Wesco T504 Manual Spare Parts List

Hide thumbs

Table Of Contents

Table of Contents

Quick Links

Download this manual

Manual / Handbuch

Spare parts list / Ersatzteilliste

Equipment Imp.-Exp. GmbH

•

D - 22391 Hamburg

Tel.: + 49 40 60009468-0

•

E - M a i l : i n f o @ w e s c o - n a v y. c o m

Zitterpappelweg 9

•

Fax: + 49 40 536 75 01

•

w w w . w e s c o - n a v y. c o m

•

Table of Contents

Summary of Contents for Wesco T504

Page 1 Manual / Handbuch Spare parts list / Ersatzteilliste Equipment Imp.-Exp. GmbH Zitterpappelweg 9 • • D - 22391 Hamburg Tel.: + 49 40 60009468-0 Fax: + 49 40 536 75 01 • • E - M a i l : i n f o @ w e s c o - n a v y. c o m w w w .
Page 2: Table Of Contents
Contents Before using your machine for Troubleshooting the first time The machine will not start Do not tumble dry Overheating cut-off Important safety instructions Drying takes too long Installation The laundry does not dry, or is too Grounding instructions Interrupting a program Technical information Packing material Technical data...
Page 3: Before Using Your Machine For The First Time
Before using your machine for the first time Do you need this Use&Care Guide in spanish? Log onto www.askousa.com/customercare to download. Do you need this Use&Care Guide in spanish? Log onto www.askousa.com/customercare to download. ¿Necesita esta Instrucciones de uso y cuidado en español? Entre en www.askousa.com/customercare ¿Necesita esta Instrucciones de uso y cuidado en español? Entre en www.askousa.com/customercare y descárguesela.
Page 4: Important Safety Instructions
Important safety instructions • Clean the lint filter before or after each load. Save these instructions for future reference • Keep the area around the exhaust opening and Installation adjacent surrounding areas free from the accu- mulation of lint, dust and dirt. See the "Installation"...
Page 5: Grounding Instructions
Important safety instructions B) Grounding instructions for a Grounding instructions permanently connected appliance: A) Grounding instructions for a grounded, This appliance must be connected to a grounded cord-connected appliance metal, permanent wiring system, or an equipment- In the event of malfunction or breakdown, grounding conductor must be run with the circuit grounding will reduce the risk of electric shock by conductors and connected to the equipment-...
Page 6: Child Safety
Child safety General Do not allow children to play with the tumble dryer. The tumble dryer does not start automatically when the door closes (for example, if a child closes the door from inside). The tumble dryer has a magnetic catch, which allows the door to be opened from the inside.
Page 7: Description Of The Tumble Dryer
Description of the tumble dryer Panel Outer door Serial number tag and rating plate Fan (behind the front plate) Lint filter holder Lint filter...
Page 8: Front Panel
Front panel Main power switch Options buttons Program selector Display Start/Stop Options button Button for selecting Low Temperature Button for selecting Anti Wrinkle Button for selecting Delayed Start 1-24h...
Page 9: Advice And Tips Before You Tumble Dry
Advice and tips before you tumble dry Here are some tips that may help you before you Materials that should not be tumble begin tumble drying. dried Have the clothes been spun? This symbol means that the material is not suitable for tumble drying.
Page 10: Operating Instructions
Operating instructions Warning! Auto Normal and Auto Delicate These programs shut off the heat once the load To reduce the risk of electric shock or injury to is dry but before it is "bone-dry". The Auto Normal persons, read the "Important Safety Instructions" program shuts off the heat slightly later than Auto section before operating this appliance.
Page 11: Program Chart
Operating instructions Program chart Here we present a few examples of the energy and time consumption of a few different program settings. Consumption can vary due to room temperature, humidity, load, variations in the power supply, and se- lected options For the consumption values given below, the requirements are as follows: Temperature of intake air:...
Page 12: Selecting Options
Operating instructions Delayed Start Selecting Options When you select Delayed Start, the machine will By selecting options, you can tailor drying start 1-24 hours after you press the Start/Stop programs to suit your own laundry require- button. ments. The machine remembers the selected •...
Page 13: Press The Start Button
Operating instructions Press the Start button Drying program finished The text "END" appears on the display Remaining drying time when the program is finished. If the Anti An estimate of the remaining drying time Wrinkle option has been selected, the drum will will be shown on the display a few minutes after rotate for 3 seconds every minute for 2 hours after the drying program starts.
