Advertisement
Quick Links
Advertisement
Related Manuals for JBM electronics 900
Summary of Contents for JBM electronics 900
- Page 1 Gateway Installation Manual...
- Page 2 Specifications described in this manual are Revision Level: 5.0 Revision Date: 1/3/2004 © Copyright 2004 by JBM Electronics Co. For further information, contact: JBM Electronics Co. 4645 LaGuardia St. Louis, MO 63134 (314) 426-7781 Fax: (314) 426-0007 Website: http://www.jbmelectronics.com © JBM Electronics Co. NOTICE subject to change without notice.
- Page 3 JBM Electronics' Gateways are low-cost routers designed for users who need to interface Legacy protocol devices to a Frame Relay network. The Gateway 900 (G900) provides one serial port, a 10/100BaseT port and a WAN port with an integrated T1/E1 DSU...
- Page 4 Gateway 900 Installation Manual Page 2 Benefits The Gateway simplifies network design by eliminating the need for network changes to handle Legacy protocols. The conversion eliminates the need for a separate network for the legacy protocol and protects the investment in Legacy devices when moving to an IP network.
- Page 5 Gateway 900 Installation Manual Page 3 Diagnostics The Gateways can be configured through Application Commands entered via Telnet interface. The Telnet connection provides command and control of the Gateway. SNMP Traps provide notification of major events in the Gateway. All of the protocol-specific diagnostics, such as LUSTATS, Notify, and Status and Sense Bytes are supported.
- Page 6 Gateway 900 Installation Manual The Gateways can be ordered with Frame Relay connections using an internal or external DSU. The Gateway 700 provides the same port configuration as the G900 but uses an external DSU. The Gateway 800 provides an integrated 56/64/72 KB DSU. With the frame connection, the Gateways provide a complete router replacement with full protocol conversion.
- Page 7 Cables The Setup and Operations Manuals are on the CD supplied with the Gateway. Remove the JBM Electronics Gateway 900 from the shipping carton. Inspect the Gateway for shipping damage. If any damage is found, retain the carton and contact the carrier.
- Page 8 Gateway 900 Installation Manual AVERTISSEMENT: Points d’accès RJ-45. Ceux-ci sont protégés par des prises de données. Ils ne peuvent pas êntre utilisés comme prises de téléphone conventionnelles standard, ni pour la connection de l’unité à un réseau téléphonique central privé ou public. Raccorder seulement connecteurs de données RJ-45, systèmes de réseaux de téléphonie ou téléphones...
- Page 9 Gateway 900 Installation Manual Operation The Gateways are designed for unattended operation. The Gateways can be controlled through the Console Port (Port 5) or via Telnet (if the Gateway’s IP Address is known). The connection provides access through a variety of Application Commands.
- Page 10 Gateway 900 Installation Manual The Gateway will display the Login Screen. Once this screen is displayed, Log in to the Gateway using root for the user name and gateway for the password. These entries are case sensitive and must be entered in the appropriate case.
- Page 11 Gateway 900 Installation Manual Configure the WAN interface Instructions for configuring the WAN interface are available through the console: Readme.config (configuring IP over frame) Wanpipe Configuration.pdf (general overview) Wanpipe Configuration Before starting WANPIPE, a configuration file (wanpipeN.conf, where N=1,2,3..etc.) must be created in /etc/wanpipe directory.
- Page 12 Gateway 900 Installation Manual For the rest of this document, we will assume we are working with the following ISP/Telco supplied data: Protocol: Frame Relay Prot Info: Num of DLCI's = 2 DLCI=16 and 17 IP Info: LCI 16 Local =201.1.1.1 PtoP Netmask =255.255.255.0...
- Page 13 Gateway 900 Installation Manual This example is Frame Relay with two DLCIs. The first input is: "Please specify the number of DLCIs supported on this Frame Relay connection" Enter in number 2 For each network interface do the following: DLCI Number: Enter in the DLCI number. Note the default number is always Interface Name: The Interface name will also have default value.
-
Page 14: Color Function
Gateway 900 Installation Manual Thus if errors occur, first check /var/log/messages to find out what exactly went wrong with the drivers startup. Once the device is started you should see a "link connecting" message. This message indicates that the card was been configured successfully and that the link is trying to connect. - Page 15 Gateway 900 Installation Manual Gateway 900 Specifications Serial Port: Baud Rate: Interface: WAN Port: Baud Rate: Interface: LAN Port: Ethernet: Console Port: Baud Rate: Interface: Management: Console Port: IP Protocol LED Indicators: Serial Port(s): WAN Port: LAN Port: Power: Power:...
-
Page 16: Safety Information
Gateway 900 Installation Manual SAFETY INFORMATION Please read the following safety information carefully before installing the Gateway. WARNING: Installation and removal of the unit must be carried out by qualified personnel only. The unit must be connected to an earthed (grounded) outlet to comply with international safety standards. -
Page 17: L'information De Sécurité Importante
Gateway 900 Installation Manual The supply plug must comply with BS1363 (3-pin 13-amp) and be fitted with a 5 A fuse which compiles with BS1362. The main cords must be <HAR> or <BASEC> marked and be of type HO3VVF3G0.75 (minimum). - Page 18 Le cordon secteur doit porter la mention <HAR> ou <BASEC> et doit être de type H03VVF3GO.75 (minimum). Technical Information Related Standards The Gateway 900, 905 and 910 have been designed to the following standards: FCC PART 15, SUBPART B, Class A CISPR 22/EN 55022, Class A IEC 61000-4-2/EN 61000-4-2...
- Page 19 Gateway 900 Installation Manual Information To The User If this equipment does cause interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient the receiving antenna.
- Page 20 Gateway 900 Installation Manual Except for the express warranty set forth herein, JBM Electronics Co. grants no warranties, either express or implied, of merchantability and fitness. The stated express warranty is in lieu of all liabilities or obligations of JBM Electronics Co. for damages including but not limited to consequential damages occurring out of or in connection with the delivery, use or performance of JBM products.