Advertisement
o
Removal of Ghasis from Cabinet
1. Remove 6 screws from le{t and right sides of cabinet.
2. Separate cabinet from chassis.
3. Remove 18 screws from bottom of cabinet.
4. Remove 4 screws from Leg.
5. Separate bottom of cabinet from chassis.
Removal of Front Panel Assembly
1 . W i t h A l l e n w r e n c h r e m o v e T u n i n g a n d V o l u m e K n o b s .
2. Remove all Knobs and Lever switches f rom panel.
3. Remove 2 screws from top of panel.
4. Remove 2 screws from bottom of panel.
5. Remove nut from "Function" and "Speaker" switches
located on Front Panel Assembly.
6. Separate Front Panel Assembly from chassis.
Removal of Slide Rail Pointer
1 . R e m o v e M e t a l S l i d e P o i n t e r f r o m S l i d e R a i l P o i n t e r .
2. Remove 3 screws from top of Slide Rail Pointer.
3. Remove 2 screws from left and riqht sides of Slide Rail
P o i n t e r .
Removal of Meter
1. Remove One screw and Meter Cover.
2 . U n s o l d e r l e a d s f r o m m e t e r t e r m i n a l s .
3 . G r a s p M e t e r f i r m l y a n d p u l l b a c k s e p a r a t i n g M e t e r f r o m
o a n e l .
Removal of AM-FM Stereo Function Indicator Lamps
1. Grasp base of lamp with long-nosed Pliers and Carefully
extract from grommet holder.
2 . U n s o l d e r A M - F M I n d i c a t o r L a m o f r o m P . C . B o a r d .
Removal and Replacement of Dial Lampc
1. Remove 4 plastic screws from top of Dial P.C. Board.
2. Grasp Dial Lamp and extract from lamp grommet
h o l d e r .
Removal of Front End from Chassis
1 . U n s o l d e r l e a d s f r o m F r o n t E n d t e r m i n a l .
2. Unscrew 2 screws from Drum. (Do Not Remove Dial
S t r i n g F r o m D r u m . )
3. Remove 4 screws from insides of Front End. (Do Not
Remove 4 screws From Outsides Of Front End Case.)
Testing and troubleshooting any of the P.C. boards does
not require removal since all iomponent parts are top board
mounted. For underneath board inspection purposes or
r - r i , : , , = . i e i , : ; i ; ; l
: : : i ^ i p a l c a r
i s : , - ' i - , r n s n l , l c r ; J
a n { 1
replaced, the P.C. board can be sufficiently turned over
by only removing the hold down hardware. Where it neces-
sitates complete removal of any individual board then
oroceed as follows.
DISASSEMBLY INSTRUCTIONS
Remoual of AM-FM RF/lF/TtlPX Amp P.C. Board
1. Urisolder wire wraps from terminals.
2. Remove 4 screws from P.C. Board.
3. Slide P.C. Board from plastic clip.
Removal of Multi Path and Dolby P.C. Board (RS-1080
Only)
1. Unsolder wire wraps from terminals.
2. Remove 4 hold down screws.
Removal of EO-Amp P.C. Board
1. Unsolder wire wraos from terminals.
2. Remove 4 Hold down screws.
3. Grasp P.C. Board and extract from Shield Case.
(Do Not Remove Shield Case From Chassis.)
Removal of Protector P.C. Board
1 . U n s o l d e r w i r e w r a p s f r o m t e r m i a n l s .
2. Remove 4 hold down screws.
Removal of Volume lnd and Volume P.C. Board
1 . W i t h A l l e n w r e n c h r e m o v e V o l u m e I n d P . C . B o a r d f r o m
V o l u m e S h a f t .
2 . R e m o v e O n e n u t h o l d i n g V o l u m e P . C . B o a r d .
3 . U n s o l d e r w i r e w r a o s f r o m t e r m i n a l s .
Removd of Pre Amp P.C. Board
1. Remove 14 screws from 7 Lever Switches.
2 . U n p l u g 2 c o n n e c t o r s .
3 . U n s o l d e r w i r e w r a p s f r o m t e r m i n a l s .
Removal of Tone Control Amp P.C. Board
1. Remove 3 hold down nuts from Tone Control P.C.
Board.
2 . U n p l u g 2 c o n n e c t o r s .
Removal of Low Range P.C. Board
1. Remove 2 hold down nuts from Low Range P.C. Boarcj.
2. Unplug One connector.
Removal of Porver Supply P.G. Board.
'l
. Remove 2 screws releasing clip holding P.C. Board.
2. Grasp P.C. Board firmly and extract from plug. (Do
Not Remove Plug From Chassis.)
Removd of Porver Amp P.C. Board
r Please refer to Exploded View on Page 8.
..
I
I
- 5 -
Advertisement
