Page 1 2011 Chevrolet HHR Owner Manual In Brief ..........1-1 Mirrors .
Page 2 2011 Chevrolet HHR Owner Manual Bulb Replacement ......6-41 Customer Assistance Information ....8-1 Windshield Wiper Blade Replacement .
Page 3: Canadian Owners
P.O. Box 07130 manual including, but not limited to, GM, the GM logo, Detroit, MI 48207 CHEVROLET, the CHEVROLET Emblem, and HHR are 1-800-551-4123 trademarks and/or service marks of General Motors LLC, its subsidiaries, affiliates, or licensors.
Page 4: Vehicle Symbols
Safety Warnings and Symbols A circle with a slash through it is a safety Warning messages found on vehicle labels and in this symbol which means Do manual describe hazards and what to do to avoid or Not, Do not do this, or reduce them.
Page 5: Vehicle Symbol Chart
Vehicle Symbol Chart : Fuel Gauge Here are some additional symbols that may be found on : Fuses the vehicle and what they mean. For more information : Headlamp High/Low-Beam Changer on the symbol, refer to the Index. : LATCH System Child Restraints : Airbag Readiness Light : Malfunction Indicator Lamp : Air Conditioning...
Page 6 NOTES...
Page 7: In Brief
Section 1 In Brief Instrument Panel ........1-2 Portable Audio Devices (Auxiliary Input or USB Port) .
Page 8: Instrument Panel
Instrument Panel...
Page 9 A. Outlet Adjustment on page 4 20. M. Horn on page 4 3. B. Cruise Control on page 4 8 (If Equipped). N. Audio Steering Wheel Controls on page 4 79 (If Equipped). C. Turn Signal/Multifunction Lever on page 4 4. O.
Page 10: Initial Drive Information
Initial Drive Information Press to lock all doors. This section provides a brief overview about some of Lock and unlock feedback can be personalized. the important features that may or may not be on your Press and hold for approximately specific vehicle.
Page 11: Canceling A Remote Start
When the vehicle starts, the parking lamps will turn on The power door lock and remain on as long as the engine is running. The switches are on the doors will be locked and the climate control system may front doors. come on.
Page 12: Seat Adjustment
Windows Seat Adjustment Manual Seats 1. Lift the bar under the seat to unlock the seat. 2. Slide the seat to the desired position and release the bar. On vehicles with power windows, the switches are on each of the side doors. The driver door also has switches that control the passenger and rear windows.
Page 13 Power Seats Reclining Seatbacks 1. Lift the lever to release the seatback. Move the seat forward or rearward by moving the control forward or rearward. 2. Move the seatback to where you want it and release the lever. Raise or lower the front of the seat, or the entire seat, by moving the front or rear of the control up or down.
Page 14: Second Row Seats
Second Row Seats Power Lumbar Press the front or rear of the control to increase or decrease lumbar support. The seatbacks can be folded flat. See Power Lumbar on page 2 6. For detailed instructions for lowering the seatback(s), see Split Folding Rear Seat on page 2 12.
Page 15: Heated Seats
Heated Seats For more information see Head Restraints on page 2 2 and Manual Seats on page 2 4. Safety Belt On vehicles with this feature, the controls are located on the climate control panel. Press the button to turn the heated seat on to the high setting, a second time to go to the low setting, and a third to turn it off.
Page 16: Sensing System For Passenger Airbag
Sensing System for Passenger Mirror Adjustment Airbag Exterior Mirrors The passenger sensing system, if equipped, will turn off Controls for the outside the right front passenger frontal airbag under certain power mirrors are located conditions. The driver airbags and roof rail airbags are on the driver door not affected by this.
Page 17: Interior Mirror
Interior Mirror Steering Wheel Adjustment Vehicles with a manual rearview mirror can be adjusted by holding the mirror in the center to move it for a clearer view behind the vehicle. To avoid glare from the headlamps behind you, push the tab, located at the base of the mirror, toward you for daytime use and pull it for nighttime use.
Page 18: Interior Lighting
Interior Lighting Exterior Lighting Dome Lamps The front and rear dome lamps turn on when any door is opened. To turn on all dome lamps with the doors closed, turn the instrument panel brightness thumbwheel located to the right of the steering wheel and above the radio, completely to the right.
Page 19: Windshield Wiper/Washer
For more information, see: : When the lever is in the delay position, turn the band up for more frequent wipes or down for less frequent Headlamps on page 4 11. wipes. Fog Lamps on page 4 13. During intermittent wiping mode, the delay cycle time is Daytime Running Lamps (DRL) on page 4 12.
Page 20 Rear Window Wiper/Washer Climate Controls The heating, cooling, and ventilation for the vehicle can be controlled with this system. The rear window wiper/washer button is located on the instrument panel below the climate controls. : Press to turn on the intermittent wiping setting that has a longer delay.
Page 21: Vehicle Features
Vehicle Features : For vehicles with XM, MP3, WMA, or RDS features, press to display additional text information related to the current FM-RDS or XM station; or CD, MP3, Radio(s) WMA song. Song title information will be displayed on the top line of the display while the artist information will be displayed on the bottom line, if the information is available during XM, CD, MP3, or WMA playback.
Page 22: Setting The Clock
Setting the Clock A fee is required to receive the XM service. For more information, refer to: To set the time and date for the Radio with CD (MP3) and USB port or Radio with a Single CD (MP3) player: www.xmradio.com or call 1-800-929-2100 (U.S.) 1.
Page 23: Steering Wheel Controls
® Steering Wheel Controls Bluetooth For vehicles with an in-vehicle Bluetooth system, it If equipped, some audio allows users with a Bluetooth enabled cell phone to controls can be adjusted make and receive hands-free calls using the vehicle s using the controls on the audio system and controls.
Page 24: Vehicle Personalization
Door Lock and Unlock Settings The DIC buttons are located on the left side of Language the steering wheel. See DIC Vehicle Personalization on page 4 45. Cruise Control The cruise control buttons are located on the left side of the steering wheel. INFO: Press to scroll through the vehicle information displays.
Page 25: Storage Compartments
Storage Compartments Vehicles with a panel/cargo cover feature can be adjusted into four positions. Place the panel in the upper position to conceal the cargo area. There is also a center position and a sideways position that allows access to the rear cargo area. Place the panel lower position for additional cargo For more information, see Rear Compartment Storage space above it.
Page 26: Performance And Maintenance
Power Outlets For more information, see Traction Control System (TCS) on page 5 8. Accessory power outlets can be used to connect electrical equipment, such as a cell phone or Electronic Stability Control (ESC) MP3 player. The Electronic Stability Control system assists with There are two accessory power outlets located on the directional control of the vehicle in difficult driving instrument panel below the climate controls and at the...
Page 27 Tire Pressure Monitor Tire Sealant and Compressor Kit This vehicle may have a Tire Pressure Monitor This vehicle may come with a jack and spare tire or a System (TPMS). tire sealant and compressor kit. The kit can be used to seal small punctures in the tread area of the tire.
Page 28: Driving For Better Fuel Economy
4. Press and hold the reset button until the DIC Driving for Better Fuel Economy display shows ACKNOWLEDGED. This will tell you Driving habits can affect fuel mileage. Here are some the system has been reset. driving tips to get the best fuel economy possible. 5.
Page 29 U.S.: 1-800-CHEV-USA (1-800-243-8872) TTY Users: 1-888-889-2438 Canada: 1-800-268-6800 As the owner of a new Chevrolet, you are automatically enrolled in the Roadside Assistance program. This program provides technically trained advisors who are available 24 hours a day, 365 days a year, minor repair information or towing arrangements.
Page 30: How Onstar Service Works
How OnStar Service Works OnStar service requires wireless communication networks and the Global Positioning System (GPS) : Push this blue button to connect to a specially satellite network. Not all OnStar services are available trained OnStar advisor to verify your account everywhere or on all vehicles at all times.
Page 31: Your Responsibility
See Radio Frequency Statement on page 8 17 for Your Responsibility information regarding Part 15 of the Federal Increase the volume of the radio if the OnStar advisor Communications Commission (FCC) rules and Industry cannot be heard. Canada Standards RSS-210/220/310. If the light next to the OnStar buttons is red, the system OnStar Steering Wheel Controls may not be functioning properly.
Page 32 NOTES 1-26...
Page 33: Seats And Restraint System
Section 2 Seats and Restraint System Head Restraints ........2-2 Where to Put the Restraint .
Page 34: Head Restraints
Head Restraints The front seats have adjustable head restraints in the outboard seating positions. WARNING: With head restraints that are not installed and adjusted properly, there is a greater chance that occupants will suffer a neck/spinal injury in a crash. Do not drive until the head restraints for all occupants are installed and adjusted properly.
Page 35 Pull the head restraint up to raise it. To lower the head restraint, press the button, located on the top of the seatback, and push the restraint down. Push down on the head restraint after the button is released to make sure that it is locked in place. The head restraints are not designed to be removed.
Page 36: Front Seats
Front Seats 1. Lift the bar to unlock the seat. 2. Slide the seat to the Manual Seats desired position and release the bar. WARNING: You can lose control of the vehicle if you try to adjust a manual driver seat while the vehicle is moving.
Page 37: Power Seat
Seat Height Adjuster Power Seat Driver Seat Shown If your vehicle has this feature, the driver's seat height If the vehicle has a power seat, the control used to adjuster is located on the outboard side of the seat. operate it is on the outboard side of the driver seat. To raise the seat, move the lever upward repeatedly To adjust the seat: until the seat is at the desired height.
Page 38: Power Lumbar
Power Lumbar If your vehicle has this feature, the control is located on the outboard side of the driver's seat cushion. To increase support, press and hold the front of the control. To decrease support, press and hold the rear of the control.
Page 39 Heated Seats If your vehicle has this feature, the driver and passenger heated seat WARNING: buttons are on the climate control panel below the fan switch. If you cannot feel temperature change or pain to the skin, the seat heater may cause burns even at low temperatures.
Page 40: Reclining Seatbacks
Reclining Seatbacks WARNING: You can lose control of the vehicle if you try to adjust the seat while the vehicle is moving. The sudden movement could startle and confuse you, or make you push a pedal when you do not want to.
Page 41 WARNING: Sitting in a reclined position when the vehicle is in motion can be dangerous. Even when buckled up, the safety belts cannot do their job when reclined like this. The shoulder belt cannot do its job because it will not be against your body.
Page 42: Passenger Folding Seatback
Passenger Folding Seatback WARNING: Your vehicle has a front passenger seat that folds flat. Things you put on this seatback can strike and WARNING: injure people in a sudden stop or turn, or in a crash. Remove or secure all items before driving. If you fold the seatback forward to carry longer objects, such as skis, be sure any such cargo is To fold the seatback, do the following:...
Page 43 To raise the seatback to an upright position: 1. Pull up on either lever. 2. Push the seatback up until it is in a locked position. WARNING: If either seatback is not locked, it could move forward in a sudden stop or crash. That could cause injury to the person sitting there.
Page 44: Rear Seats
Rear Seats Split Folding Rear Seat The seatbacks can be folded flat. To lower the rear seatback(s): 1. Move the front seat forward and/or put the front seatback in an upright position so it does not interfere with folding the rear seatback forward. 2.
Page 45 To raise the rear seatback(s): 5. Pull up on the knob located on the top of the seatback on the WARNING: outboard side to release the seatback. A safety belt that is improperly routed, not properly attached, or twisted will not provide the protection needed in a crash.
Page 46: Safety Belts
Safety Belts WARNING: Safety Belts: They Are for Everyone If the seatback is not locked, it could move This section of the manual describes how to use safety forward in a sudden stop or crash. That could belts properly. It also describes some things not to do cause injury to the person sitting there.
Page 47 In most states and in all Canadian provinces, the law WARNING: requires wearing safety belts. Here is why: You never know if you will be in a crash. If you do have a crash, you do not know if it will be a serious one. It is extremely dangerous to ride in a cargo area, A few crashes are mild, and some crashes can be so inside or outside of a vehicle.
Page 48: Why Safety Belts Work
Why Safety Belts Work When you ride in or on anything, you go as fast as it goes. Put someone on it. Take the simplest vehicle. Suppose it is just a seat on wheels. 2-16...
Page 49 Get it up to speed. Then stop the vehicle. The rider The person keeps going until stopped by something. does not stop. In a real vehicle, it could be the windshield... 2-17...
Page 50 or the instrument panel... or the safety belts! With safety belts, you slow down as the vehicle does. You get more time to stop. You stop over more distance, and your strongest bones take the forces. That is why safety belts make such good sense. 2-18...
