200hz lcd tv signature series in full hd, premium series in full hd, true cinematic series, modern classic series, sleek & stylish series, home theatre systems, portable dvd players (2 pages)
WAX2F RM-ED008 SERVICE MANUAL WAX2F CHASSIS MODEL MODEL COMMANDER DEST COMMANDER DEST KDL-40W2000 KDL-40W2000 RM-ED008 RM-ED008 KDL-46W2000 KDL-46W2000 RM-ED008 RM-ED008 KDL-40W2000 / KDL-46W2000 RM-ED008 FLAT PANEL COLOR TV - 1 -...
THE SCHEMATIC DIAGRAMS, EXPLODED VIEWS AND IN THE 3-4-5. White Balance of colour temperature “Warm2” PARTS LIST ARE CRITICAL FOR SAFE OPERATION. REPLACE THESE COMPONENTS WITH SONY PARTS WHOSE PART 3-5. Panel Replacement ..........NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS PUBLISHED BY SONY.
Due to the higher melting point of Lead Free Solder the soldering iron tip temperature needs to be set to 370 degrees centigrade. This requires soldering equipment capable of accurate temperature control coupled with a good heat recovery characteristics. For more information on the use of Lead Free Solder, please refer to http://www.sony-training.com - 3 -...
Inputs for RGB. (KDL-46W2000 without stand) (CENELEC standard) Outputs of Video and Audio signals (Selectable). SmartLink interface. Approx 27.5kg (KDL-40W2000 with stand) Approx 23.0kg (KDL-40W2000 without stand) Weight Approx 36.0kg (KDL-46W2000 with stand) Approx 30.0kg (KDL-46W2000 without stand) RM-ED008 Remote Commander (1)
Page 5
WAX2F RM-ED008 KDL-40W2000 KDL-40W2000 Model Name KDL-46W2000 KDL-46W2000 Item (AEP) (UK) RGB Priority Sub Woofer Scart 1 Scart 2 Front in (6) Projector Norm B/G Norm I Norm D/K Norm AUS Norm L Norm SAT Norm M Teletext Nicam Stereo WARNING (UK Models only) The flexible mains lead is supplied connected to a B.S.
Page 6
WAX2F RM-ED008 21 pin connector Pin No Signal Signal level Audio output B Standard level : 0.5V rms (right) Output impedence : Less than 1kohm* Audio input B Standard level : 0.5V rms (right) Output impedence : More than 10kohm* Audio output A Standard level : 0.5V rms (left)
WAX2F RM-ED008 WAX2F SELF DIAGNOSTIC SOFTWARE The identification of errors within the WAX2F chassis is triggered in one of two ways :- 1: Busy or 2: Device failure to respond to IIC. In the event of one of these situations arising the software will first try to release the bus if busy (Failure to do so will report with a continuous flashing LED) and then communicate with each device in turn to establish if a device is faulty.
(Top screw removed with rear cover) Arm VESA (46) R Assy (KDL-46W2000) Arm VESA (46) R Assy (KDL-46W2000) VESA Bracket (40) R Assy (KDL-40W2000) VESA Bracket (40) R Assy (KDL-40W2000) Arm VESA (46) L Assy (KDL-46W2000) Arm VESA (46) L Assy (KDL-46W2000)
WAX2F RM-ED008 2-7. BE and FEE BOARD REMOVAL Six screws Six screws BE board BE board Four screws Four screws FEE board FEE board 2-8. G2A BOARD REMOVAL Four screws Four screws G2A board G2A board – 22 –...
Cover, button Cover, button Two screws Two screws H1E board H1E board Button, multi Button, multi 2-10. H2E or H46 BOARD REMOVAL H2E(KDL-40W2000) or H46 Board(KDL-46W2000) H2E(KDL-40W2000) or H46 Board(KDL-46W2000) Holder, Side Jack (L) Holder, Side Jack (L) – 23 –...
WAX2F RM-ED008 SECTION 3 SET-UP ADJUSTMENTS 3-2. Signal Level Adjustment 3-1. How to enter Service Mode Service adjustments to this model can be performed using the 3-2-1. Set up of AD calibration1 adjustment for supplied remote Commander RM-ED008. terrestrial analog. The following adjustments are done via ECS.
WAX2F RM-ED008 3-2-4. C signal calibration1 adjustment for 3-2-7. Set up of C signal calibration1 adjustment terrestrial analog. for video. 1. Send ECS_ADJUST_TCD3_HUE_RF command. 1. Input PAL colour bar 75%Y, 75%C via AV1 input. 2. Read S-REG: READ_BACK_B00 via ECS. (READ_AREA=0). 2.
WAX2F RM-ED008 2. Send ECS_ADJUST_TCD3_CONT_V command. 3-3-2. Set up Trident internal SG and brightness 3. Read the value of S-REG:APL_LUMA via ECS. Confirming that measurement the value is within spec of the table below. 1. Ensure TEST_PATTEN_ON=1. 2. Ensure TEST_G_LEVEL=204. 3.
