firmly.
POINT
NOTE
2(S1a),2(S1b),3(S1a),(S1d),
NOTE1a,b,c,d
L1a,b,c,d,e,f,g,3(L1h),L1j,CN1
2(L2a),4(S2),3(L2b)
NOTE2
2(S3),2(L3)
-
CN4a,b,S4a,S4b
NOTE4a,b
COVER(JACK),CN5,2(S5a),
NOTE5a,b
S5b,S5c,2(S5b),2(L5)
2(S6),2(L6a),2(L6b),L6c
NOTE6a,b
S7,L7a,b,CN7
-
S8,PLATE(MIC)
NOTE8
2(S9),L9a,b,CN9
NOTE9
S10
-
CN11,2(L11)
NOTE11a,b
4(S12),2(L12a),L12b
CN13a,b,c,d,e,S13,L13
-
L14,4(S14)
NOTE14
CN15,L15a,S15,L15,b,c,d,e,
NOTE15
CN16a,b
NOTE16a,b,c
2(S17)
NOTE17
2(S18),2(L18)
NOTE18
5(S19),L19a,b,c,d,BKT(HINGE),
KNOB(SILDE),KNOB(EJIECT),
NOTE19a,b
BKT(GROUND)
NOTE8:
When attaching, be careful in wiring.
NOET9:
During the procedure, be careful not to damage the EJECT
SWITCH.
During the procedure, leave the CASSETTE COVER closed.
NOTE11a:
When attaching, do not connect the CCD MAIN BOARD
FPC to the MAIN BOARD first, connect the FPC after attach-
ing the VF ASSY.
NOTE11b:
Refer to 3.2.5 ASSEMBLY/DISASSEMBLY OF [11] OP
BLOCK ASSMBLY/CCD BOARD ASSEMBLY of OP BLOCK
ASSY.
NOTE14:
When removing, be careful not to damage the parts or cut the wires.
NOTE15:
During the procedure, be careful not to damage the parts.
When attaching, be careful with the wiring.
NOTE16a:
When attaching, be careful with the locations of the SWITCH
and the KNOB(VID/MEM SW). (DSC MODEL ONLY)
NOTE16b:
During the procedure, be careful not to damage the SWITCH.
When attaching, leave the MONITOR ASSY open.
NOTE16c:
When attaching, be careful with the wiring of the WIRE
(SPEAKER).
NOTE17:
When removing, push the COVER from the backside, and
be careful in handling the parts.
NOTE18:
Refer to 3.2.4 DISASSEMBLY OF [18] MONITOR ASSEM-
BLY for the disassembly of the MONITOR ASSY.
NOTE19a:
During the procedure, be careful in handling the parts.
NOTE19b:
When attaching, be careful with the wiring and the attach-
ment locations of the parts.
Destination of connectors
CN.
CONNECTOR
No.
CN1
MAIN
CN103
CN4a MAIN
CN4201
CN4b MAIN
CN7801
CN5
MAIN
CN105
CN7
MAIN
CN2601
CN9
MAIN
CN101/CN106
CN11 MAIN
CN4901
CN13a MAIN
CN1604
CN13b MAIN
CN1603
CN13c MAIN
CN1602
CN13d MAIN
CN3501
CN13e MAIN
CN1601
CN15 JUNCTION
CN403
CN16a JUNCTION
CN404
CN16b JUNCTION
CN402
PIN
No.
JUNCTION
CN401
26
CCD
CN5001
20
VF
CN7001
18
POWER UNIT
-
12
MIC
-
4
REAR
CN501/CN504 40/34
OP BLOCK ASSY
-
26
SENSOR
-
16
CAPSTAN MOTOR
-
18
DRUM MOTOR
-
11
HEAD
-
8
LOADING MOTOR
-
8
/ROTARY ENCODER
BUTTON UNIT
-
6
SPEAKER
-
2
MONITOR
CN7601
22
(No.YF173)1-7
Hide quick links:
Advertisement