Page 51: Questions And Answers About Safety Belts
Questions and Answers About Safety Q: If I am a good driver, and I never drive far from home, why should I wear safety belts? Belts A: You may be an excellent driver, but if you are in a crash even one that is not your fault you and Q: Will I be trapped in the vehicle after a crash if I...
Page 52 It is very important for all occupants to buckle up. Sit up straight and always keep your feet on the floor in Statistics show that unbelted people are hurt more often front of you. The lap part of the belt should be worn low in crashes than those who are wearing safety belts.
Page 53 Q: What is wrong with this? WARNING: You can be seriously hurt if your shoulder belt is too loose. In a crash, you would move forward too much, which could increase injury. The shoulder belt should fit snugly against your body. A: The shoulder belt is too loose.
Page 54 Q: What is wrong with this? WARNING: You can be seriously hurt if your lap belt is too loose. In a crash, you could slide under the lap belt and apply force on your abdomen. This could cause serious or even fatal injuries. The lap belt should be worn low and snug on the hips, just touching the thighs.
Page 55 Q: What is wrong with this? WARNING: You can be seriously injured if your belt is buckled in the wrong place like this. In a crash, the belt would go up over your abdomen. The belt forces would be there, not on the pelvic bones. This could cause serious internal injuries.
Page 56 Q: What is wrong with this? WARNING: You can be seriously injured if your belt goes over an armrest like this. The belt would be much too high. In a crash, you can slide under the belt. The belt force would then be applied on the abdomen, not on the pelvic bones, and that could cause serious or fatal injuries.
Page 57 Q: What is wrong with this? WARNING: You can be seriously injured if you wear the shoulder belt under your arm. In a crash, your body would move too far forward, which would increase the chance of head and neck injury. Also, the belt would apply too much force to the ribs, which are not as strong as shoulder bones.
Page 58 Q: What is wrong with this? WARNING: You can be seriously injured by not wearing the lap-shoulder belt properly. In a crash, you would not be restrained by the shoulder belt. Your body could move too far forward increasing the chance of head and neck injury.
Page 59 Q: What is wrong with this? WARNING: You can be seriously injured by a twisted belt. In a crash, you would not have the full width of the belt to spread impact forces. If a belt is twisted, make it straight so it can work properly, or ask your dealer to fix it.
Page 60: Lap-Shoulder Belt
Lap-Shoulder Belt All seating positions in the vehicle have a lap-shoulder belt. The following instructions explain how to wear a lap-shoulder belt properly. 1. Adjust the seat, if the seat is adjustable, so you can sit up straight. To see how, see Seats in the Index.
Page 61 To unlatch the belt, push the button on the buckle. The 5. To make the lap part tight, pull up on the belt should return to its stowed position. shoulder belt. Before a door is closed, be sure the safety belt is out of It may be necessary to pull stitching on the safety the way.
Page 62 Shoulder Belt Height Adjuster Safety Belt Pretensioners The vehicle has a shoulder belt height adjuster for the This vehicle has safety belt pretensioners for front driver and right front passenger seating positions. outboard occupants. Although the safety belt pretensioners cannot be seen, they are part of the Adjust the height so the shoulder portion of the belt is safety belt assembly.
Page 63: Rear Safety Belt Comfort Guides
Rear Safety Belt Comfort Guides This vehicle may have rear shoulder belt comfort guides for each outboard passenger position in the rear seat. If not, they are available through your dealer. The guides may provide added safety belt comfort for older children who have outgrown booster seats and for some adults.
Page 64 3. Be sure that the belt is not twisted and it lies flat. The elastic cord must be under the belt and the 4. Buckle, position, and release the safety belt as described previously in this section. Make sure the guide on top.
Page 65: Safety Belt Use During Pregnancy
Safety Belt Use During Pregnancy Safety Belt Extender Safety belts work for everyone, including pregnant If the vehicle's safety belt will fasten around you, you women. Like all occupants, they are more likely to be should use it. seriously injured if they do not wear safety belts. But if a safety belt is not long enough, your dealer will order you an extender.
Page 66: Child Restraints
Buckle the lap-shoulder belt. Does the shoulder Child Restraints belt rest on the shoulder? If yes, continue. If no, try using the rear safety belt comfort guide. See Rear Older Children Safety Belt Comfort Guides under Lap-Shoulder Belt on page 2 28 for more information. If the shoulder belt still does not rest on the shoulder, then return to the booster seat.
Page 67 Also see Rear Safety Belt Comfort Guides under Lap-Shoulder Belt on page 2 28. According to accident statistics, children and infants are safer when properly restrained in a child restraint system or infant restraint system secured in a rear seating position. In a crash, children who are not buckled up can strike other people who are buckled up, or can be thrown out of the vehicle.
Page 68: Infants And Young Children
WARNING: Never do this. Never allow a child to wear the safety belt with the shoulder belt behind their back. A child can be seriously injured by not wearing the lap-shoulder belt properly. In a crash, the child would not be restrained by the shoulder belt.
Page 69 WARNING: WARNING: (Continued) during a crash. For example, in a crash at only Children can be seriously injured or strangled if a 40 km/h (25 mph), a 5.5 kg (12 lb) infant will shoulder belt is wrapped around their neck and suddenly become a 110 kg (240 lb) force on a the safety belt continues to tighten.
Page 70 WARNING: Never do this. Children who are up against, or very close to, any airbag when it inflates can be seriously injured or killed. Never put a rear-facing child restraint in the right front seat. Secure a rear-facing child restraint in a rear seat.
Page 71 For most basic types of child restraints, there are many different models available. When purchasing a WARNING: child restraint, be sure it is designed to be used in a motor vehicle. If it is, the restraint will have a label A young child's hip bones are still so small that saying that it meets federal motor vehicle safety standards.
Page 72: Child Restraint Systems
Child Restraint Systems A rear-facing infant seat (A) provides restraint with the seating surface against the back of the infant. The harness system holds the infant in place and, in a crash, acts to keep the infant positioned in the restraint. A booster seat (C-D) is a child restraint designed to improve the fit of the vehicle's safety belt system.
Page 73: Securing The Child Within The Child Restraint
Securing an Add-On Child Restraint in Keep in mind that an unsecured child restraint can move around in a collision or sudden stop and injure the Vehicle people in the vehicle. Be sure to properly secure any child restraint in the vehicle even when no child is in it.
Page 74: Where To Put The Restraint
Where to Put the Restraint WARNING: (Continued) According to accident statistics, children and infants are safer when properly restrained in a child restraint system or infant restraint system secured in a rear injured or killed if the right front passenger airbag seating position.
Page 75: Lower Anchors And Tethers For Children (Latch)
If the vehicle does not have a rear seat that will Lower Anchors and Tethers for accommodate a rear-facing child restraint, a rear-facing Children (LATCH) child restraint should not be installed in the vehicle, even if the airbag is off. The LATCH system holds a child restraint during driving or in a crash.
Page 76: Top Tether Anchor
Lower Anchors Top Tether Anchor Lower anchors (A) are metal bars built into the vehicle. A top tether (A, C) anchors the top of the child restraint There are two lower anchors for each LATCH seating to the vehicle. A top tether anchor is built into the position that will accommodate a child restraint with vehicle.
Page 77 Some child restraints that have a top tether are (Top Tether Anchor): designed for use with or without the top tether being Seating position with a attached. Others require the top tether always to be top tether anchor. attached. In Canada, the law requires that forward-facing child restraints have a top tether, and that the tether be attached.
Page 78 To assist you in locating the top tether anchors, this symbol is located next to each top tether anchor. On vehicles equipped with rear seats, the top tether anchor symbols for the rear outboard positions are on the lower side of the quarter panels. The top tether Vehicles with Rear Seats anchor symbols for the rear center position are on the The rear outboard top tether anchors are located on the...
Page 79 When the top tether anchor is being used for a child If the vehicle is a panel van equipped with a cargo restraint, do not use the same anchor to secure cargo. partition, see the Cargo Partition Owner Manual Supplement for the top tether anchor location and routing instructions.
Page 80: Securing A Child Restraint Designed For The Latch System
Securing a Child Restraint Designed for the WARNING: (Continued) LATCH System break during a crash. A child or others could be WARNING: injured. To reduce the risk of serious or fatal injuries during a crash, attach only one child If a LATCH-type child restraint is not attached to restraint per anchor.
Page 81 Notice: Do not let the LATCH attachments rub 2. If the child restraint manufacturer recommends that against the vehicle s safety belts. This may damage the top tether be attached, attach and tighten the these parts. If necessary, move buckled safety belts top tether to the top tether anchor, if equipped.
Page 82 2. 3. To secure a child restraint in the front 2. 6. Route, attach, and tighten the top tether passenger position, only if your vehicle does according to your child restraint instructions not have rear seats, find the top tether and the following instructions: anchor located on the passenger side cargo If the position you are...
Page 83: Securing A Child Restraint In A Rear
to move it side to side and back and forth. There If the position you are should be no more than 2.5 cm (1 in) of movement, using has an adjustable for proper installation. headrest or head restraint and you are using a Securing a Child Restraint in a Rear single tether, raise the headrest or head restraint...
Page 84 If the child restraint does not have the LATCH system, you will be using the safety belt to secure the child restraint in this position. Be sure to follow the instructions that came with the child restraint. Secure the child in the child restraint when and as the instructions say.
Page 85 4. Pull the shoulder belt all the way out of the 5. To tighten the belt, push down on the child retractor to set the lock. When the retractor lock is restraint, pull the shoulder portion of the belt to set, the belt can be tightened but not pulled out of tighten the lap portion of the belt, and feed the the retractor.
Page 86: Securing A Child Restraint In The Right Front Seat Position
6. If the child restraint has a top tether, follow the Securing a Child Restraint in the child restraint manufacturer's instructions regarding Right Front Seat Position the use of the top tether. See Lower Anchors and Tethers for Children (LATCH) on page 2 43 for This vehicle has airbags.
Page 87 A label on the sun visor says, Never put a rear-facing child seat in the front. This is because the risk to the WARNING: (Continued) rear-facing child is so great, if the airbag deploys. Secure rear-facing child restraints in a rear seat, WARNING: even if the airbag is off.
Page 88 Do not secure a child seat in a position without a top tether anchor if a national or local law requires that the top tether be anchored, or if the instructions that come with the child restraint say that the top strap must be anchored.
Page 89 5. Pull the shoulder belt all the way out of the 6. To tighten the belt, push down on the child retractor to set the lock. When the retractor lock is restraint, pull the shoulder portion of the belt to set, the belt can be tightened but not pulled out of tighten the lap portion of the belt, and feed the the retractor.
Page 90: Airbag System
7. If the vehicle does not have a rear seat and your Airbag System child restraint has a top tether, follow the child restraint manufacturer's instructions regarding the The vehicle has the following airbags: use of the top tether. See Lower Anchors and A frontal airbag for the driver.
Page 91 Here are the most important things to know about the WARNING: airbag system: WARNING: Be sure that cargo is not near an airbag. In a crash, an inflating airbag might force that object toward a person. This could cause severe injury You can be severely injured or killed in a crash if or even death.
Page 92 WARNING: WARNING: (Continued) Airbags inflate with great force, faster than the protection for adults and older children, but not for blink of an eye. Anyone who is up against, or very young children and infants. Neither the vehicle's close to, any airbag when it inflates can be safety belt system nor its airbag system is seriously injured or killed.
Page 93: Where Are The Airbags
Where Are the Airbags? The right front passenger's airbag is in the instrument panel on the passenger's side. The driver's frontal airbag is in the middle of the steering wheel. 2-61...
Page 94 WARNING: If something is between an occupant and an airbag, the airbag might not inflate properly or it might force the object into that person causing severe injury or even death. The path of an inflating airbag must be kept clear. Do not put anything between an occupant and an airbag, and do not attach or put anything on the steering wheel hub or on or near any other airbag...
Page 95: When Should An Airbag Inflate
If the vehicle goes into an object at an angle, the When Should an Airbag Inflate? airbags could inflate at a different crash speed than if the vehicle goes straight into the object. Frontal airbags are designed to inflate in moderate to severe frontal or near-frontal crashes to help reduce the Thresholds can also vary with specific vehicle design.
Page 96: How Does An Airbag Restrain
In any particular crash, no one can say whether an How Does an Airbag Restrain? airbag should have inflated simply because of the In moderate to severe frontal or near frontal collisions, damage to a vehicle or because of what the repair costs even belted occupants can contact the steering wheel were.
