Wire Sizes; Unpacking And Checking Contents; List Of Loose Parts; Loose Parts - RIDGID EB4424 Owner's Manual

Wire Sizes

NOTE: Make sure the proper extension cord is used and
is in good condition.
The use of any extension cord will cause loss of power. To
keep this to a minimum and to prevent overheating and
motor burn-out, use the table shown to determine the min-
imum wire size (A.W.G.) extension cord.

Unpacking and Checking Contents

1. Remove tool from carton by lifting unit.
2. Place the tool on a secure, stationary work surface and
look the tool over carefully.
WARNING: For your own safety, never connect
plug to power source outlet, or insert switch key
until all assembly steps are complete and until you
have read and understood the entire owners man-
ual.
WARNING: To reduce the risk of injury, if any parts
are missing, do not attempt to assemble the
sander, plug in the power cord, or turn the switch
on until the missing parts are obtained and
installed correctly.

List of Loose Parts

NOTE: Before beginning assembly, check that all parts
are included. If you are missing any part, do not assem-
ble the sander. Call 1-800-4-RIDGID or E-mail us at
info@ridgidwoodworking.com if any parts are damaged
or missing. Sometimes small parts can get lost in pack-
aging material. Do not throw away any packaging until
sander is put together. Check packaging for missing
parts before contacting RIDGID.
Item Description
A Oscillating Edge Belt/Spindle Sander ..................... 1
B Spacer Ring Inserts

Loose Parts

A
F
G
NOTE: The sander is shipped with the 4" x 24" sanding
belt attached.
Use only 3-wire extension cords with 3-prong grounding
type plugs and 3-pole receptacles.
Item
Qty.
E
B
1/2" (1)
C
H
1/2"
NOTE: Parts shown are not actual size.
7
Extension
Cord Length
0-25 Ft.
26-50 Ft.
Description
1/2" I.D.................................................................... 1
1" I.D....................................................................... 1
1-1/2" I.D. ............................................................... 1
2" I.D....................................................................... 1
C Drums
3/4" x 4-1/2" ............................................................ 1
1" x 4-1/2" ............................................................... 1
1-1/2" x 4-1/2"......................................................... 1
2" x 4-1/2" ............................................................... 1
D Sandpaper Sleeves
1/2" x 4-1/2" ............................................................ 1
3/4" x 4-1/2" ............................................................ 1
1" x 4-1/2" ............................................................... 1
1-1/2" x 4-1/2"......................................................... 1
2" x 4-1/2" ............................................................... 1
E Sanding Belt (Installed)
4" x 24" ................................................................... 1
F Insert....................................................................... 1
G Owners Manual ...................................................... 1
H Bag of Loose Parts
Containing the following parts:
Rubber feet .................................................................4
Washer, Flat 21/64 x 1-3/4 x 1/8 .................................1
Washer, Flat 21/64 x 7/8 x 3/64 ..................................1
Washer, Flat 21/64 x 5/8 x 1/32 ..................................1
Switch Key ..................................................................1
Hex "L" Wrench 3/32 ...................................................1
Hex "L" Wrench 5/32 ...................................................1
Spacer Ring Inserts
1" (1) 1-1/2" (1)
Drums and Sandpaper Sleeves
D
3/4" 1"
Gauge
(A.W.G.)
16
14
Qty.
2" (1)
1-1/2" 2"