1. Manuals
  2. Brands
  3. Lampo Manuals
  4. Power Supply
  5. IP65
  6. User manual

Lampo IP65 LED User Manual

Ip65 led power supply
Hide thumbs Also See for IP65 LED:
Table of Contents

Advertisement

Quick Links

Download this manual
L L
E E
D D
P P
O O
W W
E E
R R
r
g
b
r
g
b
L
E
D
P
O
W
E
R
r
g
b
I I
P P
6 6
5 5
L L
E E
D D
p p
o o
w w
e e
r r
s s
u u
p p
p p
l l
y y
I
P
6
5
L
E
D
p
o
w
e
r
s
u
p
p
l
y
USER' S MANUAL release 2.0
This manual must be considered an integral part of the projector.

Advertisement

Table of Contents
loading

Related Manuals for Lampo IP65 LED

Summary of Contents for Lampo IP65 LED

  • Page 1 USER’ S MANUAL release 2.0 This manual must be considered an integral part of the projector.

  • Page 2: Table Of Contents

    BEFORE CONNECTING AND USING LED POWER RGB, IT IS IMPORTANT TO READ CAREFULLY ALL THE INSTRUCTIONS IN THIS MANUAL. QUALIFIED PERSONNEL ONLY, IN COMPLIANCE WITH ALL THE SECURITY LAWS, CAN DO THE INSTALLATION, THE MAINTENANCE AND THE UTILISATION OF THIS POWER SUPPLY. BEFORE CONNECTING LED POWER RGB, MAKE SURE THAT THE FREQUENCY AND THE VOLTAGE VALUES ARE SUITABLE AS SPECIFIED ON THE POWER SUPPLY.

  • Page 3: Dimensions And Weight

    Dimensions & weight = 1,9 Kg Technical data IP65 protection rate Aluminium body with silicone gasket Ideal for out-door, can be installed in any position Input voltage range: from 85Vac to 265Vac. Frequency: 50-60 Hz 0,95 PFC electronically controlled Can drive up to 36LEDs (RGB) or 48 LEDs (RGB+W or RGB+A) at 350mA On request it is possible to use 700mA controlled current 4 independent LEDs groups: 12 Red, 12 Green, 12 Blue and 12 White or Amber Electronic board 8/16 bit resolution with 4 digit display...

  • Page 4: Installation

    Installation Led Power RGB can be installed in any positions. Attention, the IP65 protection rate does not allow to install the unit in places that can be flooded (for example under-ground box) The base of Led Power RGB has 4 blind holes. Open this holes if necessary.

  • Page 5: Signal Cable Selection

    Signal cable selection Use only shielded and twisted cables with EIA485 (RS485) standards. The cable must be low capacity and with an impedance between 82 and 120 ohm. It is preferable not to use audio cables. The wire size we recommend is 26 AWG or higher. If the projector have cable clamps, the external diameter of cable must be compatible with cable clamps.

  • Page 6: Power Supply Connection

    Always, use Male XLR 3 or 5 pin connector to connect the projectors to the DMX controller. Solder on PIN 1 of the XLR connector the shield of the signal cable, on PIN 2 solder the negative (example: black wire of cable) and on PIN 3 solder the positive (example: red or white wire of the cable).

  • Page 7: Dmx Signal Connection

    DMX signal cable connection For fixed installation it is better to connect signal cables IN/OUT directly to the terminal connection block with the cable going through the PG9 cable clamps. The cable’s diameter must be compatible with the cable clamps of the projector (PG9), diameter from 4 to 7mm. Pin 1: GND, shield Pin2 : signal - Pin3 : signal +...

  • Page 8: Cable Wiring With Rj45

    USING CABLE WITH RJ45 AND HUB It is possible to connect a 4 couples cable to the dedicated terminal connection block (LEDs) and terminate it with an RJ45 female plug. This way you can use UTP cables with RJ45 cat.5 connectors and special HUB RJ45 for “T” junction. The projectors are connected in series and LED HUB in junction box.