Page 97: What Will You See After An Airbag
What Will You See After an Airbag WARNING: Inflates? After the frontal airbags inflate, they quickly deflate, so When an airbag inflates, there may be dust in the quickly that some people may not even realize an air. This dust could cause breathing problems for airbag inflated.
Page 98: Passenger Sensing System
The vehicle has a crash sensing and diagnostic module which records information after a crash. WARNING: See Vehicle Data Recording and Privacy on page 8 15 and Event Data Recorders on page 8 16. A crash severe enough to inflate the airbags may have also damaged important functions in the Let only qualified technicians work on the airbag vehicle, such as the fuel system, brake and...
Page 99 The passenger sensing system will turn off the right front passenger frontal airbag under certain conditions. The driver airbag and roof rail airbags are not affected by the passenger sensing system. The passenger sensing system works with sensors that are part of the right front passenger seat. The sensors are designed to detect the presence of a properly-seated occupant and determine if the right United States...
Page 100 A label on the sun visor says, Never put a rear-facing child seat in the front. This is because the risk to the WARNING: (Continued) rear-facing child is so great, if the airbag deploys. always move the front passenger seat as far back WARNING: as it will go.
Page 101 The passenger sensing system is designed turn on If the On Indicator is Lit for a Child (may inflate) the right front passenger frontal airbag Restraint anytime the system senses that a person of adult size is sitting properly in the right front passenger seat. When If a child restraint has been installed and the on the passenger sensing system has allowed the airbag indicator is lit:...
Page 102 The passenger sensing system may or may not If a person of adult-size is sitting in the right front turn off the airbag for a child in a child restraint passenger seat, but the off indicator is lit, it could be depending upon the child's seating posture and because that person is not sitting properly in the seat.
Page 103 Liquid pooled on the seat that has not soaked in Additional Factors Affecting System may make it more likely that the passenger Operation sensing system will enable (turn on) the passenger airbag while a child restraint or child occupant is on Safety belts help keep the passenger in position on the the seat.
Page 104: Servicing Your Airbag-Equipped Vehicle
Servicing Your Airbag-Equipped Adding Equipment to Your Vehicle Airbag-Equipped Vehicle Airbags affect how the vehicle should be serviced. Q: Is there anything I might add to or change about There are parts of the airbag system in several places the vehicle that could keep the airbags from around the vehicle.
Page 105: Restraint System Check
installed under or on top of the seat fabric, could Restraint System Check also interfere with the operation of the passenger sensing system. This could either prevent proper Checking the Restraint Systems deployment of the passenger airbag(s) or prevent the passenger sensing system from properly turning Safety Belts off the passenger airbag(s).
Page 106: Replacing Restraint System Parts
Airbags If the vehicle has been in a crash, do you need new safety belts or LATCH system (if equipped) parts? The airbag system does not need regularly scheduled maintenance or replacement. Make sure the airbag After a very minor crash, nothing may be necessary. But readiness light is working.
Page 107: Table Of Contents
Section 3 Features and Controls Keys ..........3-3 Theft-Deterrent Systems .
Page 108 Section 3 Features and Controls Mirrors ..........3-36 Instrument Panel Storage .
Page 109: Keys
Keys WARNING: Leaving children in a vehicle with the ignition key is dangerous for many reasons. Children or others could be badly injured or even killed. They could operate the power windows or other controls or even make the vehicle move. The windows will function with the keys in the ignition and children could be seriously injured or killed if caught in the path of a closing window.
Page 110: Remote Keyless Entry (Rke) System
Notice: If the keys get locked in the vehicle, it may Remote Keyless Entry (RKE) System have to be damaged to get them out. Always carry a Operation spare key. The Remote Keyless Entry (RKE) transmitter functions If you are locked out of your vehicle, contact Roadside work up to 60 feet (18 m) away from the vehicle.
Page 111: Programming Transmitters To The Vehicle
(Lock): Press to lock all the doors. The interior (Vehicle Locator/Panic Alarm): Press and release lamps turn off after all of the doors are closed. to activate the vehicle locate feature. The horn chirps If enabled through the Driver Information Center (DIC), three times and the headlamps and parking lamps flash the parking lamps flash once to indicate locking has three times.
Page 112: Remote Vehicle Start
Battery Replacement 3. Insert the new battery, positive side facing up. Replace with a CR2032 or equivalent battery. Replace the battery if the KEY FOB BATT LOW 4. Snap the transmitter back together. message displays in the DIC. See KEY FOB BATT LOW under DIC Warnings and Messages on Remote Vehicle Start page 4 40 for additional information.
Page 113 To start the engine using the remote start feature: After your vehicle's engine has been started two times using the remote start button, the vehicle's ignition 1. Aim the RKE transmitter at the vehicle. switch must be turned to ON/RUN and then back to 2.
Page 114: Doors And Locks
Doors and Locks WARNING: (Continued) Door Locks Outsiders can easily enter through an unlocked door when you slow down or stop WARNING: your vehicle. Locking your doors can help prevent this from happening. Unlocked doors can be dangerous. There are several ways to lock and unlock your vehicle. Passengers, especially children, can easily open the doors and fall out of a moving To lock the driver's door from the outside, turn the key...
Page 115: Power Door Locks
Power Door Locks Delayed Locking This feature will delay the actual locking of the doors The power door lock and liftgate when the power door lock switch or remote switches are located on keyless entry transmitter is used to lock the vehicle. the driver's and front passenger's door next to If any door is open when locking the vehicle, three...
Page 116: Automatic Door Lock
Automatic Door Lock Rear Door Security Locks On vehicles with power door locks, the doors Vehicles with rear door security locks prevent automatically lock when the shift lever is moved out passengers from opening the rear doors from the of (P) Park for a vehicle with an automatic transmission. inside.
Page 117: Lockout Protection
To open a rear door while the security lock is on, do the Rear Side Cargo Door following: The rear side cargo doors can be opened by pressing 1. Unlock the door using the remote keyless entry the buttons located on the driver and passenger sides transmitter, the power door lock switch, or by lifting of the instrument panel, or by using the Remote Keyless the rear door manual lock.
Page 118 Open the liftgate by pressing the touchpad located in the handle above the license plate. Once slightly WARNING: (Continued) opened, the liftgate will rise by itself. Lamps in the rear of the vehicle will come on, illuminating the rear cargo If the vehicle must be driven with the liftgate, area, unless the dome lamp lever is in the off position.
Page 119 Manual Liftgate Release 2. Locate the release lever on the latch. To manually open the liftgate, do the following: The lever is located about three inches (7.62 cm) behind the trim in the access hole. 1. Remove the trim plug, located on the inside of the liftgate near the center.
Page 120 Push the release lever rearward. 4. The liftgate will unlatch when the lever is pushed rearward. Push the liftgate to open. 3. Insert a tool into the access hole. 5. Reinstall the trim plug. 3-14...
Page 121: Windows
Windows WARNING: Leaving children, helpless adults, or pets in a vehicle with the windows closed is dangerous. They can be overcome by the extreme heat and suffer permanent injuries or even death from heat stroke. Never leave a child, a helpless adult, or a pet alone in a vehicle, especially with the windows closed in warm or hot weather.
Page 122: Power Windows
Power Windows WARNING: Leaving children in a vehicle with the keys is dangerous for many reasons. Children or others could be badly injured or even killed. They could operate the power windows or other controls or even make the vehicle move. The windows will function and they could be seriously injured or Driver's Side Shown killed if caught in the path of a closing window.
Page 123: Sun Visors
Express-Down Window Visor Vanity Mirrors Your vehicle has visor vanity mirrors. Swing down the The driver's window switch has an express-down sun visor and lift the cover to expose the mirror. feature that allows the window to be lowered without holding the switch.
Page 124: Disarming The System
The system will arm after either of the following occur: How the System Alarm is Activated 30 seconds after all the doors are closed. If the system is armed, it can be activated by either: 60 seconds with any door open. Opening the driver's door or tailgate.
Page 125: Pass-Key Iii+ Electronic Immobilizer
® PASS-Key III+ Electronic When trying to start the vehicle if the engine does not start and the security light comes on, there may be a Immobilizer problem with your theft-deterrent system. Turn the ignition off and try again. See Radio Frequency Statement on page 8 17 for information regarding Part 15 of the Federal If the engine still does not start, and the key appears to Communications Commission (FCC) rules and Industry...
Page 126: Starting And Operating Your Vehicle
To program the new key: Starting and Operating Your 1. Verify that the new key has a stamped on it. Vehicle 2. Insert the already programmed key in the ignition New Vehicle Break-In and start the engine. If the engine will not start, see your dealer for service.
Page 127: Ignition Positions
Ignition Positions 9(STOPPING THE ENGINE/LOCK/OFF): When the vehicle is stopped, turn the ignition switch to LOCK/OFF to turn the engine off. Retained Accessory Power (RAP) will remain active. See Retained Accessory Power (RAP) on page 3 24. This position locks the steering column when the key is removed.
Page 128 3. Come to a complete stop, shift to P (Park), and ACC (ACC/ACCESSORY): This position operates turn the ignition to LOCK/OFF. On vehicles with an some of the electrical accessories. It unlocks the automatic transmission, the shift lever must be in steering wheel and ignition.
Page 129 Column Lock Release For vehicles with an automatic transmission, the following procedure allows the ignition to be turned to LOCK/OFF and ignition key to be removed in case of a dead battery or low voltage battery. 1. Make sure the shift lever is in P (Park). 3.
Page 130: Manual Transmission
Retained Accessory Power (RAP) Manual Transmission The shift lever should be in N (Neutral) and the parking These vehicle accessories may be used for up to brake engaged. Hold the clutch pedal down to the floor 10 minutes after the engine is turned off. and start the engine.
Page 131: Engine Coolant Heater
Notice: Cranking the engine for long periods of Notice: The engine is designed to work with the time, by returning the key to the START position electronics in the vehicle. If you add electrical parts immediately after cranking has ended, can overheat or accessories, you could change the way the and damage the cranking motor, and drain the engine operates.
Page 132: Automatic Transmission Operation
To Use the Engine Coolant Heater Automatic Transmission Operation 1. Turn off the engine. If the vehicle has an automatic transmission, the shift lever is located on the console between the seats. 2. Open the hood and unwrap the electrical cord. The electrical cord is located on the passenger side of There are several the vehicle near the headlamp and the radiator.
Page 133 R (Reverse): Use this gear to back up. WARNING: (Continued) Notice: Shifting to R (Reverse) while the vehicle is moving forward could damage the transmission. The repairs would not be covered by the vehicle Do not leave the vehicle when the engine is warranty.
Page 134 Notice: Shifting out of P (Park) or N (Neutral) with PERFORMANCE SHIFTING: If the vehicle has this the engine running at high speed may damage the feature, it can detect a change in driving patterns while transmission. The repairs would not be covered by in the Intermediate position.
Page 135: Manual Transmission Operation
Manual Transmission Operation shift lever in N (Neutral) and let up on the clutch pedal. Press the clutch pedal back down. Then shift into 1 (First). 2 (Second): Press the clutch pedal as you let up on the accelerator pedal and shift into 2 (Second). Then, slowly let up on the clutch pedal as you press the accelerator pedal.
Page 136: Shift Speeds
Shift Speeds Parking Brake WARNING: If you skip a gear when you downshift, you could lose control of the vehicle. You could injure yourself or others. Do not shift down more than one gear at a time when you downshift. Up-Shift Light If the vehicle has a manual transmission,...
Page 137: Shifting Into Park (Automatic Transmission)
If parking on a hill and pulling a trailer, see Towing a WARNING: (Continued) Trailer (Automatic Transmission) on page 5 31 or Towing a Trailer (Manual Transmission) on page 5 37. Shifting Into Park (Automatic or others could be injured. Move your hand lower on the lever or raise the seat back so that you can Transmission) set the brake.
Page 138 2. Move the shift lever into P (Park) by holding in the Torque Lock (Automatic Transmission) button on the shift lever and pushing the lever all If you are parking on a hill and you do not shift into the way toward the front of the vehicle. P (Park) properly, the weight of the vehicle may put too 3.
Page 139: Shifting Out Of Park
Shifting Out of Park (Automatic If you still are unable to shift out of P (Park): 1. Fully release the shift lever button. Transmission) 2. While holding down the brake pedal, press the shift This vehicle is equipped with an electronic shift lock lever button again.
Page 140: Parking Over Things That Burn
Parking Over Things That Burn WARNING: (Continued) WARNING: The exhaust system leaks due to corrosion or damage. Things that can burn could touch hot exhaust The vehicle s exhaust system has been parts under the vehicle and ignite. Do not park modified, damaged or improperly repaired.
