Related Manuals for Seiko I Infotech LP-1020
Summary of Contents for Seiko I Infotech LP-1020
- Page 1 U00107692700 Quick Reference Guide Black-and-White Raster Plotter LP-1020 LP-1020L Network Multi Function Plotter LP-1020-MF LP-1020L-MF...
-
Page 2: Table Of Contents
Introduction Thank you for purchasing our LP-1020/LP-1020L Black-and-white Raster Plotter and LP- 1020-MF/LP-1020L-MF Network Multi-Function Plotter. This manual explains the basic operations of LP-1020/LP-1020L and LP-1020-MF/LP- 1020L-MF. For details, refer to the respective PDF data saved in CD-ROM. The DSCAN format described in this manual as well as DSCAN that appears on the operation display are for only customers in Japan. -
Page 3: Lp-1020/Lp-1020L
● Names and functions of each part LP-1020/LP-1020L Front / right side/rear side Toner cover Finished drawing outlet Control panel Manual feed drawer (door 4) Waste toner door Roll 1 drawer (door 1) Roll 2 drawer (door 2) Top cover (door 6) -
Page 4: Control Panel
Control panel ➁LCD ➃Power key ➀LEDs ➂Keys Number Name Function Indicates the presence or absence of errors. Error lamp (red) On: Error present Off: No error present Indicates the amount of remaining toner. On: There is sufficient toner. Toner lamp (green) Flashing: Toner is running low. -
Page 5: Turning The Power On And Off
● Turning the power on and off LP-1020/LP-1020L Power on Turn on the Main power switch located at the Press the power key located on the control lower-left as seen from the rear of the device. panel of this device (when the main power switch is on). -
Page 6: Set Menu
● Set menu LP-1020/LP-1020L Menu structure Press to set the device offline before performing setting operations. Select a menu using the keys and press the key to enter each menu. Changed parameters are saved in non-volatile memory and are not lost when the power is turned off. - Page 7 Menu Item Function Device POWER SAVE Sets the time until the device enters the power saving mode. Sets the data standby time to automatically have the paper roll end cut EDGE CUT TIMER before plotting using data received after a data standby status has continued for a while.
-
Page 8: How To Set The Paper Rolls
● How to set the paper rolls LP-1020/LP-1020L Replacing paper rolls ◆How to detach the paper rolls Detach and replace a paper roll when the device has run out of paper rolls or when you change the paper roll size on type. - Page 9 ◆How to attach the paper roll Load the paper into the drawer. Hold the paper roll so that the end of the paper is positioned at the bottom facing the back of the device. ◆ The paper flange ends do not have a Then align the paper flange to the depressions in the designated right or left side.
- Page 10 Caution Note ◆ After closing the paper roll drawer, wait until the ◆ Take care not to hurt yourself and damage the “WAIT A MOMENT” message disappears before device when handling the cutter. ◆ Handle the cutter blade with care so that you do opening the paper roll drawer again.
-
Page 11: Troubleshooting
● Troubleshooting LP-1020/LP-1020L Paper jam If a paper jam occurs, the ERROR lamp lights and the According to the paper jam point, the door number from which following error message appears on the LCD. the corrective measure starts is displayed (plural numbers may be displayed as shown left). - Page 12 Symptom and corrective measure ◆Items to be checked Symptom Items to be checked Corrective measure Power cable connection Plug the power cable into the outlet correctly. No power Power supply to the outlet Supply the power to the outlet. Failure to start or ERROR lights and LC Take appropriate measures according to the error message.
-
Page 13: Lp-1020-Mf/Lp-1020L-Mf
● Names and functions of each part LP-1020-MF/LP-1020L-MF Front / right side/rear side Control panel Scanner exit guide Finished drawing outlet Manual feed drawer (door 4) Waste toner door Roll 1 drawer (door 1) Roll 2 drawer (door 2) Top door (door 6) - Page 14 Control panel WARNING LIGHT POWER MENU COPY PRINT MEMORY RESET POWER SAVING DELIVERY FILE REPRINT STOP SCAN STOP ORIGINAL ORIGINAL BACKGROUND SCALE x1 SIZE TYPE REMOVAL DENSITY WASTE PAPER TONER AUTO TEXT/LINE TONER FEED PROCESS DARK MANUAL FEED FIXED SCALE FIXED-SIZE ORIGINAL TEXT/PHOTO...
