Table of Contents
Advertisement
• Replacement of the supply cord. If the supply cord is damaged, it must be
replaced by the manufacturer or an authorised D
to avoid a hazard.
Extension Cords
CAUTION: Use only extension cords that are approved by the country's Electrical
Authority. Before using extension cords, inspect them for loose or exposed wires,
damaged insulation and defective fittings. Replace the cord if necessary.
MINIMUM GAUGE FOR CORD SETS
For Cable length (m): 7.5
15
Use Cable with minimum rating (Amperes)
Tool Amperes
0 - 3.4
7.5
7.5
3.5 - 5.0
7.5
7.5
5.1 - 7.0
10
10
7.1 - 12.0
15
15
12.1 - 20.0
20
20
Additional Specific Safety Rules for Reciprocating Saws
• Hold power tool by insulated gripping surfaces, when performing an operation
where the cutting accessory may contact hidden wiring. Cutting accessory
contacting a "live" wire may make exposed metal parts of the power tool "live"
and could give the operator an electric shock.
• Use clamps or another practical way to secure and support the workpiece to
a stable platform. Holding the work by hand or against your body leaves it
unstable and may lead to loss of control.
• Hold saw firmly with both hands for all cutting operations. During cutting
operations, the blade may suddenly bind in the work and may cause the saw to
kickback towards the operator.
• Keep hands away from moving parts. Never place your hands near the cutting
area.
• Use extra caution when cutting overhead and pay particular attention to
overhead wires which may be hidden from view. Anticipate the path of falling
branches and debris ahead of time.
WALT Service Centre in order
E
current rating of 30mA or less.
the following standards:
25
30
45
60
7.5
7.5
7.5
7.5
other construction activities contains chemicals known to cause cancer, birth defects
7.5
7.5
10
15
or other reproductive harm. Some examples of these chemicals are:
10
10
15
15
15
15
20
20
20
20
25
–
Your risk from these exposures varies, depending on how often you do this type of
work. To reduce your exposure to these chemicals: work in a well ventilated area, and
work with approved safety equipment, such as those dust masks that are specially
designed to filter out microscopic particles.
serious and permanent respiratory or other injury. Always use NIOSH/OSHA approved
respiratory protection appropriate for the dust exposure. Direct particles away from
face and body.
AS/NZS1270 during use. Under some conditions and duration of use, noise from this
product may contribute to hearing loss.
3
• Do not operate this tool for long periods of time. Vibration caused by the
operating action of this tool may cause permanent injury to fingers, hands, and
arms. Use gloves to provide extra cushion, take frequent rest periods, and limit
daily time of use.
WARNING: We recommend the use of a residual current device with a residual
WARNING: ALWAYS wear approved protective safety equipment complying with
• Eye protection: AS/NZS1337 Eye Protectors for Industrial Applications;
• Hearing protection: AS/NZS1270 Acoustics – Hearing Protection;
• Respiratory protection: AS/NZS1716 Respiratory Protective Devices.
WARNING: Some dust created by power sanding, sawing, grinding, drilling, and
• lead from lead-based paints,
• crystalline silica from bricks and cement and other masonry products, and
• arsenic and chromium from chemically-treated lumber.
• Avoid prolonged contact with dust from power sanding, sawing, grinding,
drilling, and other construction activities. Wear protective clothing and wash
exposed areas with soap and water. Allowing dust to get into your mouth, eyes,
or lay on the skin may promote absorption of harmful chemicals.
WARNING: Use of this tool can generate and/or disburse dust, which may cause
WARNING: Always wear proper personal hearing protection that conforms to
Hide quick links:
Advertisement
Table of Contents