Page 141: Running The Vehicle While Parked
Running the Vehicle While Parked WARNING: It is better not to park with the engine running. But if you ever have to, here are some things to know. It can be dangerous to get out of the vehicle if the automatic transmission shift lever is not fully in WARNING: P (Park) with the parking brake firmly set.
Page 142: Mirrors
Mirrors Automatic Dimming Mirror Operation Automatic dimming reduces the glare of lights from Manual Rearview Mirror behind the vehicle. The dimming feature comes on and the indicator light illuminates each time the vehicle is Hold the inside rearview mirror in the center to move it started.
Page 143: Compass Variance
To calibrate the compass: 1. Make sure CAL is displayed. If CAL is not displayed, press and hold the compass button until CAL displays. 2. While CAL displays, drive the vehicle in circles at 5 mph (8 km/h) or less until the display reads a direction.
Page 144: Outside Power Mirrors
Outside Power Mirrors Keep the selector switch in the center position when not adjusting either outside mirror. Controls for the outside Manually fold the mirrors inward to prevent damage power mirrors are located when going through an automatic car wash. To fold, on the driver door push the mirror toward the vehicle.
Page 145: Object Detection Systems
Object Detection Systems WARNING: (Continued) Rear Vision Camera (RVC) or death. Even though the vehicle has the RVC The vehicle may have a Rear Vision Camera system. system, always check carefully before backing up Read this entire section before using it. by checking behind and around the vehicle.
Page 146 Rear Vision Camera Location The camera is located in the rear of the vehicle. The area displayed by the camera is limited and does not display objects that are close to either corner or under the bumper. The area displayed can vary depending on vehicle orientation or road conditions.
Page 147 The rear vision camera system display in the rearview A. View displayed by the camera. mirror may turn off or not appear as expected due to B. Corner of the rear bumper. one of the following conditions. If this occurs the left indicator light on the mirror will flash.
Page 148: Storage Areas
Storage Areas Floor Mats Glove Box WARNING: Lift up on the glove box lever to open it. If a floor mat is the wrong size or is not properly Cupholders installed, it can interfere with the accelerator pedal and/or brake pedal. Interference with the pedals There are two cupholders located in the floor console can cause unintended acceleration and/or between the front seats.
Page 149: Rear Storage Area
The driver side floor mat is held in place by a 3. Make sure the floor mat is properly secured and button-type retainer. verify that it does not interfere with the accelerator or brake pedals. Rear Storage Area Removing and Replacing the Floor Mat The vehicle could also have two rear storage areas that can be used for small items.
Page 150: Rear Compartment Storage Panel/Cover
Rear Compartment Storage Panel/ To use the panel in the lowest position: Cover The panel can be used in this position if additional space above the panel is needed. Cargo can be placed The vehicle could have an adjustable panel/cargo cover on top of the panel in this position.
Page 151 The center position is with the front corners placed in the lower guides and the rear corners placed in the upper guides. Do not load cargo on the panel in this position. The last position is with the front corners in the lower guides, panel sideways, closest to the rear seat for subfloor access.
Page 152: Roof Rack System
Roof Rack System Notice: Loading cargo directly on the roof of the vehicle may cause damage to the vehicle and would The vehicle may have a roof rack system. not be covered under warranty. Do not place cargo on the roof the vehicle. WARNING: To prevent damage or loss of cargo when driving, check to make sure crossrails and cargo are securely...
Page 153: Hideaway Rear Storage Bins
Hideaway Rear Storage Bins There is a rod that hooks into place to prop open the lid. Push the rod towards the lid to unhook it and lower The vehicle may have two storage bins located in the the lid. rear of the vehicle.
Page 154: Sunroof
Sunroof Express Open: To express open the power sunroof, fully press the driver's side switch rearward once. To The vehicle may have a power sunroof. stop the sunroof glass in a desired position other than to the express-open position, press the switch again, in The switches that operate either direction, to stop the movement.
Page 155 Close: To close the power sunroof, operate the controls according to one of the following: From the open position, press and hold the driver's side sunroof switch forward. The sunshade must be closed manually. From the vent position, press and hold the passenger's side sunroof switch rearward.
Page 156 NOTES 3-50...
Page 157 Section 4 Instrument Panel Instrument Panel Overview ......4-3 Climate Controls ........4-18 Hazard Warning Flashers .
Page 158 Section 4 Instrument Panel Front Fog Lamp Light ......4-36 Using an MP3 ....... . . 4-63 Highbeam On Light .
Page 159: Instrument Panel Overview
Instrument Panel Overview Tilt Wheel Hazard Warning Flashers (Hazard Warning Flasher): Press this button located on the instrument panel, to make the front and rear turn signal lamps flash on and off. This warns others that you are having trouble. Press again to turn the flashers off.
Page 160: Turn Signal/Multifunction Lever
Turn Signal/Multifunction Lever Turn and Lane-Change Signals An arrow on the instrument panel cluster flashes in the direction of the turn or lane change. Move the lever all the way up or down to signal a turn. Raise or lower the lever until the arrow starts to flash to signal a lane change.
Page 161: Headlamp High/Low-Beam Changer
Headlamp High/Low-Beam Changer Windshield Wipers To change the headlamps from low beam to high beam, push the turn signal lever away from you. This indicator light appears on the instrument panel cluster when the high beams are on. To change the headlamps from high beam to low beam, The windshield wiper lever is on the right side of the pull the turn signal lever toward you.
Page 162: Windshield Washer
9 (Off): Turns the windshield wipers off. Windshield Washer 8 (Mist): Single wipe, move the lever to and then To wash the windshield, press the button at the end of the lever until the washers begin. release it. Several wipes, hold lever on longer.
Page 163: Rear Window Wiper/Washer
Rear Window Wiper/Washer (Delay): Press to turn on the intermittent wiping setting that has a longer delay. The rear window washer/ (Washer Fluid): Press to wash and wipe the wiper button is located on window. the instrument panel below the climate The rear window washer uses the same fluid reservoir controls.
Page 164: Cruise Control
Cruise Control The cruise control buttons are located on the left With cruise control, a speed of about 40 km (25 mph) or side of the steering wheel. more can be maintained without keeping your foot on the accelerator. Cruise control does not work at speeds below 40 km (25 mph).
Page 165: Setting Cruise Control
Setting Cruise Control Resuming a Set Speed If the cruise button is on when not in use, it could get If the cruise control is set at a desired speed and then bumped and go into cruise when not desired. Keep the the brakes are applied, the cruise control is disengaged cruise control switch off when cruise is not being used.
Page 166 Reducing Speed While Using Cruise Using Cruise Control on Hills Control How well the cruise control works on hills depends upon the vehicle speed, load and the steepness of the hills. If the cruise control system is already activated, When going up steep hills, the accelerator pedal might Press and hold the SET button on the steering need to be applied to maintain the vehicle speed.
Page 167: Headlamps
Headlamps AUTO (Automatic Headlamp System): Automatically turns on the Daytime Running Lamps during daytime, and the headlamps, parking lamps, and taillamps at night. P (Off/On): This position is the momentary Off/On switch for the Automatic Headlamp System. In Canada, this only works when the vehicles with an automatic transmission are in P (Park) and vehicles with a manual transmission have the parking brake set and the vehicle is not moving.
Page 168: Wiper Activated Headlamps
Wiper Activated Headlamps The vehicle has a light sensor on top of the instrument panel. Do not cover this sensor or the headlamps will The headlamps and parking lamps are activated come on when they are not needed. 15 seconds after the windshield wipers are turned on. The DRL system will make the headlamps come on at For this feature to work, automatic lighting must be reduced brightness when the following conditions...
Page 169: Automatic Headlamp System
Automatic Headlamp System instrument panel brightness control is in the full bright position. See Instrument Panel Brightness on When it is dark enough outside, the automatic system page 4 14. turns on the headlamps at the normal brightness along To idle the vehicle with the system off, turn the ignition with other lamps such as the taillamps, sidemarker, on and turn the exterior light switch to the off/on parking lamps, instrument panel lights, and interior...
Page 170: Instrument Panel Brightness
Instrument Panel Brightness Entry/Exit Lighting The lamps inside the vehicle turn on when any door is The control for this feature opened. These lamps will fade out after about is located to the right of 20 seconds after all of the doors have been closed or the steering wheel and when the ignition is turned to ON/RUN.
Page 171: Electric Power Management
Electric Power Management engine idle speed to generate more power, whenever needed. It can temporarily reduce the power demands This vehicle has Electric Power Management (EPM), an of some accessories. advanced control system. It estimates the battery's Normally, these actions occur in steps or levels, without temperature and state of charge and then adjusts the being noticeable.
Page 172 Rear Power Plug for Converters WARNING: Power is always supplied to the outlets. Do not leave electrical equipment plugged in when the vehicle is not in use because the vehicle could catch fire and cause injury or death. Notice: Leaving electrical equipment plugged in for an extended period of time while the vehicle is off will drain the battery.
Page 173: Ashtray(S) And Cigarette Lighter
This plug can be used to supply power to commercial Notice: Hanging heavy equipment from the power converters and contains four different circuits. The outlet can cause damage not covered by the vehicle functions of these circuits are as follows; a 40 Amp warranty.
Page 174: Climate Controls
Climate Controls (Off): Turn the fan control to this position to turn the fan off. Climate Control System Temperature Control: Turn clockwise or counterclockwise to increase or decrease the The heating, cooling, and ventilation for the vehicle can temperature. be controlled with this system. (Fan): Turn clockwise or counterclockwise to For vehicles with remote start, the climate control increase or decrease the fan speed.
Page 175 The air conditioning system removes moisture from the (Defrost): This mode removes fog or frost from the air, so a small amount of water might drip under the windshield more quickly. Air is directed to the vehicle while idling or after turning off the engine. This windshield, with some air directed to the side window is normal.
Page 176: Rear Window Defogger
Rear Window Defogger Notice: Do not use anything sharp on the inside of the rear window. If you do, you could cut or damage The rear window defogger uses a warming grid to the warming grid, and the repairs would not be remove fog from the rear window.
Page 177: Passenger Compartment Air Filter
Passenger Compartment Air Filter The filter removes dust and pollen from the air which is drawn into the vehicle. Airflow reduction is an indication that the filter needs to be replaced. The filter should be replaced as part of routine scheduled maintenance.
Page 178: Warning Lights, Gauges, And Indicators
Warning Lights, Gauges, and Indicators Warning lights and gauges can signal that something is wrong before it becomes serious enough to cause an expensive repair or replacement. Paying attention to the warning lights and gauges could prevent injury. Warning lights come on when there might be or there is a problem with one of the vehicle's functions.
Page 179: Instrument Panel Cluster
Instrument Panel Cluster English Manual Transmission Shown, Automatic, and Metric similar 4-23...
Page 180: Speedometer And Odometer
Speedometer and Odometer Tachometer The speedometer shows the speed in both kilometers The tachometer displays per hour (km/h) and miles per hour (mph). the engine speed in revolutions per The vehicle's odometer works together with the Driver minute (rpm). Information Center (DIC). Trip A and Trip B can be set on the odometer.
Page 181: Safety Belt Reminders
Safety Belt Reminders Passenger Safety Belt Reminder Light For vehicles equipped with the passenger safety belt Driver Safety Belt Reminder Light reminder light, several seconds after the engine is When the engine is started, a chime sounds for several started, a chime sounds for several seconds to remind seconds to remind a driver to fasten the safety belt, the front passenger to buckle their safety belt.
Page 182: Airbag Readiness Light
Airbag Readiness Light WARNING: The system checks the airbag's electrical system for possible malfunctions. If the light stays on it indicates there is an electrical problem. The system check If the airbag readiness light stays on after the includes the airbag sensor, the pretensioners, the vehicle is started or comes on while driving, it airbag modules, the wiring and the crash sensing and means the airbag system might not be working...
Page 183: Passenger Airbag Status Indicator
Passenger Airbag Status Indicator Then, after several more seconds, the status indicator will light either ON or OFF, or either the on or off symbol If the vehicle has one of the passenger airbag status to let you know the status of the right front passenger indicators pictured in the following illustrations, then the frontal airbag.
Page 184: Charging System Light
Charging System Light Up-Shift Light This light comes on briefly The vehicle may have an when the ignition key is up-shift light. turned on, but the engine is not running, as a check to show it is working. It should go out once the engine is running. If it stays When this light comes on, shift to the next higher gear if on, or comes on while driving, there could be a problem weather, road, and traffic conditions allow.