- Page 15 Name Function Indicates the process cartridge replacement time. On: Normal. [PROCESS] LED Flashing: Replacement timing is approaching. Off: Process cartridge is not installed. Indicates whether the paper to be fed manually has been set. [MANUAL FEED] LED On: Paper has been set. Off: No paper.
-
Page 16: Turning The Power On And Off
● Turning the power on and off LP-1020-MF/LP-1020L-MF Power on Turn on the Main power switch located at the Press the power key located on the control lower-left as seen from the rear of the device. panel of this device (when the main power switch is on). -
Page 17: Set Menu
PRINT mode Press the [MENU] key during stand-by or in the PRINT mode and enter OFLINE. The menu message will appear. The setup method and setting items are the same as those of LP-1020/LP-1020L. Refer to page 4. COPY mode ◆Copy function overview... -
Page 18: Basic Operation
DELIVERY mode ◆Delivery function overview ◆Delivery function In the DELIVERY mode of the device, the scanned data can Function list Description be saved in the delivery host computer connected via network, Original Size Sets the original size. or the data can be transferred to other computers on the same network. - Page 19 See “User's Guide, Copy part” for the delivery operation. Input the original. Input the original to the device. Press the [START] key. Press the [START] key. If the SCAN START or ORIGINAL SET has been set in the system menu, the copy/delivery starts automatically without pressing the [START] key.
-
Page 20: How To Input An Original/Routine Maintenance
● How to input an original/Routine maintenance LP-1020-MF/LP-1020L-MF How to input an original ◆ Butt the original against the front roller and Adjust the position of the original width guide. give it a slack, so Roller Slack that the original... - Page 21 ◆Removing original width guide Remove the scanner exit guide. If the return of the original is changed between front and rear exit frequently, remove the original width guide in advance. Hook your finger on the claw at the bottom and while opening the claw, pull towand you, and the original width guide will be removed.
- Page 22 Wipe the shading guide and scanner glass with a dry cloth. If extremely dirty, use the cloth dampened with water or neutral Scanner glass detergent diluted with water and then wrung dry. Replacing paper rolls Paper roll replacement is the same as that of LP-1020. Refer to page 6.
-
Page 23: Troubleshooting
● Troubleshooting LP-1020-MF/LP-1020L-MF Copy/scan cannot be performed clearly Streaks appear in the copy/scan result Dust attaches to background. • The shading guide or scanner glass is • The BACKGROUND REMOVAL is set to dirty. smaller value. ➝Clean the shading guide or scanner glass (⇒... -
Page 24: Maintenance
● Maintenance Panel messages used in this manual refer to those used in LP-1020/LP-1020L. Kanji is also used in LP-1020-MF/LP-1020L-MF to improve the ease of reading messages. Replacing the toner cartridge When there is no more toner availabe, the Toner lamp will go Note ◆... - Page 25 Close the scanner cover. Set the toner cartridge into the main unit. (for LP-1020-MF only) While supporting the scanner cover with your right hand, release the stopper in the middle with your left hand and close the scanner cover slowly.
- Page 26 Close the scanner cover and attach the cover. scanner exit guide. At this time, the following message appears on the (for LP-1020-MF only) LCD. WA I T A MOMEN T Replacing the waste toner bottle When the waste bottle becomes full with waste toner, the Note Waste toner lamp will go out.
- Page 27 When you have removed the waste toner bottle, the Attach a new waste toner bottle. LCD will display the following message. 1Insert the mouth of the waste toner bottle onto the waste toner discharge port of the main unit by slightly S E T lifting it.
- Page 28 Note Place a new Process cartridge on the top ◆ Until you are ready to install the Process of the device. cartridge, do not unpack it and store it in its 1Remove the Process cartridge from the box together cardboard container. with its protective case.
- Page 29 Insert the Process cartridge. Replace the filter. To insert the Process cartridge, align the Process Pull out the filters toward you and remove, and replace cartridge with the angle of the open top cover and insert with the two filters contained in the process cartridge it in the direction of the alignment arrows (three points/ packaging box.
- Page 30 Durch die Kennzeichnung dieses Produktes mit dem CE-Zeichen erklärt Seiko den folgenden Direktiven der Europäischen Union zu entsprechen (mit Wirkung vom siehe Datum): Januar 1996:- EG-Direktive 73/23/EEC ergänzt durch EG-Direktive 93/68/EEC, Angleichung der Gesetze der...
Need help?
Do you have a question about the LP-1020 and is the answer not in the manual?
Questions and answers