1. Manuals
  2. Brands
  3. JBM electronics Manuals
  4. Gateway
  5. C-130
  6. Quick start manual

JBM electronics C-130 Quick Start Manual

Jbm electronics hub/switch quick start guide c-130
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
C-130
Quick Start Guide
Page -1-
Copyright ©2007 JBM Electronics, Inc.

Advertisement

Table of Contents
loading

Related Manuals for JBM electronics C-130

Summary of Contents for JBM electronics C-130

  • Page 1 C-130 Quick Start Guide Page -1- Copyright ©2007 JBM Electronics, Inc.

  • Page 2: Table Of Contents

    Quick Start Guide ... 3 Unpacking Instructions ... 3 Preparation ... 3 Accessing the Graphical Management Interface ... 4 Step 1: Connect PC to JBM Gateway ... 4 Step 2: Setup PC IP Address ... 5 Step 3: Access JBM Webserver ... 8 Step 4: Log into the Graphical Administration Utility (GAU) ...

  • Page 3: Quick Start Guide

    Quick Start Guide Unpacking Instructions 1. Unpack the C130. 2. Verify the following components are enclosed 3. If any items are missing, please contact JBM at 1-800-489-7781. Preparation Verify that you have one of the following, supported cellular cards: (Figure 1xRTT/1xEVDO Audiovox/UTSStarcom: 5740 Kyocera: KPC-650...

  • Page 4: Accessing The Graphical Management Interface

    ETH1. Verify the link LED is lit. (Crossover cable for HUB/Switch). Port Straight (ETH0) Straight (ETH0) Crossed (ETH1) Crossed (ETH1) Cable Device Straight HUB or Switch Crossed Straight Crossed HUB or Switch Page -4- Copyright ©2007 JBM Electronics, Inc.

  • Page 5: Step 2: Setup Pc Ip Address

    Note: This example shows cabling to a PC. The link LED is not lit for ETH1. Without a link LED lit either Method 1 must be used or the cabling must be checked. Step 2: Setup PC IP Address Set the PC’s IP Address by going to control panel and selecting network connections, the screen below will appear: •...
  • Page 6 NOTE: The screens and instructions displayed are based on Windows XP. Your system may be different. If you have any problems contact your system admin. • Scroll down to the bottom of the following items and select “Internet Protocol (TCP/IP)” (as shown to the left).
  • Page 7 METHOD 2: PC to ETH1 • Select “Use the following IP address” and fill in the blank fields with the information below: • • Subnet mask: • Default gatewa:y • Preferred DNS: • Click “OK” • The previous screen will appear Click “OK” Verify that the IP change was accepted or acquired on the PC.

  • Page 8: Step 3: Access Jbm Webserver

    • METHOD 1 should display an IP of 192.168.0.2 • METHOD 2 should display an IP of 192.168.1.2 Step 3: Access JBM Webserver • Open a web browser and enter the following in the address bar: METHOD 1: METHOD 2: Step 4: Log into the Graphical Administration Utility (GAU) JBMgateway Login Instructions User Name enter: jbmadmin ( lowercase letters)

  • Page 9: Cellular Card Configuration

    Cellular Card Configuration Your JBM Gateway is able to detect many cellular cards, but others must still be configured manually. If you are using either one of the older 1xRTT/CDMA cards, or a GPRS/EDGE/HSDPA card that requires the use of a userid, password, and APN, you will need to configure your car manually, as covered in the next section.
  • Page 10 Step 1: Cellular Carrier Selection • Select the cellular carrier you are using from the drop-down menu. Page -10- Copyright ©2007 JBM Electronics, Inc.
  • Page 11 • Select the Aircard you are using: Page -11- Copyright ©2007 JBM Electronics, Inc.

  • Page 12: Step 2: Set The Userid, Password And Apn

    Step 2: Set the Userid, password and APN • If you are using a GPRS, Edge, or HSDPA based card, enter the userid, password, and APN that was provided by your cellular carrier. This information should have been packaged with your card. If you do not have this information please contact your carrier account representative or the carrier’...

  • Page 13: Cellular Connectivity Troubleshooting

    Note: Depending on the provisioning of your card, particularly in corporate applications in which the JBM Gateway is providing cellular backup connectivity to wired circuits, your card may be restricted from Internet access. If this is the case, you may want to instead test to insure that you are able to access your corporate network.

  • Page 14: Verifying Ip Connectivity

    Verifying IP Connectivity First, let’s check to make sure that you card is connecting to the cellular network and obtaining an IP address. Navigate to the GAU screen shown below: If your screen looks similar to the one shown above, you are having signal reception difficulties.

  • Page 15: Minimal Reception

    Minimal Reception On occasion, you can find yourself in a situation where you have just enough signal to be able to communicate with the cellular tower, and obtain an IP address, but not enough reception to be able to sustain a viable connection. If your cellular card is using dynamically assigned IP addresses, you can determine if you are in a situation like this by watching the “Current Interface Address”...

  • Page 16: Jbm Technical Support

    Re-verify your userid, password, and APN information. Be sure to pay close attention, as all three of these items are case specific and must be entered exactly in order to properly log into the cellular network. Don’t forget to click “Save” and “Apply” if you make any changes. JBM Technical Support If you have followed all of the instructions up to this point, have satisfied yourself that you are not having an authentication problem, are convinced that you have sufficient...

  • Page 17: Specifcations

    Power: Yellow – Power Connection Status (PWR) Ethernet Ports: Green – LAN Connection Status (LINK) RED – Data Transmit Activity Status (T) ON-OFF-ON (Flickering) Green – Data Receive Activity Status (R) ON-OFF-ON (Flickering) RS232 Ports: Green – Data Receive Activity Status (RD) (Async) ON-OFF-ON (Flickering) Red –...

  • Page 18: Fcc Compliance Statement

    Software Licensing Terms and Conditions Software supplied with each JBM Electronics' product remains the exclusive property of JBM Electronics. JBM grants with each unit a perpetual license to use this software with the express limitation that the software may not be copied or used in any other product for any purpose.

  • Page 19: Warranty

    Warranty JBM Electronics provides a limited hardware warranty for the Gateway, which consists of the following: • This warranty is effective for one year from the delivery date of the Gateway to the purchaser. • The purchaser is responsible for returning the defective unit to our factory, freight prepaid.

Table of Contents