Page 185: Brake System Warning Light
Brake System Warning Light If the light comes on while driving, pull off the road and stop carefully. Make sure the parking brake is fully The vehicle brake system consists of two hydraulic released. The pedal might be harder to push or, the circuits.
Page 186: Antilock Brake System (Abs) Warning Light
Antilock Brake System (ABS) Enhanced Traction System (ETS) Warning Light Indicator/Warning Light For vehicles with the For vehicles with the Antilock Brake System Enhanced Traction (ABS), this light comes on System (ETS), this light briefly when the engine is serves as an indicator started.
Page 187: Electronic Stability Control (Esc)/Traction Control System (Tcs) Indicator/Warning
See Enhanced Traction System (ETS) on page 5 10 If the light comes on and stays on, the TCS and and DIC Warnings and Messages on page 4 40 for potentially the ESC system have been disabled. Check more information. the DIC messaging to determine which system is turned off, or not working.
Page 188: Engine Coolant Temperature Warning Light
Engine Coolant Temperature Engine Coolant Temperature Gauge Warning Light The vehicle has an engine coolant This light comes on briefly temperature gauge. With while starting the vehicle. the ignition turned to ON/ RUN, this gauge shows the engine coolant temperature. If it does not, have the vehicle serviced by the dealer.
Page 189: Tire Pressure Light
Tire Pressure Light Malfunction Indicator Lamp A computer system called OBD II (On-Board For vehicles with the tire Diagnostics-Second Generation) monitors operation of pressure monitoring the fuel, ignition, and emission control systems. system, this light comes It ensures that emissions are at acceptable levels for on briefly when the engine the life of the vehicle, helping to produce a cleaner is started.
Page 190 Avoid steep uphill grades. Notice: If the vehicle is continually driven with this light on, after a while, the emission controls might If towing a trailer, reduce the amount of cargo not work as well, the vehicle fuel economy might being hauled as soon as it is possible.
Page 191: Emissions Inspection And Maintenance Programs
Make sure to fuel the vehicle with quality fuel. Poor fuel quality causes the engine not to run as efficiently as designed and can cause: stalling after start-up, stalling when the vehicle is changed into gear, misfiring, hesitation on acceleration, or stumbling on acceleration.
Page 192: Maintenance Schedule
Oil Pressure Light If the light comes on and stays on, it means that oil is not flowing through the engine properly. The vehicle could be low on oil and it might have some other system problem. Security Light For information regarding this light and the vehicle's security system, see Content Theft-Deterrent...
Page 193: Highbeam On Light
Highbeam On Light An arrow on the fuel gauge indicates the side of the vehicle the fuel door is on. This light comes on when Here are four things that some owners ask about. None the high-beam headlamps of these show a problem with the fuel gauge: are in use.
Page 194: Driver Information Center (Dic)
Driver Information Center (DIC) Press and hold the information and reset buttons at the same time for one second, then release the buttons to Your vehicle has a Driver Information Center (DIC). The enter the personalization menu. See DIC Vehicle DIC display gives you the status of many of your Personalization on page 4 45 for more information.
Page 195 TRIP A or TRIP B MPG (L/100 KM) AVG (Average) Press the information button until TRIP A or TRIP B Press the information button until MPG (L/100 KM) AVG display. These modes show the current distance displays. This mode shows how many miles per gallon traveled since the last reset for each trip odometer in (mpg) or liters per 100 kilometers (L/100 km) your either miles (mi) or kilometers (km).
Page 196: Dic Warnings And Messages
AV (Average) SPEED Tire Pressure Press the information button until AV SPEED displays. If your vehicle has a Tire Pressure Monitor System This mode shows the vehicle's average speed in miles (TPMS), the pressure for each tire can be viewed in the per hour (mph) or kilometers per hour (km/h).
Page 197: Brake Fluid
AUTO (Automatic) LIGHTS OFF CHECK GAS CAP This message displays if the automatic headlamp This message displays if the fuel cap has not been fully system is disabled with the headlamp switch. See tightened. Recheck the fuel cap to make sure that it is Automatic Headlamp System on page 4 13 for more on properly.
Page 198 ENG (Engine) PWR (Power) REDUCED ESC (Electronic Stability Control) NOT READY This message displays to inform you that the vehicle has reduced engine power to avoid damaging the If your vehicle has Electronic Stability Control (ESC), engine. Reduced engine power can affect the vehicle's this message may display briefly after starting the ability to accelerate.
Page 199: Power Steering
ICE POSSIBLE may exist if this message is displayed, so adjust your driving accordingly. This message stays on for a few This message displays when the outside air seconds after the system stops limiting wheel spin. See temperature is cold enough to create icy road Enhanced Traction System (ETS) on page 5 10 or conditions.
Page 200 SERVICE ESC (ELECTRONIC STABILITY SERVICE TRACTION CONTROL) If your vehicle has the Enhanced Traction System (ETS) or Traction Control System (TCS), this message If your vehicle has Electronic Stability Control (ESC), displays and a chime sounds when the system is not this message displays and a chime sounds if there has functioning properly.
Page 201: Dic Vehicle Personalization
SVC (Service) TIRE MONITOR TRACTION OFF If your vehicle has a Tire Pressure Monitor System If your vehicle has the Enhanced Traction System (TPMS), this message displays if a part on the TPMS is (ETS) or Traction Control System (TCS), this message not working properly.
Page 202: Entering Personalization Menu
To change feature settings, use the following procedure: UNITS Entering Personalization Menu This feature allows you to select the units of measurement in which the DIC will display the vehicle 1. Turn the ignition on while the vehicle is stopped. information.
Page 203: Unlock Horn
ON: The horn will chirp on the first press of the lock LIGHT FLASH button on the RKE transmitter. This feature, which allows the vehicle's exterior hazard/ See Remote Keyless Entry (RKE) System Operation on turn signal lighting to flash every time the lock or unlock page 3 4 for more information.
Page 204: Delay Lock
DELAY LOCK AUTO UNLK (Unlock) This feature, which delays the actual locking of the This feature, which allows the vehicle to automatically vehicle, can be enabled or disabled. When DELAY unlock certain doors, can be enabled or disabled. When LOCK appears on the display, press and hold the reset AUTO UNLK appears on the display, press and hold the button for at least one second to scroll through the reset button for at least one second to scroll through the...
Page 205 UNLK (Unlock) (Automatic EXT (Exterior) LIGHTS Transmission Only) This feature, which allows the vehicle's exterior perimeter lighting to turn on each time the unlock This screen displays only if your vehicle has an button on the Remote Keyless Entry (RKE) transmitter automatic transmission and DRIVER or ALL is selected is pressed, can be enabled or disabled.
Page 206: Audio System(S)
LANGUAGE Audio System(s) This feature allows you to select the language in which Determine which radio the vehicle has and read the the DIC will display. When LANGUAGE appears on the following pages to become familiar with its features. display, press and hold the reset button for at least one second to scroll through the available settings: WARNING: ENGLISH (default): All messages will appear in...
Page 207: Setting The Clock
Notice: Contact your dealer before adding any Setting the Clock equipment. Without Date Display Adding audio or communication equipment could interfere with the operation of the vehicle's engine, AM/FM Base Radio with a Single CD Player radio, or other systems, and could damage them. Follow federal rules covering mobile radio and To set the time: telephone equipment.
Page 208: With Date Display
With Date Display 5. To decrease the time or date do one of the following: Radio with CD (MP3) and USB Port, and © Press SEEK or REV. Radio with Single CD (MP3) Player Turn counterclockwise. To set the time and date: The date does not automatically display.
Page 209: Radio(S)
Radio(s) Radio with CD (MP3) and USB Port shown, Radio with CD (MP3) similar Radio with CD (Base) The vehicle has one of these radios as its audio system. 4-53...
Page 210: Playing The Radio
Radio Data System (RDS) 4. Press the softkey under the desired Speed Compensated Volume setting (OFF, Low, Med, The radio may have RDS. The RDS feature is available or High) to select the level of radio volume for use only on FM stations that broadcast RDS compensation.
Page 211: Storing Radio Stations
To scan preset stations in the selected band, press (Information): For vehicles with the Radio with CD © and hold SEEK for four seconds until a double (Base), press to switch the display between the radio beep sounds. The radio goes to a stored preset, station frequency and the time.
Page 212 FAV (Favorites): A maximum of 36 stations can be 3. Select the desired number of favorites pages by stored as favorites using the six softkeys located below pressing the softkey located below the displayed the radio station frequency tabs and by using the radio page numbers.
Page 213 Storing a Radio Station as a Preset To adjust the tone settings on the Radio with CD (MP3) and USB Port or the Radio with CD (MP3): Radios that have numbered pushbuttons store radio 1. Press until the tone control tabs display. stations as presets.
Page 214: Adjusting The Speakers (Balance/Fade)
EQ (Equalization): Press this button to select preset To adjust balance or fade using equalization settings. 1. Press until the speaker control labels display. To return to the manual mode, press EQ until Manual displays or start to manually adjust the bass, midrange, 2.
Page 215: Radio Messages
Finding a Category (CAT) Station Undesired XM categories can be removed through the setup menu. To remove an undesired category: (XM Satellite Radio Service Only) 1. Press MENU to display the radio setup menu. CAT (Category): The radio may have the CAT button 2.
Page 216: Loading A Cd
XM Satellite Radio Service Ejecting a CD For vehicles with XM, it is a satellite radio service EJECT: Press to eject the CD. If the CD is not that is based in the 48 contiguous United States and removed, after several seconds, the CD automatically 10 Canadian provinces.
Page 217 RDM (Random): Tracks can be listened to in random, CD Messages rather than sequential order. CHECK DISC: If an error message displays and/or the To use random: CD comes out, it could be for one of the following reasons: 1. Press the softkey below RDM tab until Random Current Disc displays.
Page 218: Care Of Cds
Care of CDs If an error displays, see CD Messages earlier in this section. Store CD(s) in their original cases or other protective Using the Auxiliary Input Jack cases and away from direct sunlight and dust. The CD player scans the bottom of the disc. If the bottom The radio system may have an auxiliary input jack of a CD is damaged it may not play properly or at all.
Page 219: Using An Mp3
® CD/AUX (CD/Auxiliary): Press to play a CD while a Make sure the iPod has the latest firmware from Apple portable audio device is connected to the auxiliary for proper operation. iPod firmware can be updated ® input. Press again and the system begins playing audio using the latest iTunes application.
Page 220 CD R or CD RW Supported File and Folder Root Directory Structure The root directory is treated as a folder. Files are stored in the root directory when the disc or storage device The radio supports: does not contain folders. Files accessed from the root Up to 50 folders.
Page 221 File System and Naming Playing a CD-R or CD-RW MP3 The song name that displays is the song name that is (Tune): Turn to select MP3 files on the CD currently contained in the ID3 tag. If the song name is not playing.
Page 222 RDM (Random): MP3 files can be listened to on a CD To listen to files by another artist, press the softkey in random, rather than sequential order. To use random, located below either arrow tab. The disc goes to the press the softkey under the RDM tab until Random next or previous artist in alphabetical order.
Page 223: Connecting A Usb Storage Device ® Or Ipod
Connecting a USB Storage Device Using the Radio to Control a USB ® or iPod Storage Device or iPod The USB Port can be used to control an iPod or a The radio can control a USB storage device or an iPod USB storage device.
Page 224: Using Softkeys To Control A Usb Storage Device Or Ipod
Using Softkeys to Control a (Folder View): Press the softkey below to view the contents of the current folder on the USB drive. To USB Storage Device or iPod browse and select files: The five softkeys below the radio display are used to 1.
Page 225 To skip through large lists, the five softkeys can be used (Music Navigator): Press the softkey below to navigate in the following order: to view and select a file on an iPod, using the iPod's menu system. Files are sorted by: First softkey, first item in the list.
Page 226: Xm Radio Messages
Shuffle Functionality No XM Signal: The system is functioning correctly, but the vehicle is in a location that is blocking the XM To use Shuffle: signal. When the vehicle is moved into an open area, the signal should return. Press the softkey below select between Shuffle Off, Shuffle All Songs/Shuffle Loading XM: The audio system is acquiring and Songs, Shuffle Album, or Shuffle Folder.
Page 227: Bluetooth
® CAT Not Found: There are no channels available for Bluetooth the selected category. The system is working properly. Vehicles with a Bluetooth system can use a Bluetooth XM Theftlocked: The XM receiver in the vehicle could capable cell phone with a Hands Free Profile to make have previously been in another vehicle.
