Advertisement
Quick Links
Advertisement
Related Manuals for SLEIPNER MOTOR AS RC-11E
Summary of Contents for SLEIPNER MOTOR AS RC-11E
- Page 1 Tel: +47 69 30 00 60 s i d e p o w e r @ s l e i p n e r. n o Fax: +47 69 30 00 70 © Sleipner Motor AS version 1.1 - 2013...
-
Page 2: Table Of Contents
The radio remote control can control a single bow thruster or a bow and stern thruster combined. The receiver can receive the signals of up to four transmitters. Remote control kit (RC-11E) consists of: Receiver: Part no. RCR-1E Transmitter (incl. battery): Part no. RCT-11E Holding bracket for transmitter unit: Part no. -
Page 3: Technical Specifications
Technical specifications Transmitter Receiver Model RCT-11E RCR-1E Power feed 1 x 3V battery (type: CR2032) From thruster Frequency (MHz) 433,2 433,2 Operation temp. -10°C / +55°C -15°C / +55°C HxWxD (mm) 95x48x25 89x68x33 Weight (g) Voltage: 8-30V Load, max Operating range: 15m under normal operating conditions Important precautions •... -
Page 4: Receiver Installation
(RC-EXT) to relocate the antenna. - Above sea level - Away from sources of electrical interference. Note! Faulty installation will render all warranty given by Sleipner Motor AS void. Installation & User Manual, Radio Remote RC11E Page 4... - Page 5 Installation & User Manual, Radio Remote RC11E Page 5...
-
Page 6: Visual Wiring Diagram
Yellow: Automatic main lass down lass down windlass windlass windlass switch (optional) Sleipner Motor AS • Norway Sleipner Motor AS • Norway Sleipner Motor AS • www.side-power.com Sleipner Motor AS • Norway www.side-power.com www.side-power.com www.side-power.com Installation & User Manual, Radio Remote RC11E... - Page 7 Programming additional receivers Push the Pair Button with a plastic stick The original transmitter and receiver have the same factory preset code so that no programming is necessary. When additional transmitters are to be used, the receiver must be programmed again for all transmitters.
-
Page 8: Replacing The Battery
Replacing the battery Battery WARNING: Before working on the transmitter, deactivate the transmitter and the receiver (push “OFF” on the transmitter(s)) and turn off the power to the receiver as well as the thruster mainswitch. 1. Open the transmitter. 2. Take out the battery by inserting a screwdriver or similar between battery and holder at point A, and gently flip the battery out, taking care not damaging the battery grips at point B 3. -
Page 9: User Precautions
Important user precautions • Ensure that you know the location of the main battery switch that disonnects the thruster from all power sources (batteries) so that the thruster can be turned off in case of a malfunction. • If a Side-Power automatic main switch is fitted, the “OFF” button on your transmitter will shut off the main switch providing no other control panels are “ON”. - Page 10 Windlass Remote control “ON” Turn boat to Port Down Turn boat to Starboard Remote control “OFF” Auto-OFF appr. 4 min. Hold for 2 seconds How to use a bowthruster 1. Turn the main power switch for the bow thruster on. Turn on the power to the receiver. 2.
- Page 11 Electric schematics 4-lead & 1-lead connector Bow Thruster Windlass Channel B Channel A External relays for windlass requiring signal output over Coil voltage depend of voltage supply. Output current of relay depend of load form winch last. At least 3 time normal current. Installation &...
- Page 12 Tel:+1 508 995 7000 Tel:+45 4576 3600 Fax:+1 508 998 5359 Fax:+45 4576 1772 www.imtra.com Sleipner Motor AS • P.O. Box 591, N1612 Fredrikstad • Norway www.gertsen-olufsen.dk side-power@imtra.com Tel: +47 69 30 00 60 • Fax: +47 69 30 00 70 info@gertsen-olufsen.dk...
Need help?
Do you have a question about the RC-11E and is the answer not in the manual?
Questions and answers