Sanyo VPC-MZ3EX Service Manual page 3

1-2. CA2 CIRCUIT DESCRIPTION
1. Circuit Description
1-1. Scannning converter (Interlace converter)
This circuit uses the function of a 128-Mbit SDRAMs to con-
vert the non-interlaced signal which is output from the CCD
into an interlaced signal for the video monitor.
1-2. Camera signal processor
This comprises circuits such as the digial clamp circuit, white
balance circuit, γ circuit, color signal generation circuit, ma-
trix circuit and horizontal aperture circuit.
1. Digital clamp circuit
The optical black section of the CCD extracts 16-pixel aver-
aged values from the subsequent data to make the black level
of the CCD output data uniform for each line. The 16-pixel
averaged value for each line is taken as the sum of the value
for the previous line multiplied by the coefficient k and the
value for the current line multiplied by the coefficient 1-k.
2. White balance circuit
This circuit controls the white balance by using the AWB judge-
ment value computed by the CPU to control the gain for each
R, G and B pixel based on the CCD data which has been
read.
3. γ circuit
This circuit performs (gamma) correction in order to maintain
a linear relationship between the light input to the camera
and the light output from the picture screen.
4. Color generation circuit
This circuit converts the CCD data into RGB signals.
5. Matrix circuit
This circuit generates the Y signals, R-Y signals and B-Y sig-
nals from the RGB signals.
6. Horizontal aperture circuit
This circuit is used generate the aperture signal.
1-3. SDRAM controller
This circuit outputs address, RAS, CAS and AS data for con-
trolling the SDRAM. It also refreshes the SDRAM.
1-4. PIO
The expansion parallel port can be used for functions such
as stroboscope control and LCD driver control.
1-5. SIO (Serial control)
This is the interface for the 4-bit microprocessor.
1-6. USB control
This is comunicated PC with 12 Mbps.
1-7. TG, SG block
This is the timing generation circuit which generates the clocks
(vertical transfer clock and electronic shutter clock) which drive
the CCD.
1-8. Sound buffer
Audio memory
1-9. LCD driver
The 8-bit digital YUV signals which are input to the LCD driver
are converted to RGB signals, and the timing signal which is
necessary for LCD monitor display and the RGB signals are
then supplied to the LCD monitor.
1-10. LCD monitor
This is the image display device which displays the image
signals supplied from the LCD driver.
1-11. Memory card control
This reads data from the memory card and stores it in SDRAM,
and writes out the image data stored in SDRAM. In addition,
error correction is carried out when the data is read.
1-12. MJPEG compression
Still and continuous frame data is converted to JPEG format,
and movie images are compressed and expanded in MJPEG
format.
2. Outline of Operation
When the shutter opens, the reset signals, ZTEST0, ZTEST1,
ZTEST2 signals and the serial signals ("take a picture" com-
mands) from the 8-bit microprocessor are input and record
operation starts. When the TG drives the CCD, picture data
passes through the A/D and is then input to the ASIC as 10-
bit data. This data then passes through the DCLP, AWB, shutter
and γ circuit, after which it is input to the SDRAM. The AWB,
shutter, γ, and AGC value are computed from this data, and
two exposures are made to obtain the optimum picture. The
data which has already been stored in the SDRAM is read by
the CPU and color generation is carried out. Each pixel is
interpolated from the surrounding data as being either R, G
or B primary color data to produce R, G and B data. At this
time, correction of the lens distortion which is a characteristic
of wide-angle lenses is carried out. Aperture correction is car-
ried out, and in case of still picture the data is then compressed
by the JPEG method and in case of picture it is compressed
by MJPEG method and is written to compact flash card. When
the data is to be output to an external device, it is read JPEG
picture data from the compact flash card and output to PC via
the USB.
– 3 –