WAX2F RM-ED008 7. Set up TEST_G_LEVEL=153. b). Adjustment value of R_GAMMA_OFST_05=<128. 8. Adjust R_GAMMA_OFST_04 and B_GAMMA_OFST_04 · chroma values so that they are within tolerance in the table below. R_GAMMA_OFST_06 = R_GAMMA_OFST_07 =R_GAMMA_OFST_04. Tolerance c). Adjustment value of B_GAMMA_OFST_05=<180. 40" 0.1924 0.4272 0.7JND...
WAX2F RM-ED008 4. Set up TEST_G_LEVEL=51 and adjust R_BKG and B_BKG 3-5. Panel Replacement values to within the spec of the table below. When replacing the panel please reset the gamma and white balance before performing W/B (See page 27, 3-4) for new panel. Spec.
TUNER SCL (TUN) VOUT SILENT SDA SDA (TUN) nTV-DEM SEL SILENT SCL 1.8V 3.3V AS TUN AS (TUN) QSDA (KDL-40W2000) CN3904 AGC DEFEAT TUN AGC (TUN) SDA-ANA TV DEM SEL CVBS-TUNER CVBS TUNER CN1201 V2 IN C SILENT SDA R-AUDIO-QSS...
~ AE Printed Wiring Board Conductor Side A ~ ~ AE Board IC Voltage Table Side A ~ Ref No Pin No Volts (V) Ref No Pin No Volts (V) Ref No Pin No Volts (V) Ref No Pin No Volts (V) Ref No Pin No...
Page 39
~ AE Printed Wiring Board Conductor Side B ~ - 39 -...
Page 58
FEE.-WAX2F(KDL-40/46W2000) FB3600 C3608 C3600 C3604 +3V3D NOTE: THESE ARE THE TWO SCREW A SIDE B SIDE CONNECTIONS TO THE GND ISLAND CN3610 +3V3D R3612 R3618 FB3601 NEAR END OF CI CONNECTOR. CN3604 R3613 R3619 THIS ISLAND IS GROUNDED VIA THE R3614 R3620 +3V3D...
~ FEE Printed Wiring Board Conductor Side A ~ ~ FEE Board Semiconductor Voltage Table Side A ~ ~ FEE Board Semiconductor Location Table Side A ~ DIODE IC3206 C - 2 IC3403 A - 3 IC3501 D - 2 D3400 F - 4 IC3100...
~ G2A Printed Wiring Board Conductor Side A ~ ~ G2A Board Semiconductor Location Table Side A ~ DIODE D6305 I - 9 D6000 C - 8 D6306 H - 10 D6103 H - 5 D6506 D - 4 D6200 J - 2 D6201 M - 2...
Page 62
~ G2A Printed Wiring Board Conductor Side B ~ ~ G2A Board Semiconductor Location Table Side B ~ DIODE D6507 K - 3 D6000 K - 8 D6508 K - 3 D6002 G - 10 D6509 L - 3 D6003 G - 9 D6510 L - 2...
~ H1E Printed Wiring Board Conductor Side A ~ ~ H1E Printed Wiring Board Conductor Side B ~ ~ H2E Printed Wiring Board Conductor Side A ~ ~ H2E Printed Wiring Board Conductor Side B ~ ~ H3E Printed Wiring Board Conductor Side A ~ ~ H3E Printed Wiring Board Conductor Side B ~ ~ H46 Printed Wiring Board Conductor Side A ~ ~ H46 Printed Wiring Board Conductor Side B ~...
~ TUE Printed Wiring Board Conductor Side A ~ ~ TUE Board Semiconductor Location Table Side A ~ TRANSISTOR IC3900 G - 3 Q3901 G - 2 Q3903 F - 2 ~ TUE Board Semiconductor Voltage Table Side A ~ ~ TUE Board IC Voltage Table Side A ~ ~ TUE Printed Wiring Board Conductor Side B ~ ~ TUE Board Semiconductor Location Table Side B ~...
The construction parts of an assembled part are indicated be anticipated when ordering these items. with a collation number in the remarks column. 5-1. REAR COVER AND STAND ASSEMBLY Revision 2.0 (Click inside red box to see related change) UK MODELS ONLY REF.NO. PART.NO DESCRIPTION REMARK REF.NO. PART.NO DESCRIPTION REMARK X-2149-932-1 STAND ASSY (ML) (KDL-40W2000) 2-5 2-580-640-01 SCREW, +BVTP2 4X16 X-2149-690-1 STAND ASSY (L) (KDL-46W2000) 2-664-636-11 COVER, ECS 2-675-191-02 FOOT X-2148-134-1 COVER, REAR ASSY (40) (KDL-40W2000) 2-580-647-01 SCREW, +KTP2 4X12 X-2148-135-2 COVER, REAR ASSY (46) (KDL-46W2000) 2-689-628-01 SCREW, (B) 5X30 10 £...
AE BOARD COMPLETE Parts List : ....................98 H1E BOARD COMPLETE Parts List : ....................105 H2E BOARD COMPLETE Parts List : (KDL-40W2000)................105 H3E BOARD COMPLETE Parts List : ....................106 MISCELLANEOUS : ....................107 ACCESSORIES AND CONNECTORS : ....................