Page 228 Audio System Pairing When using the in vehicle Bluetooth system, sound A Bluetooth cell phone must be paired to the Bluetooth comes through the vehicle's front audio system system and then connected to the vehicle before it can speakers and overrides the audio system. Use the be used.
Page 229: Pairing A Phone
Pairing a Phone Listing All Paired and Connected Phones The system can list all cell phones paired to it. If a 1. Press and hold for two seconds. paired cell phone is also connected to the vehicle, the 2. Say Bluetooth . system responds with is connected after that 3.
Page 230: Storing And Deleting Phone Numbers
Connecting to a Different Phone Digit Store: This command allows a phone number to be stored as a name tag by entering the digits one at To connect to a different cell phone, the Bluetooth a time. system looks for the next available cell phone in the Delete: This command is used to delete individual order in which all the available cell phones were paired.
Page 231: Making A Call
3. Say each digit, one at a time, that you want to Using the List Command store. After each digit is entered, the system 1. Press and hold for two seconds. repeats back the digit it heard followed by a tone. After the last digit has been entered, say Store , 2.
Page 232: Receiving A Call
Using the Digit Dial Command Receiving a Call The digit dial command allows a phone number to be When an incoming call is received, the audio system dialed by entering the digits one at a time. After each mutes and a ring tone is heard in the vehicle. digit is entered, the system repeats back the digit it Press to answer the call.
Page 233: Transferring A Call
Three Way Calling Transferring a Call Three way calling must be supported on the cell phone Audio can be transferred between the Bluetooth system and enabled by the wireless service carrier. and the cell phone. The cell phone must be paired and connected with the 1.
Page 234: Other Information
Voice Pass-Thru Sending a Number or Name Tag During a Call Voice pass thru allows access to the voice recognition commands on the cell phone. See your cell phone 1. Press . The system responds Ready , manufacturers user guide to see if the cell phone followed by a tone.
Page 235: Theft-Deterrent Feature
Theft-Deterrent Feature To change radio stations: Press and release to go to the next or ® THEFTLOCK is designed to discourage theft of the previous radio station stored as a preset. vehicle's radio by learning a portion of the Vehicle Identification Number (VIN).
Page 236: Radio Reception
3. Press and release to scroll up or down the list. The range for most AM stations is greater than for FM, especially at night. The longer range can cause station To select a folder, press and hold when the frequencies to interfere with each other.
Page 237: Fixed Mast Antenna
Cellular Phone Usage Satellite Radio Antenna System Cellular phone usage may cause interference with the vehicle's radio. This interference may occur when The XM Satellite Radio antenna is located on the roof of making or receiving phone calls, charging the phone's the vehicle.
Page 238 NOTES 4-82...
Page 239: Driving Your Vehicle
Section 5 Driving Your Vehicle Your Driving, the Road, and the Vehicle ..5-2 Driving at Night ....... . 5-16 Defensive Driving .
Page 240: Your Driving, The Road, And The Vehicle
Your Driving, the Road, and the Drunk Driving Vehicle WARNING: Defensive Driving Drinking and then driving is very dangerous. Your Defensive driving means always expect the reflexes, perceptions, attentiveness, and judgment unexpected. The first step in driving defensively is to can be affected by even a small amount of wear your safety belt See Safety Belts: They Are for...
Page 241: Control Of A Vehicle
For persons under 21, it is against the law in every Braking U.S. state to drink alcohol. There are good medical, See Brake System Warning Light on page 4 29. psychological, and developmental reasons for these laws. Braking action involves perception time and reaction time.
Page 242: Antilock Brake System (Abs)
allowing realistic following distances eliminates a lot of Antilock Brake System (ABS) unnecessary braking. That means better braking and The vehicle might have the Antilock Brake longer brake life. System (ABS), an advanced electronic braking If the engine ever stops while the vehicle is being system that helps prevent a braking skid.
Page 243: Brake Assist
ABS can change the brake pressure to each wheel, as stop rolling. Once they do, the vehicle cannot respond required, faster than any driver could. This can help the to the driver's steering. Momentum will carry it in driver steer around the obstacle while braking hard. whatever direction it was headed when the wheels stopped rolling.
Page 244: Electronic Stability Control (Esc)
until the ABS activates. Minor brake pedal pulsations or This light flashes on the pedal movement during this time is normal and the instrument panel cluster driver should continue to apply the brake pedal as the when the ESC system is driving situation dictates The Brake Assist feature will on and activated.
Page 245 The Electronic Stability Control (ESC) system is When the ESC system is turned off, the TRACTION automatically enabled whenever the vehicle is started. OFF and ESC OFF messages appear, and the ESC/ To assist the driver with vehicle directional control, TCS light comes on to warn the driver that both traction especially in slippery road conditions, always leave the control and ESC are disabled.
Page 246: Traction Control System (Tcs)
Traction Control System (TCS) If the vehicle is in cruise control while TCS begins to limit wheel spin, the cruise control will automatically The vehicle has a Traction Control System (TCS) that disengage. The cruise control can be re-engaged when limits wheel spin.
Page 247 not be covered by the vehicle warranty. Reduce To turn the system off or engine power and do not spin the wheel(s) on, press and release the excessively while these lights and this message are ESC/TCS button located displayed. on the instrument panel. Notice: When traction control is turned off, or Competitive Driving Mode is active, it is possible to lose traction.
Page 248: Enhanced Traction System (Ets)
Enhanced Traction System (ETS) The vehicle may have an Enhanced Traction System (ETS) that limits wheel spin. This is especially useful in slippery road conditions. The system operates only if it senses that one or both of the front wheels are spinning or beginning to lose traction.
Page 249: Limited-Slip Differential
If the ETS indicator/warning light comes on and R (Reverse). If the ETS is limiting wheel spin when the stays on for an extended period of time when the transmission is shifted to L (Low) or R (Reverse) to turn transmission shift lever is in any position other than the system off, the indicator/warning light and L (Low), the vehicle may need service.
Page 250: Steering
Steering If there is a need to reduce speed, do it before entering the curve, while the front wheels are straight. Electric Power Steering Try to adjust the speed so you can drive through the curve. Maintain a reasonable, steady speed. Wait to If the engine stalls while driving, the power steering accelerate until out of the curve, and then accelerate assist system will continue to operate until you are able...
Page 251: Off-Road Recovery
Off-Road Recovery The vehicle's right wheels can drop off the edge of a road onto the shoulder while driving. An emergency like this requires close attention and a quick decision. If holding the steering wheel at the recommended 9 and 3 o'clock positions, it can be turned a full 180 degrees very quickly without removing either hand.
Page 252: Passing
Passing Skidding In a skid, a driver can lose control of the vehicle. Passing another vehicle on a two-lane road can be Defensive drivers avoid most skids by taking dangerous. To reduce the risk of danger while passing: reasonable care suited to existing conditions, and by Look down the road, to the sides, and to not overdriving those conditions.
Page 253: Racing Or Other Competitive Driving
If the vehicle has Electronic Stability Control (ESC), the Racing or Other Competitive Driving ESC might activate. See Electronic Stability Control See your warranty book before using your vehicle for (ESC) on page 5 6. racing or other competitive driving. After reviewing your Of course, traction is reduced when water, snow, ice, warranty book, please see the GM Performance Parts gravel, or other material is on the road.
Page 254: Driving At Night
Driving at Night Driving in Rain and on Wet Roads Night driving is more dangerous than day driving Rain and wet roads can reduce vehicle traction and because some drivers are likely to be impaired affect your ability to stop and accelerate. Always drive alcohol or drugs, with night vision problems, or by slower in these types of driving conditions and avoid fatigue.
Page 255: Before Leaving On A Long Trip
Hydroplaning Before Leaving on a Long Trip Hydroplaning is dangerous. Water can build up under To prepare your vehicle for a long trip, consider having your vehicle's tires so they actually ride on the water. it serviced by your dealer before departing. This can happen if the road is wet enough and you are Things to check on your own include: going fast enough.
Page 256: Highway Hypnosis
Highway Hypnosis WARNING: Always be alert and pay attention to your surroundings while driving. If you become tired or sleepy, find a safe place to park your vehicle and rest. If you do not shift down, the brakes could get so hot that they would not work well.
Page 257: Winter Driving
Top of hills: Be alert something could be in your If the vehicle has the Traction Control System (TCS) on lane (stalled car, accident). page 5 8 or Enhanced Traction System (ETS) on page 5 10, it improves the ability to accelerate on Pay attention to special road signs (falling rocks slippery roads, but slow down and adjust your driving to area, winding roads, long grades, passing or...
Page 258 Blizzard Conditions WARNING: (Continued) Being stuck in snow can be in a serious situation. Stay with the vehicle unless there is help nearby. If possible, use the Roadside Assistance Program on page 8 6. Open a window about 5 cm (two inches) on To get help and keep everyone in the vehicle safe: the side of the vehicle that is away from the wind to bring in fresh air.
Page 259: If Your Vehicle Is Stuck In Sand, Mud, Ice
To save fuel, run the engine for only short periods as needed to warm the vehicle and then shut the engine WARNING: off and close the window most of the way to save heat. Repeat this until help arrives but only when you feel If the vehicle's tires spin at high speed, they can really uncomfortable from the cold.
Page 260: Loading The Vehicle
reverse directions causes a rocking motion that could Tire and Loading Information Label free the vehicle. If that does not get the vehicle out after a few tries, it might need to be towed out. If the vehicle does need to be towed out, see Towing Your Vehicle on page 5 28.
Page 261 The Tire and Loading Information label also lists The resulting figure equals the available the tire size of the original equipment tires (C) and amount of cargo and luggage load capacity. the recommended cold tire inflation pressures (D). For example, if the XXX amount equals For more information on tires and inflation, see 1400 lbs and there will be five 150 lb Tires on page 6 47 and Inflation - Tire Pressure on...
Page 262 Example 1 Example 2 Item Description Total Item Description Total Maximum Vehicle Maximum Vehicle 1,000 lbs 1,000 lbs Capacity Weight for Capacity Weight for (453 kg) (453 kg) Example 1 = Example 2 = Subtract Occupant Subtract Occupant Weight @ 150 lbs 300 lbs (136 kg) Weight @ 150 lbs 750 lbs (340 kg)
Page 263 Refer to your vehicle's tire and loading information label for specific information about your vehicle's maximum vehicle capacity weight and seating positions. The combined weight of the driver, passengers, and cargo should never exceed your vehicle's maximum vehicle capacity weight. Example 3 Item Description...
Page 264 Certification Label The label shows the size of your original tires and the inflation pressures needed to obtain the gross weight capacity of your vehicle. This is called the Gross Vehicle Weight Rating (GVWR). The GVWR includes the weight of the vehicle, all occupants, fuel, and cargo.
Page 265 WARNING: WARNING: Do not load the vehicle any heavier than the Things you put inside your vehicle can strike Gross Vehicle Weight Rating (GVWR), and injure people in a sudden stop or turn, or either the maximum front or rear Gross or in a crash.
Page 266: Towing
Towing Here are some important things to consider before recreational vehicle towing: What is the towing capacity of the towing vehicle? Towing Your Vehicle Be sure to read the tow vehicle manufacturer's Notice: To avoid damage, the disabled vehicle recommendations. should be towed with all four wheels off the ground.
Page 267: Dinghy Towing
Dinghy Towing To prevent the battery from draining while the vehicle is being towed, remove the following fuse from the floor ® console fuse block: 8 (Ignition Switch, PASS Key III+). See Floor Console Fuse Block on page 6 101 for more information.
Page 268: Dolly Towing
Dolly Towing 3. Set the parking brake and then remove the key. 4. Clamp the steering wheel in a straight-ahead position with a clamping device designed for towing. 5. Secure the vehicle to the dolly. 6. Release the parking brake. Use the following procedure to dolly tow the vehicle from the front with two wheels on the ground: 1.
Page 269: Towing A Trailer (Automatic Transmission)
Towing a Trailer (Automatic capacity of the vehicle, read the information in Weight of the Trailer that appears later in this section. Transmission) Trailering is different than just driving the vehicle by itself. Trailering means changes in handling, acceleration, braking, cooling, durability and fuel WARNING: economy.
Page 270: Pulling A Trailer
Pulling a Trailer Three important considerations have to do with weight: The weight of the trailer Here are some important points: The weight of the trailer tongue There are many different laws, including speed limit restrictions, having to do with trailering. Make The total weight on the vehicle's tires sure the rig will be legal, not only where you live Weight of the Trailer...
