Panasonic DVD-S100 Operating Instructions Manual page 19

No picture
Pictures not in progressive output.
Closed captions not displayed.
Sound incorrect
Sound distorted.
Piercing noise comes from the
speakers.
Effects do not work.
No sound
Recording
Cannot record to digital
recording equipment.
(Incorrect sound recorded.)
Unit displays
"NOPLAY"
"U11"
"H∑∑"
∑∑ stands for a number.
"NODISC"
"U70-∑"
∑ stands for a number.
The actual number following "U70-"
will depend on the state of this unit.
TV displays
"/"
"Cannot play group xx, content xx"
"Cannot play title xx, chapter xx"
"Cannot display group xx, content xx"
"Cannot play audio"
"No audio"
"Check the disc"
"Due to copyright protection,
audio cannot be output from
HDMI"
While "HDMI Status" displayed,
any items are not underlined.
"This disc may not be played in
your region"
No on-screen display.
"Authorization Error"
"Rental Expired"
≥When AUDIO ONLY is on, video and audio cannot be output from HDMI AV OUT terminal. Press
[AUDIO ONLY] again.
≥If the unit is connected to the TV through VIDEO OUT or S VIDEO OUT terminal output will be
interlace.
≥When progressive output or HDMI output is on, closed captions will not be displayed.
≥Set "Advanced Surround" in Audio Menu to "Off".
≥Set "Attenuator" in Audio Menu to "On" if it causes distortion with 2 ch or 5.1 ch AUDIO OUT connections.
≥Noise may occur when playing WMA.
≥[DVD-A] The disc may have restrictions on the method of audio output. With some multi-channel
discs, unless the number of connected speakers is the same as the disc's channel specification,
audio will not be output properly. Refer to the disc's jacket for more information.
≥With HDMI AV OUT connections, audio may not be output from other terminals in the way that was set.
≥Match the speaker settings with the connected equipment.
≥If you have connected a digital amplifier which does not include decoder, be sure to select "PCM"
in "Dolby Digital" or "DTS Digital Surround" in "Audio" menu.
≥None of the audio effects work when the unit is outputting bitstream signals from the
OPTICAL or HDMI AV OUT terminal.
≥Some audio effects do not work or have less effect with some discs.
≥Dolby Pro Logic II, Night Sound Mode, H.Bass, Advanced Surround, Multi Re-master and Sound
Enhancement do not work if you have changed the play speed.
≥ With HDMI AV OUT connections, Dolby Pro Logic II does not work.
≥AUDIO ONLY does not work when EZ Sync is set to "On".
≥Audio may not be heard when more than 4 devices are connected with HDMI cables. Reduce the
number of connected devices.
≥When AUDIO ONLY is on:
– Audio may not be output depending on the type of TV.
– Video and audio cannot be output from HDMI AV OUT terminal. Press [AUDIO ONLY] again.
≥There may be a pause in sound when you change the play speed.
≥[DivX] Audio may not be output due to how files were created.
≥You cannot record WMA/MP3.
≥You cannot record DVDs that have protection preventing digital recording.
≥You cannot record DVDs if the recording equipment cannot handle signals with a sampling frequency of 48 kHz.
≥Make the following settings:
– Advanced Surround:
– PCM Digital Output:
– Dolby Digital/DTS Digital Surround:
≥You inserted a disc the unit cannot play; insert one it can.
≥You inserted a blank disc.
≥The disc may be dirty.
≥You inserted a disc that has not been finalized.
≥Trouble may have occurred. The number following "H" depends on the status of the unit. Turn the unit off
and then back to on. Alternatively, turn the unit off, disconnect the AC power supply cord, and then
reconnect it.
≥If the service numbers fail to clear, note the service number and contact a qualified service person.
≥You haven't inserted a disc: Insert one.
≥You haven't inserted the disc correctly: Insert it correctly.
≥The HDMI connection acts unusually.
– The connected equipment is not HDMI compatible.
– The HDMI cable is too long.
– The HDMI cable is damaged.
≥The operation is prohibited by the unit or disc.
≥You are trying to play incompatible items.
≥Audio has not been recorded, or recorded in a format this unit cannot playback. Video playback
only is possible.
≥This disc may be dirty.
≥Should you connect equipment that does not support CPPM (➜ 20, Glossary), the audio from the
CPPM copy protected DVD-Audio cannot be output from HDMI AV OUT terminal. Connect the
audio cable of the Audio/Video cable (L, R) to a HDMI compatible AUDIO IN terminal.
≥If you select an item without "¢" in the "Video Output Mode" in Picture Menu, it will not be
underlined.
≥You can only play DVD-Video if their region number is "1", "ALL" or multiple region numbers
including "1".
≥Select "On" in "On-Screen Messages" in "Display" menu.
≥You are trying to play the DivX VOD content that was purchased with a different registration code.
You cannot play the content on this unit.
≥The DivX VOD content has zero remaining plays. You cannot play it.
Off
Up to 48 kHz
PCM
9
–
–
14
14
–
–
–
16, 17
16
COAXIAL, –
–
8, 14
–
9, 16
–
–
9
8
20
–
–
–
14
16
16
4
–
4
4
–
–
–
7
–
–
–
–
–
–
4
5
13
Cover
16
11
11
19
19