Jensen Multi-Purpose Speakers CYCLONE II Owner's Manual

Especificaciones CYCLONE II
Respuesta de Frecuencia:
Woofer:
Tweeter:
Sensibilidad:
Impedancia (nominal):
Potencia recomendada
del amplificador:
Manejo de Potencia Máximo:
Tweeter dispersión:
Variación de dispersión:
Frecuencia de Traspaso:
Dimensiones de control
(AlxAnxP):
Peso:
Acabado:
Audiovox Electronics Corporation
©2004 Audiovox Electronics Corporation
All Rights Reserved. All specifications subject to change without notice.
Todos Derechos Reservaron. Todas especificaciones el cambio con sujeción a sin nota.Tous Droits Ont Réservé. Toutes spécifications assujettissent pour changer sans la notification.
55Hz-22kHz ± 3dB
de polipropileno de tira larga de 5
1
de / pulg.- cúpula de plata enfriado
2
de ferrofluido
90dB (2,83v a 1 metro)
4-8 ohmios
10 a 125 vatios
175 vatios
Horizontal 120 ˚ x Vertical 100
hasta 20kHz ± 10
3kHz
5 3 5
9 / x 6 / x 6 / pulg.
8 8 8
5.24 lbs
Negro y Blanco
®
150 Marcus Blvd
Hauppauge, New York 11788
MADE IN CHINA
1
/ pulg.
4
˚
®
#JO-52B/W
Introduction Speaker Mounting
The Jensen CYCLONE II multi-purpose speakers are designed to Note- In some installations, you may find it more convenient
deliver accurate and powerful high fidelity sound in exterior and to make the speaker wire connections described below before
interior applications. The versatile weather-resistant construction placing the speaker in its final location.
makes them ideal for temporary or permanent outdoor use. And
For ease of installation, the Jensen CYCLONE II includes a
the full range of sensitivity and mounting options makes CYCLONE
removable mounting bracket on each speaker. This bracket fea-
II very equally at home in your home.
tures three sets of mounting holes on three different surfaces
allowing you to mount the speaker horizontally, vertically or at a
For simplicity, we'll call your AV receiver, stereo receiver or
45-degree angle. Once mounted, the bracket allows the Jensen
amplifier the receiver.
CYCLONE II to be pivoted to its ideal location. The large thumb
screws (included), when tightened, will hold the selected speaker
IMPORTANT- Do not remove the grilles from your speak-
position. There is also a hex-headed screw molded into the thumb
ers. There are no user serviceable parts behind the grille.
screws. This allows for loosening and tightening by hand or with
Placement Indoors the help of an allen wrench.
Before attempting the installation, carefully evaluate the
The Jensen CYCLONE II can be placed horizontally or vertically in
mounting surface, making sure that its composition and
any convenient location in your room - as stereo pairs on either
construction are strong enough to support the load safely. If you
side of your receiver - as center or surround speakers in home
are unsure about the type of mounting hardware for your
theater surround sound systems that include a subwoofer in your
installation, consult a professional contractor or a knowledgeable
computer room to enhance the multi-media experience - or as
hardware store. The CYCLONE II bracket is suitable only for
remote speakers in a whole house sound system. For installation
attaching the speaker to walls or ceilings constructed of solid
ease in wall and ceiling applications, the included Jensen
wood, brickwork, concrete, hollow building block or wood studs.
mounting brackets can be used.
Do not mount the bracket to unreinforced plaster or sheetrock
(gypsum board). Once the bracket is secure, reattach the speaker
You can experiment with various placements, with the knowledge
using the thumb screws included.
that room acoustics can produce large apparent differences in the
sound for small changes in placement location. For example, Connecting your Speakers
although the speaker may be located at any height above the
floor, locating the tweeter near ear level or angling the entire
Speaker Cable- Typical speaker cable has a pair of
speaker toward ear level, often provides the most realistic
separate speaker wires with insulating jackets that are molded
musical imaging.
together. We recommend you use 18-gauge speaker wire for
hooking your speakers to your receiver.
Another rule to follow is that the amount of bass perceived
Polarity- All speakers in a system must be connected with
increases as you move a speaker closer to intersecting rooms
the same polarity. Speaker wire is marked for polarity so that you
surfaces (walls, ceiling, floor) and that the highest level of bass
can identify the individual wires in the molded pair. Polarity is
results from placement in a corner at the floor or ceiling.
shown by a color stripe on the insulation, by ridges molded into
Placement Outdoors
the insulation, or by the colors of the wires – one copper and one
silver. See Diagram 1.
The Jensen CYCLONE II has been tested for environmental usage
and is weather resistant. Occasional moisture will not
Important- Always connect the red (+) terminal on the
dramatically affect performance. To increase speaker life, mount
receiver to the red (+) terminal on the back of the Jensen
in locations not subject to frequent excessive exposure to water, CYCLONE II, and the black (-) terminal on the receiver to the black
sun and extreme weather. the speakers should be allowed to
(-) terminal on the back of the Jensen CYCLONE II.
ventilate and dry after water exposure.
The Jensen CYCLONE II can be placed permanently outdoors for
year-round enjoyment. Popular locations include decks, gazebos,
porches, atriums, backyards, garages, and spa areas. A
particularly practical mounting location is under the eaves of a
building adjacent to an outdoor recreation area.
For temporary placement, place the speakers in positions that
achieve the most satisfying audio performance to your ear.
to black terminal
(plain or silver)
Switch: Contours the frequency response to compensate for the change in
environmental acoustics between indoors and outdoors.
INDOOR OUTDOOR
3/8"
(9 mm)
bare wire
to red terminal
(color stripe, ridged or copper)