  • Page 9: Schematic Menu

    Schematic menu Following the list of menu and submenu.

  • Page 10: User's Interface

    User’s interface Use inside display interface to modify setting of the projector: change DMX starting address, enable stand alone function. Use the buttons + and - to surf the menu’s function. To enter into the menu, you have to push the Mode button and after that you can search for the desiderate function and push the Enter to enter in it.
  • Page 11 (leds state when DMX signal isn’t received). When the board is switched on and DMX signal is missing, the board DM.ST: can do this functions: black-out, leds on at 15% or led on at 100%. Default value 15.ON Go to this submenu pushing Mode , choose DM.ST with + and - and push Enter . Use + and - to select the desiderate value and push Enter to confirm: 15.ON, (15% ON) r,g,b,a channels ON at 15% A.ON, (ALL ON) r,g,b,a channels ON at 100%...

  • Page 12: Dmx Control Mode

    (temperature) When NTC is connected, you can see heater’s temperature in Celsius degrees. The board has an TEMP: automatic control over the led’s power, so the leds are always under the safety temperature. Go to this submenu pushing Mode , choose TEMP with + and - and push Enter to enter in. Push Mode to get out of this function.
  • Page 13 CHANNEL 6: STROBE This channel sets the parameters of the strobe effect. On the following table you have the dmx values, the strobe frequency (flash speed) and the strobe hold. Strobe frequency Strobe light hold Strobe frequency Strobe light hold DMX value DMX value (Seconds)
  • Page 14 0,17 0,84 1,51 0,18 113 to 114 0,85 1,52 0,19 0,86 1,53 From 33 to 34 0,20 0,87 1,54 From 199 to 0,21 0,88 1,55 0,22 0,89 1,56 From 119 to 0,23 0,90 1,57 0,24 0,91 1,58 From 39 to 40 0,25 0,92 From 204 to...
  • Page 15 Dimmer mode, one channel: CHANNEL 1: DIMMER to control the dimmer of all the leds, from max power to OFF. DMX value function Led at max Power From 1 to 254 Proportional light output decrease Led OFF Three colours mode: CHANNEL 1: GREEN, to control the light output of the green leds, from OFF to the Max Power.
  • Page 16 Four colours mode: CHANNEL 1: GREEN, to control the light output of the green leds, from OFF to the Max Power. DMX value function Led OFF From 1 to 254 Proportional Light output increase Led at max power CHANNEL 2: RED, to control the light output of the red leds, from OFF to the Max Power. DMX value function Led OFF...
  • Page 17 Advanced mode, 16bit colour resolution: 13C d CHANNEL 1: GREEN, to control the light output of the green leds, from OFF to the Max Power. DMX value function Led OFF From 1 to 254 Proportional Light output increase Led at max power CHANNEL 2: GREEN fine, 16bit regulation of green leds DMX value function...
  • Page 18 1,16 0,15 0,16 0,05 1,04 0,14 0,15 0,05 0,92 0,14 0,14 0,05 0,80 0,14 0,13 0,04 0,76 0,13 0,12 0,04 0,72 0,13 0,10 0,04 0,68 0,12 0,09 0,04 0,64 0,12 Da 50 a 54 0,08 0,04 0,60 0,11 Da 55 a 60 0,07 0,04 0,56...

  • Page 19: Spare Parts

    CHANNEL 12: FADE SPEED This channel allows the users to force a fade time (from 0s to 0,5s) to the speed of the r,g,b,a,dimmer channels. This function is very helpful for use the flash button of many consolle. DMX value function NO FADE From 1 to 255...
  • Page 20 Lampo Lighting Designers s.r.l., via Portogallo 4, 46042 Castel Goffredo (MN), ITALY This information only applies to customers in the European Union, according to directive 2002/96/EC of the European parliament and of the council of 27/gen/2003 on waste electrical and electronic equipment (WEE) and legislation transposing and implementing it into the various national legal systems.

This manual is also suitable for:

Led power rgb

Table of Contents