Page 271: Weight Of The Trailer Tongue
Weight of the Trailer Tongue Do not exceed the maximum allowable tongue weight for the vehicle. Choose the shortest hitch extension that The tongue load (A) of any trailer is an important weight will position the hitch ball closest to the vehicle. This will to measure because it affects the total gross weight of help reduce the effect of trailer tongue weight on the the vehicle.
Page 272: Driving With A Trailer
Total Weight on the Vehicle's Tires Safety Chains Be sure the vehicle's tires are inflated to the upper limit Always attach chains between the vehicle and the for cold tires. These numbers can be found on the trailer. Cross the safety chains under the tongue of the Tire-Loading Information label.
Page 273: Making Turns
Before starting, check all trailer hitch parts and Backing Up attachments, safety chains, electrical connectors, Hold the bottom of the steering wheel with one hand. lamps, tires and mirror adjustments. If the trailer has Then, to move the trailer to the left, move that hand to electric brakes, start the vehicle and trailer moving and the left.
Page 274: Driving On Grades
Driving on Grades Parking on Hills Notice: Do not tow on steep continuous grades exceeding 9.6 km (6 miles). Extended, higher than WARNING: normal engine and transmission temperatures may result and damage the vehicle. Frequent stops are very important to allow the engine and transmission Parking the vehicle on a hill with the trailer to cool.
Page 275: Towing A Trailer (Manual Transmission)
Leaving After Parking on a Hill Engine Cooling When Trailer Towing 1. Apply and hold the brake pedal while you: The cooling system may temporarily overheat during severe operating conditions. See Engine Overheating start the engine, on page 6 28. shift into a gear, and Towing a Trailer (Manual release the parking brake.
Page 276 NOTES 5-38...
Page 277: Service And Appearance Care
Section 6 Service and Appearance Care Service ..........6-3 Cooling System .
Page 278 Section 6 Service and Appearance Care When It Is Time for New Tires ....6-62 Washing Your Vehicle ......6-95 Buying New Tires .
Page 279: Service
Service Accessories and Modifications When non dealer/non retailer accessories are added to For service and parts needs, visit your dealer. You will the vehicle, they can affect vehicle performance and receive genuine GM parts and GM-trained and safety, including such things as airbags, braking, supported service people.
Page 280: California Proposition 65 Warning
California Proposition 65 Warning WARNING: (Continued) Most motor vehicles, including this one, contain and/or emit chemicals known to the State of California to cause cancer and birth defects or other reproductive Be sure you have sufficient knowledge, harm. Engine exhaust, many parts and systems, many experience, the proper replacement parts, and fluids, and some component wear by-products contain tools before attempting any vehicle...
Page 281: Adding Equipment To The Outside Of The
Adding Equipment to the Outside of the Vehicle Things added to the outside of the vehicle can affect the airflow around it. This can cause wind noise and can affect fuel economy and windshield washer performance. Check with your dealer before adding equipment to the outside of the vehicle.
Page 282: Gasoline Octane
Gasoline Octane Gasoline Specifications If the vehicle has the 2.2L L4 engine (VIN Code W), use At a minimum, gasoline should meet ASTM regular unleaded gasoline with a posted octane rating of specification D 4814 in the United States or 87 or higher.
Page 283: Additives
Additives Gasolines containing oxygenates, such as ethers and ethanol, and reformulated gasolines might be available To provide cleaner air, all gasolines in the United States in your area. We recommend that you use these are now required to contain additives that help prevent gasolines, if they comply with the specifications engine and fuel system deposits from forming, allowing described earlier.
Page 284: Fuel E85 (85% Ethanol)
Fuel E85 (85% Ethanol) starting on E85, it could be because the E85 fuel is not properly formulated for your climate. If this happens, Vehicles that have a FlexFuel badge and a yellow fuel switching to gasoline or adding gasoline to the fuel tank cap can use either unleaded gasoline or ethanol fuel can improve starting.
Page 285: Fuels In Foreign Countries
Fuels in Foreign Countries WARNING: (Continued) If you plan on driving in another country outside the United States or Canada, the proper fuel might be hard to find. Never use leaded gasoline or any other fuel not from fuel. Do not leave the fuel pump unattended recommended in the previous text on fuel.
Page 286 To remove the fuel cap, turn it slowly counterclockwise. The fuel cap has a spring in it; if the cap is released too soon, it will spring back to the right. While refueling, hang the tethered fuel cap from the hook on the fuel door.
Page 287 When replacing the fuel cap, turn it clockwise until it clicks. Make sure the cap is fully installed. The WARNING: diagnostic system can determine if the fuel cap has been left off or improperly installed. This would allow If a fire starts while you are refueling, do not fuel to evaporate into the atmosphere.
Page 288: Filling A Portable Fuel Container
Filling a Portable Fuel Container Checking Things Under the Hood WARNING: WARNING: Never fill a portable fuel container while it is in the vehicle. Static electricity discharge from the An electric fan under the hood can start up and container can ignite the fuel vapor. You can be injure you even when the engine is not running.
Page 289: Hood Release
Hood Release 2. Then go to the front of the vehicle and push To open the hood, do the following. the secondary hood release lever to the left. 1. Pull the interior hood It is located under the release lever with this front center of the symbol on it.
Page 290: Engine Compartment Overview
Engine Compartment Overview 2.4 L L4 Engine Shown, 2.2 L L4 Engine Similar 6-14...
Page 291 A. Windshield Washer Fluid Reservoir. See Adding G. Engine Oil Dipstick (Out of View). See Checking Washer Fluid under Windshield Washer Fluid on Engine Oil under Engine Oil on page 6 16. page 6 30. H. Brake Master Cylinder Reservoir. See Brakes on B.
Page 292: Engine Oil
Engine Oil 2. Pull out the dipstick and clean it with a paper towel or cloth, then push it back in all the way. Remove it To ensure proper engine performance and long life, again, keeping the tip down, and check the level. careful attention must be paid to engine oil.
Page 293 Selecting the Right Engine Oil Notice: Use only engine oil that is approved to the dexos specification or an equivalent engine oil of Selecting the right engine oil depends on both the the appropriate viscosity grade. Engine oils proper oil specification and viscosity grade: approved to the dexos specification will show the dexos...
Page 294: What To Do With Used Oil
Viscosity Grade engine at extremely low temperatures. When selecting an oil of the appropriate viscosity grade, be sure to SAE 5W-30 is the best viscosity grade for the vehicle. always select an oil that meets the required Do not use other viscosity oils such as SAE 10W 30, specification, dexos .
Page 295: Engine Oil Life System
Used oil can be a threat to the environment. If you reset the system. It is also important to check the oil change your own oil, be sure to drain all the oil from the regularly over the course of an oil drain interval and filter before disposal.
Page 296: Engine Air Cleaner/Filter
For vehicles with the 2.2L (VIN Code V) or 2.4L How to Inspect the Engine Air Cleaner/ (VIN Code B) engines, you can also reset the system Filter as follows: 1. Turn the ignition key to ON/RUN with the engine off. 2.
Page 297: Automatic Transmission Fluid
To inspect or replace the filter, do the following: Automatic Transmission Fluid 1. Disconnect the Mass Air Flow sensor, PCV hose, It is not necessary to check the transmission fluid level. and both ducts. A transmission fluid leak is the only reason for fluid 2.
Page 298: Manual Transmission Fluid
Manual Transmission Fluid Cooling System It is not necessary to check the manual transmission The cooling system allows the engine to maintain the fluid level. A transmission fluid leak is the only reason correct working temperature. for fluid loss. If a leak occurs, take the vehicle to a dealer for service.
Page 299 WARNING: WARNING: An electric engine cooling fan under the hood can Heater and radiator hoses, and other engine start up even when the engine is not running and parts, can be very hot. Do not touch them. If you can cause injury. Keep hands, clothing, and tools do, you can be burned.
Page 300: Engine Coolant
Engine Coolant Use a 50/50 mixture of clean, drinkable water and DEX-COOL coolant. If using this mixture, nothing else The cooling system in the vehicle is filled with needs to be added. This mixture: ® DEX-COOL engine coolant. This coolant is designed Gives freezing protection down to 34°F ( 37°C), to remain in the vehicle for 5 years or 240 000 km outside temperature.
Page 301 If coolant is visible but the coolant level is not at or The coolant recovery tank above the COLD FILL mark, add a 50/50 mixture of cap has this symbol on it. clean, drinkable water and DEX-COOL coolant at the The tank is located in the coolant recovery tank, but be sure the cooling system is engine compartment...
Page 302: How To Add Coolant To The Cooling System
How to Add Coolant to the Cooling WARNING: System Steam and scalding liquids from a hot cooling WARNING: system can blow out and burn you badly. They are under pressure, and if you turn the surge tank You can be burned if you spill coolant on hot pressure cap even a little they can come out...
Page 303 If no coolant is visible in the coolant recovery tank, add 4. Rinse or wipe any spilled coolant from the engine coolant at the pressure cap as follows: and the compartment. 1. Remove the pressure cap when the cooling system, including the pressure cap and upper radiator hose, is no longer hot.
Page 304: Engine Overheating
8. By this time, the coolant level inside the radiator If you do decide to lift the hood, make sure the vehicle filler port may be lower. If the level is lower, add is parked on a level surface. more of the proper DEX-COOL coolant mixture Then check to see if the engine cooling fans are through the fill port until the level reaches the base running.
Page 305 If the overheat warning is displayed with no sign of WARNING: (Continued) steam: 1. Turn the air off. 2. Turn the heater on to the highest temperature and If you keep driving when your engine is to the highest fan speed. Open the windows as overheated, the liquids in it can catch fire.
Page 306: Windshield Washer Fluid
Fill the washer fluid tank only three-quarters Windshield Washer Fluid full when it is very cold. This allows for fluid expansion if freezing occurs, which could What to Use damage the tank if it is completely full. When you need windshield washer fluid, be sure to Do not use engine coolant (antifreeze) in the read the manufacturer's instructions before use.
Page 307 Do not top off the brake/clutch fluid. Adding fluid does not correct a leak. If fluid is added when the brake WARNING: linings are worn, there will be too much fluid when new brake linings are installed. Add or remove fluid, as With the wrong kind of fluid in the brake or clutch necessary, only when work is done on the brake/clutch hydraulic system.
Page 308: Brake Adjustment
Brake Wear Properly torqued wheel nuts are necessary to help prevent brake pulsation. When tires are rotated, inspect This vehicle has front disc brakes and could have rear brake pads for wear and evenly tighten wheel nuts in drum brakes or rear disc brakes. the proper sequence to torque specifications in Capacities and Specifications on page 6 107.
Page 309: Battery
Replacing Brake System Parts DANGER: The braking system on a vehicle is complex. Its many parts have to be of top quality and work well together if the vehicle is to have really good braking. The vehicle Battery posts, terminals, and related accessories was designed and tested with top-quality brake parts.
Page 310: Jump Starting
Jump Starting Notice: If the other vehicle's system is not a 12-volt system with a negative ground, both For more information about the vehicle battery, see vehicles can be damaged. Only use vehicles with Battery on page 6 33. 12-volt systems with negative grounds to jump start If the vehicle's battery has run down, you may want to your vehicle.
Page 311 4. Open the hood on the other vehicle and locate the Locate the remote positive (+) and negative ( ) terminal locations on negative ( ) ground that vehicle. terminal, marked GND ( ), which is located at the You will not see the battery of your vehicle under front of the engine the hood.
Page 312 WARNING: WARNING: Using a match near a battery can cause battery Fans or other moving engine parts can injure you gas to explode. People have been hurt doing this, badly. Keep your hands away from moving parts and some have been blinded. Use a flashlight if once the engine is running.
Page 313 7. Do not let the other end touch metal. Connect it to the positive (+) terminal of the good battery. Use a remote positive (+) terminal if the vehicle has one. 8. Now connect the black negative ( ) cable to the negative ( ) terminal of the good battery.
Page 314: Headlamp Aiming
3. Disconnect the red positive (+) cable from the The vehicle should: vehicle with the good battery. Be placed so the headlamps are 25 ft. (7.6 m) from 4. Disconnect the red positive (+) cable from the other a light colored wall. vehicle.
Page 315 To adjust the vertical aim: 1. Open the hood. See Hood Release on page 6 13 for more information. 4. At the wall measure from the ground upward (A) to the recorded distance from Step 3 and mark it. 5. Draw or tape a horizontal line (B) on the wall the width of the vehicle at the height of the mark in 2.
