RIDGID EB4424 Owner's Manual page 25

Repair Parts
Parts List For RIDGID Oscillating Edge Belt/Spindle Sander
RIDGID parts are available on-line at www.ridgidparts.com
Key Part No.
No.
1
826358 Knob Spindle
2 805553-2 Washer 21/64 x 5/8 x 1/32
3 822304 Drum Sanding 3/4"
4 † Drum Sandpaper
5 825808 Plate Throat 2"
6 † Belt Sanding 4" x 24"
7 810993-2 Screw Set Half Dog 10/32 x 1/2
8 825841 Adapter Throat Plate
9 825544 Fan
10 805297-9 Screw Flat Hd 1/4-20 x 5/8
11 825523 Table Rear
12 825548 Plate Wear
13 825844 Nut Special Twin 1/4-20
14 825842 Screw Shoulder 1/4-20
15
16 825537 Bracket Table Lock
17 825852 Knob 1/4-20 x 3/4
18 159572-138 Screw Wash/Hd
19 808380-7 Screw Pan Hd 10-14 x 1/2
20 825840 Spring Detent
21 826803 Base
22 159572-186 Screw Hex Hd
23 824604 Screw Hex Wash/Hd
24 826783 • Motor Asm
25 826469 Follower Cam
26 805641-1 Ring Retaining 5133-31
27 826470 Housing
* Standard Hardware Item - May be purchased locally
† These parts are available where you purchased your sander.
• Any attempt to repair this motor may create a hazard unless repair is done by a qualified service technician. Repair
service is available at your nearest Authorized Service Center.
Model EB44240
Always order by Part Number—Not by Key Number
Description
Ty "T" 10-32 x 3/8
Ty "T" 1/4-20 x 1
Ty "T" 8-32 x 3/8
Figure 1
Key
Part No.
No.
28
822356
29 826801
30 825854
31 819012
32 9416630
33 826347
34 AC1000
35 817399-11
36 37837
37 825549
38 825537-1
39 825543
40 825524
41 803309-2
42 825525
43 825539-1
44 SP6001
45 37836
46 —
47 60358
48 805553-24
49 822304-1
50 822304-2
51 822304-3
52 825808-1
53 825808-2
54 825808-3
55 805642
25
Description
Nut Hex Flange Lock 8-32
Enclosure
Cord w/Plug
Foot
Screw Hex Hd Ty "T" 5/16-18 x 1
Switch Locking
† Key Switch
Relay
Wrench Hex "L" 5/32
Spacer Table Lock
Bracket Table Lock Left
Bolt Table Lock
Table Front
Screw Soc Set Lock 10-32 x 3/8
Plate Stop
Knob 1/4-20
Owners Manual
Wrench Hex "L" 3/32
Belt Sanding Assembly
(See Fig. 2)
* Washer 5/8 x 1-3/4 x 1/8
Washer 21/64 x 7/8 x 3/64
Drum Sanding 1"
Drum Sanding 1-1/2"
Drum Sanding 2"
Plate Throat 1-1/2"
Plate Throat 1"
Plate Throat 1/2"
Ring, Retaining 5160-50