1. Manuals
  2. Brands
  3. Speco Manuals
  4. Server
  5. ONSIP OS101
  6. User manual

Speco ONSIP OS101 User Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
User's Guide
ONSIP OS101
ONSIP OS101

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the ONSIP OS101 and is the answer not in the manual?

Questions and answers

Related Manuals for Speco ONSIP OS101

Summary of Contents for Speco ONSIP OS101

  • Page 1 User’s Guide ONSIP OS101 ONSIP OS101...
  • Page 2 Do not disassemble ONSIP OS101. You will be excluded from After Service when disassembled. Use only the power adapter provided with the ONSIP OS101. If you would like to use the ONSIP OS101 for security, monitoring, please check the legal regulations within the country.
  • Page 3 ONSIP OS101 User’s Guide Caution Any changes or modifications to this device could void the warranty. Revision History Date Rev No Description 2011-11-01 First manual revision creation. Rev.1.0 (Nov., 2011)

  • Page 4: Table Of Contents

    ONSIP OS101 User’s Guide Table of Contents 1. Introduction ..............................5 1.1. Overview ..........................5 1.2. Specification ........................6 1.3. Applications of ONSIP OS101 ..................8 2. Product Description ............................. 9 2.1. Contents ..........................9 2.2. Preview ..........................10 2.3. Physical description ......................11 2.3.2.

  • Page 5: Introduction

    IP connection over internet or intranet. The ONSIP OS101 is easy to install and owner will experience cost and space savings in the installation owing to the state of the art technologies embedded in the system. Based on Embedded Software Solution (Embedded Web Server, Embedded Streaming Server, Network Protocol), the ONSIP OS101 ensures unprecedented performance and stability to be an ideal video server solution for system integration solutions.

  • Page 6: Specification

    ONSIP OS101 User’s Guide 1.2. Specification Category Sub-Category Details Compression H.264/MJPEG NTSC (30 frames/sec Max.) : 704x480, 640x480, 704x240, 352x240, 176x112 Video Resolution PAL/SECAM (25 frames/sec Max.) : 704x576, 640x480, 704x288, 352x288, 176x144 Audio 32 Kbps G.726 (Bi- Down 64 Kbps PCM...
  • Page 7 ONSIP OS101 User’s Guide ID and Password protection IP filtering for restricting administrative access for audio and bi-audio Sync to PC Synchronize to PC Manual Manual time setting Time management Internet Time Synchronize to Time Server Server Day light saving...

  • Page 8: Applications Of Onsip Os101

    ONSIP OS101 User’s Guide 1.3. Applications of ONSIP OS101  Security surveillance (buildings, stores, manufacturing facilities, parking lots, banks, government facilities, Military etc.) • Real time Internet broadcasting • Remote monitoring (hospitals, kindergartens, traffic, public areas, etc.) • Teleconference (bi-directional audio conference) •...

  • Page 9: Product Description

    ONSIP OS101 User’s Guide 2. Product Description 2.1. Contents Open the package and check if you have the followings: Components Description Remarks ONSIP OS101 ONSIP OS101 Video server 12VDC adaptor Power adapter Built in standard PoE (IEEE 802.3af) (Optional item)

  • Page 10: Preview

    2.2. Preview CMS Software IP-Installer ONSIP OS101 (Speco-NVR) PC software to view and record the PC software to allocate an IP H.264 1CH Video Server A/V streaming data transmitted from address to the ONSIP OS101 ONSIP OS101 Rev.1.0 (Nov., 2011)

  • Page 11: Physical Description

    ONSIP OS101 User’s Guide 2.3. Physical description 2.3.1. External View Figure 2-1. External view of ONSIP OS101 2.3.2. Front & Rear View Figure 2-2. Front view Figure 2-3. Rear view Rev.1.0 (Nov., 2011)

  • Page 12: Functional Description

    ONSIP OS101 User’s Guide 2.4. Functional Description Section Description Remarks RJ-45 Power over Ethernet (IEEE802.3af) 10/100Base-T 12VDC In Adapter 5W (A/V Server) + Max 25W (Camera) 0.5A ~ 2.5A 12VDC Out Dependent Adapter Max 25W (Adapter minus 5W) capacity of the adapter...
  • Page 13 Figure 2-4. Power cable for analog came Caution: If ONSIP OS101 is powered by PoE, do not plug in DC Jack with active DC power into DC power input connector.  CVBS, Y/C Video In: Connect conventional analog video signal.
  • Page 14 ONSIP OS101 User’s Guide  CVBS Out (BNC/BALUN): Support to connect external monitor. Simultaneous connection is not allowed.  Factory Default Switch There is a switch provided for returning the video server to factory default state. Press th e switch through a tiny hole located below 100BaseT connector using a tool with sharp tip for a few seconds while power is applied.
  • Page 15 Power Supply Supply Figure 2-4. SENSOR input of ONSIP OS101  RLY (Relay) OUT A Relay output is provided for connecting alarm devices or remote on/off control of device such as light. Relay circuit is normal open and circuit is closed upon alarm output or rem ote on.