Page 14: Once Drying Has Finished
Operating instructions To install the automatic drain hose, please see the section titled Installation Once drying has finished Turn off the main power switch. Remove the clothes and close the door to prevent small children from climbing into the machine.
Page 15: Care And Maintenance Instructions
Care and maintenance instructions Cleaning the lint filter Cleaning the outside of the machine The lint filter must be cleaned after each load. If Clean the outside of the machine and the program you have very hard water, this can cause panel with a mild cleaner.
Page 16: Troubleshooting
Troubleshooting The machine will not start Overheating cut-off Check The overheating cut-off shuts off the tumble dryer • that the door is properly closed. if the temperature is too high, caused by lint • that the main power switch is on. clogging the lint filter, for instance.
Page 17: Technical Information
Technical information Technical data Height: 33 1/2'' (850mm) Width: 23 7/16'' (595mm) Depth: 23,0" (585mm) Weight: 104lb (47kg) Cylinder volume: 29,3gal (111l) Max. drying capacity: 13lb (6kg) Speed: 52 rpm Rated power: See serial number tag and rating plate. Drum material: Stainless steel Outer casing material: Powder-coated and hot-galvanized sheet steel or...
Page 18: Installation Instructions
Installation instructions A. Freestanding WARNING! The tumble dryer can be positioned beside the washing machine. WARNING - Risk of fire. B. Stacked Install the clothes dryer according to the manufac- The tumble dryer can be placed on top of a ASKO turer's instructions and local codes.
Page 19 Installation instructions C. Built-in ASKO dryers can be installed beneath a cabinet or worktop with a minimum height of 34” (864 mm). There must be a gap of about 1/2” (12 mm) all around the machine, including between the rear edge of the machine top panel and the back wall.
Page 20 Installation instructions How to assemble the stacking kit: 5. Fit the plastic cups so that the "tags" marked 1. Undo the anti-tip device. with arrows are against the front edge or side edge of the cover and press them firmly onto the cover.
Page 21: Adjusting The Feet
Installation instructions To connect the exhaust duct to the rear Adjusting the feet outlet Screw the feet in or out so that the tumble dryer To connect the exhaust duct to the rear outlet, is steady and balanced on the floor or on the follow the steps below:.
Page 22 Installation instructions Connecting the exhaust duct to the Left Connecting to a ventilation duct or Right Side Outlet You will need a UL-CSA-approved, 4-inch ridged To connect the exhaust duct to the left or right metal exhaust duct. If a flexible duct is used, it side outlet, follow the steps below: must comply with the Outline for Clothes Dryer 1.
Page 23: Electrical Installation
Installation instructions To connect the exhaust duct to a Electrical installation ventilation outlet, follow the steps below: Warning! 1. Connect the exhaust duct to a ventilation ex- haust fitting or to a discharge through the wall. The receptacle on the rear of the machine is de- 2.
Page 24 Installation instructions Electrical Connections Connecting a 3-wire Power Cord Warning! Warning! Read the Electrical requirements and grounding Before starting this procedure, be sure the power instructions before connecting the tumble dryer. is turned off at the breaker/fuse box. Electric models of the dryer are manufactured for a 3-wire connection system.
Page 25 Installation instructions 5. Connect ground (center) wire of power supply cord to the center, silver-colored terminal screw. Tighten screw. 6. Connect the other wires to outer screws. 7. Tighten the strain relief screws. 8. Replace terminal box cover on back of dryer. 9.
Page 26: Reversing The Door
Reversing the door 5. Next you must move the plastic plugs on the Reversing the door upper and lower edges of the door. Use a flat The tumble dryer comes with the door hinged on screwdriver. the left. However, it is possible to change the door to be hinged on the right.
Page 27 Reversing the door 14. Replace the screw you removed in step 11. 15. Replace the lower front plate. 9. Insert the cover washer in place of the door magnet. 10. Insert the screws so that the door magnet and cover washer are held in place. 11.
Page 28 Notes...
Page 29 Notes...
Page 30: Quick Guide
Quick guide Fabrics Drying program finished • Dry fabrics of the same type together to • If the Anti Wrinkle option has been select- ensure they dry as evenly as possible. ed, the drum will rotate for 3 seconds every minute for 2 hours after the pro- Turn on the main power switch gram is finished.
