Related Manuals for SLEIPNER MOTOR AS RCS 20E
Summary of Contents for SLEIPNER MOTOR AS RCS 20E
- Page 1 Installation & User Manual Radio Remote RCS 20E SLEIPNER MOTOR AS P.O. Box 519 N-1612 Fredrikstad Norway w w w . s i d e - p o w e r . c o m Tel: +47 69 30 00 60 s i d e p o w e r @ s l e i p n e r.
-
Page 2: Table Of Contents
Transmitter (incl. battery): Part no. RCT-20E Holding bracket for transmitter unit: Part no. RC-HOLDER Additional transmitters can be ordered separately; Part no. RCT-20E We Sleipner Motor AS declare that this device complies with health and safety requirements according to the Directives EN301 489-3 V1.4.1:2002... -
Page 3: Technical Specifications
Technical specifications Transmitter Receiver Power feed 1x3V battery (type: CR2032) 12V or 24V power source Frequency (MHz) 868MHz 868MHz Operation temp. -10°C / +55°C -15°C / +55°C HxWxD (mm) 107x47x21 110x35x35 Weight (g) Voltage 8-30V Operating range 15m under normal operating conditions Important precautions •... -
Page 4: Receiver Installation
• The receiver is powered by the S-link cable. • Mount the receiver using the four holes (please see picture on page 5). Note! Faulty installation will render all warranty given by Sleipner Motor AS void. Remote Control Receiver S-link... -
Page 5: User Precautions
User precautions • Ensure that you know the location of the main battery switch that disonnects the thruster from all power sources (batteries) so that the thruster/windlass can be turned off in case of a mal- function. • The maximum continues usage time of the electrical thruster is approx. 3 minutes. The electro motor has a built in thermal cut-off switch that will shut it off when overheating and re-engage it when it has cooled down some. - Page 6 RC-20E Bow + Stern thruster Remote control “ON” Turn boat to Port Turn boat to Starboard Remote control “OFF” Auto-OFF appr. 4 min. Hold for 2 seconds How to use a bow/stern thruster 1. Turn the main power switch for the bow/stern thruster on. Turn on the power to the receiver. 2.
-
Page 7: Transmitter Led Operation And Alarm Indication
Transmitter LED operation and alarm indication State LED status Alarm status Transmitter ON The yellow LED’s No sound blink each second Buttons activated The yellow LED’s No sound blink fast Pairing mode All LED’s on No sound Connection lost Red LED is blink- 3 beeps from the ing once each buzzer each second... -
Page 8: Electric Diagram
Electric diagram Installation & User Manual, S-link Radio Remote rev 1_0_0 Page 8... - Page 9 Programming additional receivers Remote Control Receiver S-link LINK/ACT Pair S-link status Pair Button The original transmitter and receiver have the same factory preset code so that no programming is necessary. When additional transmitters are to be used, the additional transmitters has to be paired with the receiver.
-
Page 10: Replacing Transmitter Battery
Replacing transmitter battery Battery WARNING: Before working on the transmitter, deactivate the transmitter and the receiver (push “OFF” on the transmitter(s)) and turn off the power to the receiver as well as the thruster mainswitch. 1. Open the transmitter case by removing the 3 torque screws. 2. -
Page 11: Dimensions
Dimensions Designed b olekr Copyright NS-ISO 2768-1 Over t.o.m. f ±0,05 ±0,1 ±0,2 - ±0,05 ±0,1 ±0,3 ±0,5 ±0,1 ±0,2 ±0,5 ±1 ±0,15 ±0,3 ±0,8 ±1,5 120 400 ±0,2 ±0,5 ±1,2 ±2,5 400 1000 ±0,3 ±0,8 ±2 ±4 1000 2000 ±0,5 ±1,2 ±3 ±6 2000 4000 - ±2... - Page 12 Tel: +47 69 30 00 60 Fax:+47 69 30 00 70 www.side-power.com sidepower@sleipner.no The information given in the document was correct at the time it was published. However, Sleipner Motor AS can not accept liability for any inaccuracies or omissions it may contain.
Need help?
Do you have a question about the RCS 20E and is the answer not in the manual?
Questions and answers