LCD-Monitor Chassis : LTD22NS Model : T220HD SERVICE Manual TFT-LCD Monitor Contens 1. Precautions 2. Product specifications 3. Disassembly and Reassemble 4. Troubleshooting 5. Exploded View & Part List 6. Wiring Diagram 7. Schematic Diagram T220HD Refer to the service manual in the GSPN (see the rear cover) for the more information.
1. Precautions 1. Precautions 1-1. Safety Precautions Follow these safety, servicing and ESD precautions to prevent damage and to protect against potential hazards such as electrical shock. 1-1-1. Warnings For continued safety, do not attempt to modify the circuit board. Disconnect the AC power and DC power jack before servicing.
1. Precautions 1-2. Servicing Precautions WARNING: An electrolytic capacitor installed with the wrong polarity might explode. Caution: Before servicing units covered by this service manual, read and follow the Safety Precautions section of this manual. Note: If unforeseen circumstances create conflict between the following servicing precautions and any of the safety precautions, always follow the safety precautions.
1. Precautions 1-4. Installation Precautions For safety reasons, more than two people are required for carrying the product. Keep the power cord away from any heat emitting devices, as a melted covering may cause fire or electric shock. Do not place the product in areas with poor ventilation such as a bookshelf or closet. The increased internal temperature may cause fire.
3. Disassembly and Assembly 3. Disassembly and Assembly This section describes the disassembly and reassembly sequences for this monitor. Warning: As this monitor has parts that are sensitive to static electricity, be careful when handling them. 3-1. Disassembly Caution: 1. Turn the monitor off before beginning the disassembly process. 2.
Page 9
3. Disassembly and Assembly Description Photo Screws 3. Insert a flat screwdriver into the groove and then lift up and remove the cover. 4. After remove COVER-REAR, then disconnect SPEAKER , FUNCTION wire. 5. Disconnect LVDS cable from panel.
Page 10
3. Disassembly and Assembly Description Photo Screws 6. After disconnecting SHIELD-LAMP of left side, disassemble lamp wire between panel and IP Board. 7. Remove 8 marked SCREW of left picture. Disconnect IP board. ※ Reassembly procedures are in the reverse order of disassembly procedures.
Page 11
3. Disassembly and Assembly Description Photo Screws 9. Remove the IR module by tilting the left snap to the right. 10. Remove the LED module by sliding the snap designated in the right figure backwards. 11. Remove the two (2) screws and then remove the holders from the four (4) snaps designated in the right figure using the provided jig.
Page 12
3. Disassembly and Assembly Description Photo Screws 12. Remove the two (2) connectors. Caution : Servicing is not supported for the PCB. ▶Assembly 13. The assembly is in the reverse order of the disassembly. 14. Connect the disassembled snap and the LED module again.
2. Product specifications 2. Product specifications 2-1. Feature & Specifications Model T220HD Feature Supreme Digital Interface & Networking � - With a built-in HD digital tuner, it supports HD broadcasting with no particular set-top box and provides simple access with a single remote control.
Page 15
2. Product specifications Specifications Item Description Environmental Considerations Operating Temperature: 50˚C ~ 104˚F(10˚C ~ 40˚C) Operating Humidity : 10% ~ 80% Storage Temperature: -4˚C ~ 113˚C(-20˚C ~ 45˚C) Storage Humidity: 5% ~ 95% Antenna Input 75Ω Sound Characteristic -MAX Internal speaker Out : Right : 3W / Left : 3W -BASS Control Range : -8 dB ~ + 8dB -TREBLE Control Range : -8 dB ~ +8 dB -Headphone Out : 10 mW MAX...
Remark Remote Control & BN59-00678A Batteries (AAA x 2) Power Cord 3903-000085 Stand Body BN96-07347B Stand Base BN96-07345A Samsung Electronics Service center D-Sub Cable BN39-00244G CBF SIGNAL-DVI(D) BN39-00246K User’s Guide, Monitor Driver, BN96-07540A Natural Color Pro Software Cleaning Cloth BN63-01798A...
4. Troubleshooting 4. Troubleshooting 4-1. First Checklist for Troubleshooting Self-Test Feature Check Your monitor provides a self test feature that allows you to check whether your monitor is functioning properly. Turn off both your computer and the monitor. Unplug the video cable from the back of the computer Turn on the monitor.
4. Troubleshooting 4-2. No Power CN100 C129 C108 IC110 Q100 IC203 IC103 C135 Main Board Front Does proper 13V appear at pin No. 2 of CN100? ① Check IP Board Does proper 5V appear at pin No. Diagnostics 6 and 7 of CN100? ② Does proper 13V appear at C129? ①...
