Cross Technologies 2097-07 Instruction Manual

Advertisement

Quick Links

Instruction Manual
CROSS TECHNOLOGIES,
INC
MGC
AGC MGC
Data, drawings, and other material contained herein are proprietary to Cross Technologies, Inc.,
but may be reproduced or duplicated without the prior permission of Cross Technologies, Inc.
for purposes of operating the equipment. Printed in USA.
When ordering parts from Cross Technologies, Inc., be sure to include the equipment
model number, equipment serial number, and a description of the part.
GND AGC
DC
C
T
ROSS
ECHNOLOGIES, INC.
6170 Shiloh Road
Alpharetta, Georgia 30005
(770) 886-8005
FAX (770) 886-7964
Toll Free 888-900-5588
WEB: www.crosstechnologies.com
E-MAIL: info@crosstechnologies.com
Model 2097-07
2097 AMPLIFIER
Amplifier
April 2010 Rev B

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the 2097-07 and is the answer not in the manual?

Questions and answers

Summary of Contents for Cross Technologies 2097-07

  • Page 1 AGC MGC Data, drawings, and other material contained herein are proprietary to Cross Technologies, Inc., but may be reproduced or duplicated without the prior permission of Cross Technologies, Inc. for purposes of operating the equipment. Printed in USA. When ordering parts from Cross Technologies, Inc., be sure to include the equipment model number, equipment serial number, and a description of the part.
  • Page 2: Table Of Contents

    All Cross Technologies, Inc. products are warranted against defective materials and workmanship for a period of one year after shipment to customer. Cross Technologies, Inc.’s obligation under this warranty is limited to repairing or, at Cross Technologies, Inc.’s option, replacing parts, subassemblies, or entire assemblies. Cross Technologies, Inc. shall not be liable for any special, indirect, or consequential damages.
  • Page 3: Model 2097-07 Amplifier

    -35 dBm ±10 dB output. The 2097-07 has a band limiting lowpass filter and automatic gain (AGC) or manual gain (MGC) for a -80 to 0 dBm input range. The 2097-07 is powered by a 120 VAC IN, +15 VAC OUT, unregulated, wall power supply and is housed in an 4.7”...
  • Page 4: Installation

    DC Voltage from 0 to -2 volts, 1K impedance, In (MGC) use R40 to adjust the gain. increases as the gain increases in AGC only. Figure 2.2 2097 Front Panel Controls and Indicators 2097-07 Manual, Rev. B Page 4 04/26/10...
  • Page 5 J1 - 70 MHz IN The 50 MHz IF input. This is at a 0 to -80 dBm level. This is a 50 , SIGNAL SIGNAL BNC, female connector. Figure 2.3 2097 Rear Panel Inputs and Outputs 2097-07 Manual, Rev. B Page 5 04/26/10...
  • Page 6: Installation/Operation

    6.) To check proper operation and adequate signal level, monitor TP3, TP4 with a voltmeter. 2.4.2 AGC Voltage Relating to Gain - The 2097-07 operates over a 0 to -80 input. In Automatic Gain (AGC) with S1 to AGC, the gain is adjusted automatically to provide a constant -35 ±10 dBm output level over the entire 0 to -80 dBm input.
  • Page 7: Environmental Use Information

    G. Top Cover - There are no serviceable parts inside the product so, the Top Cover should not be removed. If the Top Cover is removed the ground strap and associated screw MUST BE RE-INSTALLED prior to Top Cover screw replacement. FAILURE TO DO this may cause INGRESS and/or EGRESS emission problems. 2097-07 Manual, Rev. B Page 7 04/26/10...
  • Page 8: Cross Technologies, Inc

    ROSS ECHNOLOGIES, INC. 6170 Shiloh Road Alpharetta, Georgia 30005 (770) 886-8005 FAX (770) 886-7964 Toll Free 888-900-5588 WEB www.crosstechnologies.com E-MAIL info@crosstechnologies.com 2010 Printed in USA • 2097-07 Manual, Rev. B Page 8 04/26/10...

Table of Contents