Note For Parts List - Denon DP-200USB Service Manual

NOTE FOR PARTS LIST

1.
Parts for which "nsp" is indicated on this table cannot be supplied.
2. When ordering of part, clearly indicate "1" and "I" (i) to avoid mis-supplying.
3. Ordering part without stating its part number can not be supplied.
4. Part indicated with the mark " " is not illustrated in the exploded view.
5. Not including General-purpose Carbon Film Resistor in the P.W.Board parts list. (Refer to the Schematic Diagram for those parts.)
6. Not including General-purpose Carbon Chip Resistor in the P.W.Board parts list. (Refer to the Schematic Diagram for those parts.)
WARNING:
Parts marked with this symbol z have critical characteristics.
Use ONLY replacement parts recommended by the manufacturer.
Resistors
Ex.: RN 14K
Type Shape
and per-
formance
RD : Carbon 2B : 1/8 W
RC : Composition 2E : 1/4 W
RS : Metal oxide film 2H : 1/2 W
RW: winding 3A : 1 W
RN : Metal film 3D : 2 W
RK : Metal mixture 3F : 3 W
3H : 5 W
Resistance
1 8 2 1800ohm=1.8kohm
Indicates number of zeros after effective number.
2-digit effective number.
1 R 2 1.2ohm
1-digit effective number.
2-digit effective number, decimal point indicated by R.
: Units: ohm
Capacitors
Ex.: CE 04W
Type Shape Dielectric
and per- strength
formance
CE : Aluminum foil 0J : 6.3 V
electrolytic
1A : 10 V
CA : Aluminium solid 1C : 16 V
electrolytic
1E : 25 V
CS : Tantalum electrolytic 1V : 35 V
CQ : Film 1H : 50 V
CK : Ceramic 2A : 100 V
CC : Ceramic 2B : 125 V
CP : Oil 2C : 160 V
CM: Mica 2D : 200 V
CF : Metallized 2E : 250 V
CH : Metallized 2H : 500 V
2J : 630 V
Capacity (electrolyte only)
2 2 2 2200 F
Indicates number of zeros after effective number.
2-digit effective number.
Units: F.
Capacity (except electrolyte)
2 2 2 2200pF=0.0022 F
Indicates number of zeros after efective number.
(More than 2)
2-digit effective number.
Units:pF
When the dielectric strength is indicated in AC,"AC" is included after the dieelectric strength value.
2E 182 G
Power Resist- Allowable Others
ance error
F : 1% P : Pulse-resistant type
G : 2% NL : Low noise type
J : 5% NB : Non-burning type
K : 10% FR : Fuse-resistor
M : 20% F : Lead wire forming
1H 3R2 M
Capacity Allowable Others
error
F : 1% HS : High stability type
G : 2% BP : Non-polar type
J : 5% HR : Ripple-resistant type
K : 10% DL : For change and discharge
M : 20% HF : For assuring high requency
Z : 80%
U : UL part
: - 20% C : CSA part
P : +100%
W : UL-CSA part
C : 0.25pF F : Lead wire forming
D : 0.5pF
= : Others
DP-200USB
FR
BP
2 R 2 2.2 F
1-digit effective number.
2-digit effective number, decimal point indicated by R
Units: F.
2 2 1 220pF
Indicates number of zeros after effective numver.
(0 or 1)
2-digit effective number.
Units:pF
20