Page 20
4. Troubleshooting 4-2-1. Circuit diagrams when the power does not turn on...
4. Troubleshooting 4-3. PC (ANALOG) No Screen CN300 C509, C510 CN500 Main Board Front Does led persists green light after Diagnostics Check IP board power on? Does proper 5V appear at pin No. Check D-sub cable connection 9 of CN500? Does proper V and H-sync appear Check PC state at C510 and C509? ④, ⑤...
Page 23
4. Troubleshooting 4-3-1. Circuit diagrams and waveforms (Analog) when no screen is displayed on the monitor...
Page 24
4. Troubleshooting Analog PC 4-3-2. Waveforms when no screen is displayed ( ④ ⑤...
4. Troubleshooting 4-4. DVI No Screen CN300 IC600 CN500 CN501 Main Board Front Does led persists green light after Check IP board power on? Diagnostics Dose proper 5V appear at pin No. Check DVI cable connection 14 of CN501? Does proper signals appear at Check PC state pin No.6(SCL) ⑥...
Page 26
4. Troubleshooting (DVI No Screen) 4-4-1. Circuit diagrams and waveforms when no screen is displayed on the monitor...
Page 27
4. Troubleshooting DVI No Screen 4-4-2. Waveforms when a blank screen is displayed ( ⑥ ⑦ 4-10...
4. Troubleshooting 4-5. HDMI1 No Screen IC302 CN300 IC204 IC600 CN508 Main Board Front Does led persists green light after Check IP board power on? Diagnostics Dose proper 5V appear at pin No. Check HDMI cable connection 18 of CN508? Does proper signals appear at Change IC204 pin No.15(SCL) ⑧...
Page 29
4. Troubleshooting (HDMI1 No Screen) 4-5-1. Waveforms when a blank screen is displayed ⑧ ⑨ 4-12...
4. Troubleshooting 4-6. HDMI2 No Screen IC302 CN300 IC204 CN504 IC600 Main Board Front Does led persists green light after Check IP board power on? Diagnostics Dose proper 5V appear at pin No. Check HDMI cable connection 18 of CN504? Does proper signals appear at Change IC204 pin No.15(SCL) ⑧...
4. Troubleshooting 4-7. Faults and Corrective Actions Fault Photo Symptoms and Corrective Actions Remarks Symptoms: DVI signals are not recognized. * Refer to the Training Manual for information on inputting the DVI DDC. Causes: This fault occurs when the PC does not recognize the mode information because the DVI DDC has not been input to the monitor.
4. Troubleshooting 4-8. Adjustment 4-8-1. Service Instruction 1. Usually, a color TV-VCR needs only slight touch-up adjustment upon installation. Check the basic characteristics such as height, horizontal and vertical sync. 2. Use the specified test equipment or its equivalent. 3. Correct impedance matching is essential. 4.
4. Troubleshooting 4-10. Service Adjustment 4-10-1. White Balance - Calibration If picture color is wrong, do calibration first. Equipment : MSPG, Patten : 16 gray Execute calibration in Factory Mode Source(PC): 1024*768/60Hz ( Gray patten ) 4-10-2. White Balance - Adjustment If picture color is wrong, check White Balance condition.
Page 34
4. Troubleshooting 4-10-4. Method of Adjustment 1. Adjust the white balance of, Component and DVI Modes. (AV→Component) a) Set the input to the mode in which the adjustment will be made. (RF→DTV→PC→DVI). * Input signal - VIDEO Mode : Model #2 (744*484 Mode), Pattern #16 - DTV,DVI Mode : Model #6 (1280*720 Mode), Pattern #16 - HDMI Mode: Model #6(1280*720 Mode), Pattern #16 b) Enter factory color control, confirm the data.
4. Troubleshooting 4-11. Software Upgrade 4-11-1. Program Upgrading - MAIN 1. If you press MENU → SETUP → SW Upgrade, you’ll see below picture 2. Press ENTER, then you’ll see below picture. 3. Press ENTER 4. Micom program is now upgrading as below picture. 5.
Page 60
6. Wiring Diagram 6-2. Wiring Diagram - Main Board PC Stereo Digital Audio Output (Optical Output) USB (For updating code) Power Connector Connect with IP board HDMI Headphone RF ANT. PC Analog HDMI Audio R/ L, Component Function Connector 8P Speaker Connector 4P (Connect with function Assy) (Connect with Speaker Assy)
6. Wiring Diagram 6-3. Wiring Diagram - IP Board Power Connector 9P (Connect with MAIN Lamp Connector board) (Connect with panel inverter – left top of panel rear) Lamp Connector (Connect with panel inverter – left bottom of panel rear) AC Power socket...