Page 31 Service manual TD25 Revision history Revision Date Description Initials 2008-04-28 TD can be speciﬁed with display. Delayed Start 1-24h implemented W723...
Page 32: Type Overview
Service manual TD25 Type overview This type can be speciﬁed with display Temperature Normal dry Extra dry Iron dry Program T 7 1 2 B U T T E R F L Y D R Y I N G Programme: 4 automatic programmes (For further information, see timer diagram at the foot of the document.) Options...
Page 33 Service manual TD25 Programme When using tumble dryer T it is possible to choose between four diﬀerent programmes that automati- cally sense how damp the washing is. The machine dries to diﬀerent levels depending on which of the four programmes has been selected on the front panel. The machine only has one automatic programme that runs for diﬀerent lengths of time (and therefore dries to diﬀerent levels) depending on which of the four pro- grammes has been selected on the front panel.
Page 34: Options And Settings
Service manual TD25 Options and settings Options Means that the drum will rotate 3 seconds per minute for 2 hours once the drying programme has ﬁnished. The option prevents the fabrics from remaining in the same position and becoming creased, which is good if you are unable to remove them immediately after tumble-drying has ﬁnished.
Page 35 Service manual TD25 Settings Possible to set to a high or low temperature. Normal temperature Low temperature Airing dryer: 57°C 43°C Condenser dryer: 73°C 50°C Temperature setting cannot be carried out in the airing programme.
Page 36: Variant Settings
Service manual TD25 Variant settings The following version settings can be made after replacing the control unit. S = Push button L = LED Main power switch J1/S2 Total reset Hold the start/stop button (S1) in, start the machine by pressing the main power switch and keep the start/stop button depressed until one of the LEDs on the panel lights.
Page 37: Test Programme
Service manual TD25 Test programme The entire test programme is run in a sequence as follows. You can cancel the test programme at any time during the programme by opening the door or pressing the main power switch. S = Push button L = LED Main power switch J1/S2...
Page 38 Service manual TD25 Testing the element, thermistor and temperature regulation Press the start/stop button (S1). Indication of faults: • LED L3 starts to ﬂash and the large element loop acti- Fault indication/symp- Cause vates. Press the start/stop button (S1). The element does not Element or cable fault start.
Page 39: Fault Indications
Service manual TD25 Troubleshooting Fault indications The following faults are indicated by a ﬂashing red light in the start/stop button LEDs and as a trouble code on the display (display not available on all machine versions). Fault indication Cause Action LEDs Meaning Display...
Page 40: Other Faults
Service manual TD25 Other faults Fault symptom Cause Action The machine will not start. The outer door is not properly closed. • Check that the door pin is activating the door switch. The machine is not supplied with power. • Check the fuses and connections. The machine stops.
Page 41: Components And Measurement Values
Service manual TD25 Components and measurement values Item number Component Measurement value Comments 80 790 43 Motor 50 Hz, Main winding: 23.8 Ω 220/240 V Auxiliary winding: 28.1 Ω Current: 1.1 A; 270 W; 2850 rpm 80 814 04 Motor 50 Hz, Main winding: 22,9 Ω...
Page 42 Service manual TD25 Item number Component Measurement value Comments Electrical connection The machine is delivered as single phase and can be switched between 1950 W, 10 A and 2500 W, 16 A. Adjustment between 1950 W / 10 A and 2500 W / 16 A is carried out using soft- ware via buttons.
Page 43 Service manual TD25 Technical data Height: 850 mm Width: 595 mm Depth: 585 mm Weight: 47 kg Cylinder volume: 111 l Max. load: 6.0 kg RPM: 52 rpm Rated power: 1950 W = 10 A 2500 W = 16 A Adjustment between 10 and 16 A is carried out using software via buttons.
Page 44: Circuit Diagram
Service manual TD25 Circuit diagram...
Page 45 Service manual TD25 Timer diagram 80 800 48 Rev 02 Service maual TD25 EN...
Page 46 Outer casing T712 US...
Page 48 Lower session T712 US...
Page 50 Cylinder and related parts T712 US...
Page 52 Control panel T712 US...
Page 54 Upper session T712 US...
Page 56 Outer door T712 US...
Page 59 Appd Rev ind Revision Year Week Drawing updated PM 05 44 Drawing updated 05 45 Drawing updated PM 06 09 Drawing updated 08 22 Drawing updated MR 09 02 INKB NTC 2 NTC 1 550 / 1050 W 1950 W Pos.