  • Page 16: Getting Started

    3. Getting Started 3.1. PC Requirement AV streaming data received from ONSIP OS101 can be decoded or stored in a PC running Speco- NVR program which is a viewing & recording program for a PC. Minimum requirement of the PC is...

  • Page 17: Quick Installation Guide

    (PC is needed to assign IP address to ONSIP OS101) In case of using PoE, connect the PC and ONSIP OS101 to the network using one of the following ways. If your LAN Switch does not support standard PoE, connect ONSIP OS101 as shown in dotted line in Figure 3-1.
  • Page 18 ONSIP OS101 User’s Guide Install Speco-NVR Speco-NVR is a multi-channel CMS program for to IP camera or Video server. Install Spec o-NVR on remote PC to connect to these products. It is needed to assign connection infor mation to Speco-NVR program before connection. Insert the CD provided with product int o the PC and install the Speco-NVR.
  • Page 19 ONSIP OS101 User’s Guide Click on the field in ③ for sorting and rearranging the list. Select network mode that best suits from the drop down list in ⑤. You can choose either Static or ADSL and Auto (DHCP), respectively. If ADSL and Auto are selected, the fields in ⑥...
  • Page 20 Remote video connection to ONSIP OS101 Connection through Web Viewer Web Viewer offers simplest way of video connection to ONSIP OS101. For video connection, enter the IP address of ONSIP OS101 in the URL field of Internet Explorer as: omitted [e.g.] Port 80...
  • Page 21 SAVE button. You can see the live video when you click the live view button as below. When you exit Speco-NVR, you have to input the ID/PW, admin/1234. Details for the Speco-NVR can be found in [Speco-NVR User’s Guide].
  • Page 22 ONSIP OS101 User’s Guide 4. Additional settings through connection to the Admin Page All the parameters of new Video server follows factory default values. For more sophisticated target application it is needed to change parameters. The admin page can be connected through ”http://IP_address:HTTP_port_number”/admin.htm...

  • Page 23: Trouble Shooting

    If PoE is not applied, the power and network connection should be made through separate cables. It is recommended to use DC adaptor supplied by Speco Technology for the feeding of the power. In case of replacing the DC power supply, make sure that the power supply meets with the power requirement of the IP camera to prevent damage or malfunction.

  • Page 24: Cannot Connect To The Video

    ONSIP OS101 User’s Guide 4.2. Cannot connect to the Video Check the status of the network connection through PING test. Try the following on your PC: Start > Run > Cmd > Ping IP address (Ex : Ping 172.16.42.51) If “Reply from ~” message is returned ( in the figure below), the network connection is in normal state.

  • Page 25: Windows Vista Or Windows 7

    4.3. Windows Vista or Windows 7 Windows Vista and Windows 7 users need to configure UAC (User Access Control) and Privilege Level for proper recording and still video capture in Speco-NVR and Web Viewer. <Windows Vista> 1. UAC (User Access Control) configuration 1) Double-click “User Accounts”...
  • Page 26 ONSIP OS101 User’s Guide <Windows 7> 1. UAC (User Access Control) configuration 1) Double-click “User Accounts” in control panel 2) Double-click “Change User Account Control setting” 3) Set to “Never notify” Rev.1.0 (Nov., 2011)
  • Page 27 ONSIP OS101 User’s Guide 2. Privilege Level Control 1) Select “NVR” icon on the desktop 2) Click right mouse button and select “properties” 3) Check “Privilege Level” in “Compatibility” tab Rev.1.0 (Nov., 2011)

  • Page 28: Technical Assistance

    ONSIP OS101 User’s Guide 4.4. Technical Assistance If you need any technical assistance, please contact your dealer. For immediate service please provide the following information. 1. Model name 2. MAC address and Registration number 3. Purchase date 4. Description of the problem 5.

Table of Contents