SERVICE MANUAL FTD-G931AS FTD-G931AS/BK THESE DOCUMENTS ARE FOR REPAIR SERVICE INFORMATION ONLY.EVERY REASONABLE EFFORT HAS BEEN MADE TO ENSURE THE ACCURACY OF THIS MANUAL; WE CANNOT GUARANTEE THE ACCURACY OFTHIS INFORMATION AFTER THE DATE OF PUBLICATION AND DISCLAIMS RELIABILITY FOR...
BUFFALO FTD-G931AS/BK 2.LCD MONITOR DESCRIPTION The LCD MONITOR will contain an main board, an inverter/power board, an audio board, keypad board which house the flat panel control logic, brightness control logic and DDC. The power board will provide AC to DC Inverter voltage to drive the backlight of panel and the main board chips each voltage.
BUFFALO FTD-G931AS/BK 3. OPERATING INSTRUCTIONS 3.1 GENERAL INSTRUCTIONS Press the power button to turn the monitor on or off. The other control buttons are located at front panel of the monitor. By changing these settings, the picture can be adjusted to your personal preferences.
BUFFALO FTD-G931AS/BK 3.3 ADJUSTING THE PICTURE Steps: 1.Press MENU button to display OSD main menu, Press Left button or Right button may select other main Menu. 2. Press MENU button to adjust items of each main menu. 3. Press Left button or Right button may select item you wish to enter.
Page 8
BUFFALO FTD-G931AS/BK Main Menu Item Sub Menu Item Sub Menu Icon Description Auto Auto adjust color Recall Color Temperature from Color Temp EEPROM Color Red Setting Red Gain from Digital-register Green Setting Green Gain from Digital-register Blue Setting Blue Gain from Digital-register...
BUFFALO FTD-G931AS/BK 5. SOFTWARE FLOW CHART 1. Initialize MCU settings, including I/O, Timer, ISR and Serial Port settings. 2. Read EEPROM content to recover monitor settings, including brightness, contrast, color temperature and OSD position etc. 3. Initialize system variable, including system flag, OSD timeout counter, burin mode status…...
BUFFALO FTD-G931AS/BK 7.Trouble Shooting 7.1 Main board No power No power Press power key and look if the picture is normal Please reinsert and make sure the AC of 100-240 is normal Reinsert or check the power section Measure U201 PIN2=1.8V U202 PIN2=3.3V...
Page 17
BUFFALO FTD-G931AS/BK No picture The button if under control Check X601 oscillate Correspondent waveform is normal component. Measure U202 PIN2=3.3V Replace U601 U201 PIN2=1.8V Check Correspondent component X401 oscillate waveform is normal Check Correspondent component. Replace U401 White screen...
BUFFALO FTD-G931AS/BK White screen Measure Q204 base is high level? Measure U202 PIN2=3.3V U201 PIN2=1.8V Check Q203 is broken Check Correspondent or CN503 solder? component X401 oscillate waveform is normal Check Correspondent component Check Correspondent component Replace PANEL Replace U401 7.2 PWPC board...
Page 19
BUFFALO FTD-G931AS/BK No power Check AC line volt 110V or 220V Check AC line Check the voltage of C905(+) Check F901, bridge rectified circuit Check start voltage for the pin3 of IC901 Check R906, R907, IC901 Check the auxiliary voltage is between 10V-16V...
Page 20
BUFFALO FTD-G931AS/BK Check F902 Check D201/Q209/Q210 Check D202/Q211/Q212 Check ON/OFF signal Check Interface board Check U201 pin9=12V voltage Change Q201 or Q202 Check the pin10/Pin7 of U201 have saw tooth Short Q203/Q204 if the picture normal Replace U201 Connect PIN15 of U201 to the ground and check...
BUFFALO FTD-G931AS/BK 9.BOM LIST The different parts of T980KA4NJSB1A & T980KA4NJSB2A Part No. for TPV Description Quantity Unit TPV model 34G1276 Y 4L BACK COVER T980KA4NJSB1A 34G1276 GM 4L BACK COVER T980KA4NJSB2A 40G 191894 1A ID LABEL T980KA4NJSB1A 40G 191894 2A...
Page 32
BUFFALO FTD-G931AS/BK 40G 58162435A LABEL 40G 581689 4A SERIAL LABEL FOR MONITO 40G 581894 2A BLUE DOT 41G7800894 4A INSTALL MANUAL 44G3231 15 EVA WASHER 44G3231 15506 EVA WASHER 44G3910 5 U TYPE SHEET 44G3920 1 EPS(L) 44G3920 2 EPS(R)