Disassembly - Sony DCR-DVD301 Service Manual

The following flow chart shows the disassembly procedure.

2-1. DISASSEMBLY

3
B
1
B
B
2
1 Open the jack cover
2 Two EG grip Screws (M1.7x4) black
3 EG grip Screw (M1.7x4) black
1
3
A
4
A
2
1 Two EG grip screws (M1.7x4) black
2 Two EG grip screws (M1.7x4) black
3 Six claws
4 P cabinet C assembly
B
1
2
B
3
1 Turn over the EVF section in the
1 Four EG grip Screws
direction of the arrow.
2 EG grip Screw (M1.7x4) black
2 Three claws
3 Three EG grip Screws (M1.7x4) black
3 Remove the cabinet (R) section
in the direction of the arrow.
4 FP-073 flexible board (33P)
5 Cabinet (R) section
B
A
Screw Screw
M1.7x4 M1.7x4
3-078-893-21 3-087-376-01
C D
Silver
Tapping screw
Screw
M1.7x5
M1.7x2.5
3-081-204-21 Black
3-078-889-11
DCR-DVD301
2. DISASSEMBLY
1
B
2
1 Open the LCD panel.
2 EG grip Screw (M1.7x4) black
1
3
2
Note: Be very careful not to
1 Two claws
damage the flexible board.
2 MA-429 board (27P)
3 F panel section
Note:
Be very careful not to
damage the flexible board.
2
3
5
B
4
B
(M1.7x4) black
1
1
C
1 Two screws (M1.7x2.5) silver
2 CK radiation sheet (885),
CK cushion (885)
3 Harness (PV-019) (20P)
2-1
HELP 01
3
1 Screw (M1.7x2.5) silver
2 EG grip screw (M1.7x4) black
3 FP-883 flexible board (10P)
4 FP-889 flexible board (20P)
5 EVF section
2
5
IC Radiation
sheet (135)
4
VC-354 board
1 Three screws (M1.7x2.5) silver
(Side B)
2 Control switch block (PS8700) (20P)
3 Board to board (CN1007, CN4901) (100P)
4 VC-354 board
5 Radiation sheet (135)
CK radiation sheet (885)
Note:
Don't be re-used.
CK cushion
(885)
6
3
2
4
A
1 Two EG grip screws (M1.7x4) black
2 Two EG grip screws (M1.7x4) black
5
3 Six claws
4 FP-911 flexible board (16P)
4 P cabinet C assembly
5 Two EG grip screws (M1.7x4) black
5 Two EG grip screws (M1.7x4) black
6 LCD section
6 Harness (PV-019) (20P)
5
B
2
C
4
1
1 Sheet (IM)
2 Three screws (M1.7x2.5) silver
3 FP-892 flexible board (39P)
4 From lens flexible board (29P)
5 Lens section
3
4
- 3 5
V C
C
1
2
9
b
8
q;
4
1
A
- 2 4
P D
1
3
2
6
A
A
7
5
7 Hinge (885) assembly, Hinge (885)cover C,
Hinge cover (rear), Harness (PV-019).
8 Control switch block (BL8700) (6P)
9 P cabinet M (885)
q; PD-241 board, LCD unit (ACX531AK-J),
Light guide plate block
2-2
Lens electrostatic sheet (885)
Note:
Don't be re-used.
5
3
C
2
1
4
Sheet (IM)
7
3
See page
B
2-3.
4
C
6
1
C
2
5
D
1 Screw (M1.7x2.5) silver
2 Front fixed plate
3 EG grip screw (M1.7x4) black
4 Screw (M1.7x2.5) silver
5 Two tapping screws (M1.7x5) black
6 Claw
7 Remove the cabinet center (M)
assembly in the direction of the arrow.
1 Push this portion with a finger
in the direction of the arrow a.
a
2 Open the D lid assembly
in the direction of the arrow b.
1