Download Print this page

Pottery Barn Teen EMERSON BUNK BED FULL OVER FULL User Manual

Emerson bunk bed full over full

Advertisement

Quick Links

WARNING:
could result in serious injury or death. To help prevent serious or fatal injuries from
entrapment or falls:
Read all instructions before assembling bunk bed.
Before each usage or assembly, inspect bunk bed for damaged hardware, loose joints,
missing parts or sharp edges. DO NOT use bunk bed if any parts are missing or broken.
DO NOT use substitute parts. Contact Pottery Barn Kids for replacement parts and
instructional literature if needed.
Follow the information on the warnings appearing on the upper bunk end structure and
on the carton. DO NOT REMOVE WARNING LABEL FROM BED.
Always use the recommended size mattress or mattress support, or both, to help prevent
the likelihood of entrapment or falls.
Ensure thickness of mattress does not exceed 9 inches and the surface of mattress must
be at least 5 inches (127 mm) below the upper edge of guardrails.
Use only mattress which is 74"-75" long and
Do not allow children under 6 years of age to use the upper bunk.
Periodically check and ensure that the guardrail, ladder, and other components are in their
proper position, free from damage, and that all connectors are tight.
Do not allow horseplay on or under the bed and prohibit jumping on the bed.
Prohibit more than one person on the upper bunk.
Always use the ladder for entering and leaving the upper bunk.
Use of a night light may provide added safety precaution for a child using the upper bunk.
Always use guardrails on both long sides of the upper bunk. If the bunk bed will be placed
next to the wall, the guardrail that runs the full length of the bed should be placed against
the wall to prevent entrapment between the bed and wall.
The use of water or sleep flotation mattresses is prohibited.
If refinishing, use a non-toxic finish specified for children's products.
STRANGULATION HAZARD - Never attach or hang items to any part of the bunk bed
that are not designed for use with the bed; for example, but not limited to, hooks, belts
and jump ropes.
KEEP THESE INSTRUCTIONS FOR FUTURE REFERENCE.
PRE-ASSEMBLY:
Please read all instructions before beginning assembly.
For your safety and ease, assembly by two adults is recommended.
Remove all parts and hardware from box and lay out on a carpeted or scratch-free work surface, as this
will avoid damaging any parts during assembly. The shipping box provides an ideal work surface.
Do not dispose of any contents until assembly is completed to avoid accidentally discarding small parts or
hardware.
Use the parts and hardware lists to identify and separate each of the pieces included.
Note: Do not fully tighten all bolts until all parts are in place. Failure to follow these instructions may cause
the bolts to misalign during assembly.
The use of power tools for assembly is not recommended. Power tools can damage hardware or split
wood.
Date: 21-October-2011
Rev:
pottery barn teen
EMERSON BUNK BED FULL OVER FULL
Failure to follow these warnings and assembly instructions
52.5"-53.5"
wide on upper bunk.
04-000066-3
Page 1/7

Advertisement

loading

Summary of Contents for Pottery Barn Teen EMERSON BUNK BED FULL OVER FULL

  • Page 1 EMERSON BUNK BED FULL OVER FULL WARNING: Failure to follow these warnings and assembly instructions could result in serious injury or death. To help prevent serious or fatal injuries from entrapment or falls:  Read all instructions before assembling bunk bed.
  • Page 2: Parts Included

    PARTS INCLUDED Part Included Box 4: Part Included Box 2: Part Included Box 3: Part Included Box 1: 6. Ladder (1x) 2. Lower End Panel (2x) 3. Side Rails (4x) 1. Upper End Panel (2x) 8. Roll Slats (2x) 7. Wood Block Without Holes (4x) 4.
  • Page 3 ASSEMBLY INSTRUCTIONS Insert the barrel nut (A) and wooden dowel (J) into pre-drilled holes at two ends of side rails (3). Ensure the thread on barrel nut facing out and align with pre- drilled hole on the edge of side rail 2.
  • Page 4 3. Roll out the slat roll (8) onto the support rail on the inner side of side rail (3). Secure each slat by long screw (G) at two ends using a Phillips head screwdriver (Not Included). Repeat step 2 to attach the side rail (3) to the upper end panel (2). (32x) (8x) 4.
  • Page 5 5. Roll out the slat roll (8) onto the support rail on the inner side of side rail (3) of upper bed. Secure each slat by long screw (G) at two ends using a Phillips head screwdriver (Not Included). (32x) 6.
  • Page 6 7. Place the upper bed onto the lower bed by aligning the pre-drilled holes on the bottom post of upper end panels (1) with metal dowels (H) that has just been installed on the lower bed end panel (2). 8. Slot the pre-fixed metal bracket on the ladder (6) onto the side rail (3) of upper bed. Secure the ladder (6) to the side rail (3) by short screw (I) at the center hole of metal brackets.
  • Page 7: Care Instructions

    9. Turn the pre-installed mending plate under the horizontal rail of long and short guard rail (4&5) over the side rail (3). Secure the mending plate with side rail (3) by medium screws (F). (5x) Optional the assembly for single bed Full – Full size used: 10.