Page 316 The top edge of the cut-off should be positioned at the bottom edge of the horizontal tape line. Driver Side Shown 9. Make sure that the light from the headlamp is positioned at the bottom edge of the horizontal 7. Locate the vertical headlamp aiming screws, which tape line.
Page 317: Bulb Replacement
Bulb Replacement Headlamps, Front Turn Signal, and Parking Lamps For the proper type of replacement bulbs, see Replacement Bulbs on page 6 45. For any bulb changing procedure not listed in this section, contact your dealer. Halogen Bulbs WARNING: Halogen bulbs have pressurized gas inside and can burst if you drop or scratch the bulb.
Page 318 To replace the headlamp, turn signal, or parking 3. Reach in behind the wheel well liner and locate the lamp bulb: bulb to be changed. 1. Turn the wheel to access the wheel well. 4. Turn the bulb socket counterclockwise and pull it straight out of the lamp assembly.
Page 319: Center High-Mounted Stoplamp (Chmsl)
Center High-Mounted Stoplamp (CHMSL) To replace the center high-mounted stoplamp bulb: 1. Open the liftgate. See Liftgate on page 3 11. 4. Pull the old bulb straight out of the bulb socket. 5. Push the new bulb straight into the bulb socket until it clicks.
Page 320 Taillamps, Turn Signal, Stoplamps To replace one of these bulbs: 1. Open the liftgate. See Liftgate on page 3 11. and Back-up Lamps A. Stoplamp/Taillamp/Turn Signal Lamp B. Back-up Lamp 2. Remove the cover in the rear cargo area of the vehicle to access the bulbs.
Page 321: License Plate Lamp
6. Push the bulb socket straight into the lamp 4. Push the new bulb into the bulb socket and turn it assembly and turn it clockwise to lock it into place. clockwise to lock it into place. 7. Reinstall the cover. 5.
Page 322: Windshield Wiper Blade Replacement
Windshield Wiper Blade 3. Install the new wiper blade on the wiper arm and press down on the clip to snap it into place. Replacement Backglass Wiper Blade Replacement Windshield wiper blades should be inspected for wear 1. Remove the protective cap from the wiper arm. or cracking.
Page 323 Tires WARNING: (Continued) Your new vehicle comes with high-quality tires made by a leading tire manufacturer. If you ever Over inflated tires are more likely to be have questions about your tire warranty and cut, punctured, or broken by a sudden where to obtain service, see your vehicle impact such as when you hit a pothole.
Page 324: Tire Sidewall Labeling
Tire Sidewall Labeling construction type, and service description. See the Tire Size illustration later in this Useful information about a tire is molded into its section for more detail. sidewall. The examples below show a typical passenger vehicle tire and a compact spare tire (B) TPC Spec (Tire Performance Criteria sidewall.
Page 325 (E) Tire Ply Material The type of cord and number of plies in the sidewall and under the tread. (F) Uniform Tire Quality Grading (UTQG) Tire manufacturers are required to grade tires based on three performance factors: treadwear, traction, and temperature resistance. For more information see Uniform Tire Quality Grading on page 6 65 .
Page 326: Tire Size
(B) Tire Ply Material The type of cord and (G) TPC Spec (Tire Performance Criteria number of plies in the sidewall and under the Specification) Original equipment tires designed tread. to GM's specific tire performance criteria have a TPC specification code molded onto the sidewall. (C) Tire Identification Number (TIN) The letters GM's TPC specifications meet or exceed all...
Page 327: Tire Terminology And Definitions
(C) Aspect Ratio A two digit number that Tire Terminology and Definitions indicates the tire height to width measurements. Air Pressure The amount of air inside the tire For example, if the tire size aspect ratio is 60, as pressing outward on each square inch of the tire. shown in item C of the illustration, it would mean Air pressure is expressed in pounds per square that the tire's sidewall is 60 percent as high as it...
Page 328 Cold Tire Pressure The amount of air pressure Intended Outboard Sidewall The side of an in a tire, measured in pounds per square inch (psi) asymmetrical tire, that must always face outward or kilopascals (kPa) before a tire has built up heat when mounted on a vehicle.
Page 329 Occupant Distribution Designated seating Speed Rating An alphanumeric code assigned positions. to a tire indicating the maximum speed at which a tire can operate. Outward Facing Sidewall The side of an asymmetrical tire that has a particular side that Traction The friction between the tire and the faces outward when mounted on a vehicle.
Page 330: Inflation - Tire Pressure
Vehicle Maximum Load on the Tire Load on an If your tires have too much air (over inflation), individual tire due to curb weight, accessory you can get the following: weight, occupant weight, and cargo weight. Unusual wear. Vehicle Placard A label permanently attached to Poor handling.
Page 331: How To Check
When to Check If you overfill the tire, release air by pushing on the metal stem in the center of the tire valve. Check your tires once a month or more. Do not Re check the tire pressure with the tire gauge. forget to check the compact spare tire, it should Be sure to put the valve caps back on the valve be at 60 psi (420 kPa).
Page 332 Accordingly, when the low tire pressure telltale When the malfunction indicator is illuminated, the illuminates, you should stop and check your tires as system may not be able to detect or signal low tire soon as possible, and inflate them to the proper pressure as intended.
Page 333: Tire Pressure Monitor Operation
Tire Pressure Monitor Operation viewed by the driver. For additional information and details about the DIC operation and displays see DIC This vehicle may have a Tire Pressure Monitor System Operation and Displays on page 4 38 and DIC (TPMS). The TPMS is designed to warn the driver when Warnings and Messages on page 4 40.
Page 334: Tpms Malfunction Light And Message
The TPMS sensor matching process was started Factory-installed Tire Inflator Kits use a GM approved but not completed or not completed successfully liquid tire sealant. Using non-approved tire sealants after rotating the vehicle's tires. The DIC message could damage the TPMS sensors. See Tire Sealant and and TPMS malfunction light should go off once the Compressor Kit on page 6 70 for information regarding TPMS sensor matching process is performed...
Page 335: Tpms Sensor Matching Process
TPMS Sensor Matching Process 3. Press and hold the Remote Keyless Entry (RKE) transmitter's LOCK and UNLOCK buttons, at the Each TPMS sensor has a unique identification code. same time, for about five seconds to start the Any time you replace one or more of the TPMS sensors TPMS learn mode.
Page 336: Tire Inspection And Rotation
8. The driver side rear turn signal comes on to Always remove the tires if any of the following indicate that corner sensor is ready to be learned. statements are true: Proceed to the driver side rear tire, and repeat the You can see the indicators at three or more procedure in Step 5.
Page 337 Any time you notice unusual wear, rotate the tires Reset the Tire Pressure Monitor System. See Tire as soon as possible and check wheel alignment. Pressure Monitor Operation on page 6 57 . Also check for damaged tires or wheels. See Make certain that all wheel nuts are properly When It Is Time for New Tires on page 6 62 and tightened.
Page 338: When It Is Time For New Tires
When It Is Time for New Tires Vehicle Storage Tires age when stored normally mounted on a parked Various factors, such as maintenance, temperatures, vehicle. Park a vehicle that will be stored for at least a driving speeds, vehicle loading, and road conditions month in a cool, dry, clean area away from direct influence when you need new tires.
Page 339 GM's exclusive TPC Spec system considers over WARNING: a dozen critical specifications that impact the overall performance of your vehicle, including brake system performance, ride and handling, Tires could explode during improper service. You traction control, and tire pressure monitoring or others could be injured or killed if you attempt performance.
Page 340 Vehicles that have a tire pressure monitoring WARNING: system could give an inaccurate low pressure warning if non TPC Spec rated tires are installed on your vehicle. Non TPC Spec rated tires may If you use bias-ply tires on the vehicle, the give a low pressure warning that is higher or lower wheel rim flanges could develop cracks after than the proper warning level you would get with...
Page 341: Different Size Tires And Wheels
Different Size Tires and Wheels Uniform Tire Quality Grading Quality grades can be found where applicable on If you add wheels or tires that are a different size than your original equipment wheels and tires, this could the tire sidewall between tread shoulder and affect the way your vehicle performs, including its maximum section width.
Page 342 All Passenger Car Tires Must Conform to Federal braking traction tests, and does not include Safety Requirements In Addition To These acceleration, cornering, hydroplaning, or peak Grades. traction characteristics. Treadwear Temperature A, B, C The treadwear grade is a comparative rating The temperature grades are A (the highest), B, based on the wear rate of the tire when tested and C, representing the tire's resistance to the...
Page 343: Wheel Alignment And Tire Balance
Wheel Alignment and Tire Balance If you need to replace any of your wheels, wheel bolts, wheel nuts, or Tire Pressure Monitor System (TPMS) The tires and wheels on your vehicle were aligned and sensors, replace them only with new GM original balanced carefully at the factory to give you the longest equipment parts.
Page 344: Tire Chains
Used Replacement Wheels WARNING: (Continued) WARNING: Use another type of traction device only if its manufacturer recommends it for use on the Putting a used wheel on the vehicle is dangerous. vehicle and tire size combination and road You cannot know how it has been used or how far conditions.
Page 345 A rear blowout, particularly on a curve, acts much like a skid and may require the same correction you would WARNING: use in a skid. In any rear blowout remove your foot from the accelerator pedal. Get the vehicle under control by Lifting a vehicle and getting under it to do steering the way you want the vehicle to go.
Page 346: Tire Sealant And Compressor Kit
Tire Sealant and Compressor Kit WARNING: WARNING: Storing the tire sealant and compressor kit or other equipment in the passenger compartment of Idling a vehicle in an enclosed area with poor the vehicle could cause injury. In a sudden stop or ventilation is dangerous.
Page 347 The kit includes: Tire Sealant Read and follow the safe handling instructions on the label adhered to the compressor. Check the tire sealant expiration date on the sealant canister. The sealant canister should be replaced before its expiration date. Replacement sealant canisters are available at your local dealer.
Page 348: Punctured Tire
Using the Tire Sealant and Compressor If a tire goes flat, avoid further tire and wheel damage by driving slowly to a level place. Turn on the hazard Kit to Temporarily Seal and Inflate a warning flashers. See Hazard Warning Flashers on Punctured Tire page 4 3.
Page 349 6. Plug the power plug (G) into the accessory power 10. Inflate the tire to the recommended inflation outlet in the vehicle. Unplug all items from other pressure using the pressure gauge (D). The accessory power outlets. See Accessory Power recommended inflation pressure can be found on Outlet(s) on page 4 15.
Page 350 12. Unplug the power plug (G) from the accessory 19. Stop at a safe location and check the tire pressure. power outlet in the vehicle. Refer to Steps 1 through 11 under Using the Tire Sealant and Compressor Kit without Sealant to 13.
Page 351 Using the Tire Sealant and Compressor See If a Tire Goes Flat on page 6 68 for other important safety warnings. Kit without Sealant to Inflate a Tire (Not Always do a safety check first. See If a Tire Goes Flat Punctured) on page 6 68.
Page 352 6. Plug the power plug (G) into the accessory power The pressure gauge (D) may read higher than the outlet in the vehicle. Unplug all items from other actual tire pressure while the compressor is on. accessory power outlets. See Accessory Power Turn the compressor off to get an accurate Outlet(s) on page 4 15.
Page 353: Removal And Installation Of The Sealant Canister
Removal and Installation of the Sealant 3. Pull up on the canister (A) to remove it. Canister 4. Replace with a new canister which is available from your dealer. To remove the sealant canister: 5. Push the new canister into place. 6.
Page 354: Tire Sealant And Compressor Kit Storage
Tire Sealant and Compressor Kit Changing a Flat Tire Storage If a tire goes flat, avoid further tire and wheel damage by driving slowly to a level place. Turn on the hazard The tire sealant and compressor kit is located in the warning flashers.
Page 355 WARNING: (Continued) 3. Turn off the engine and do not restart while the vehicle is raised. 4. Do not allow passengers to remain in the vehicle. To be even more certain the vehicle will not move, you should put blocks at the front and rear of the tire farthest away from the one being changed.
Page 356: Removing The Spare Tire And Tools
Removing the Spare Tire and Tools The jack, wheel wrench, and spare tire are stowed in the rear of the vehicle, underneath the floor of the cargo area. To remove the spare tire and tools: 1. Open the liftgate. See Liftgate on page 3 11 for more information.
Page 357 The tools needed are the jack (A) and wheel wrench (B). Turn the plastic wheel nut counterclockwise to loosen the wheel wrench from the jack. 6-81...
Page 358 Removing the Flat Tire and Installing the Spare Tire 1. Do a safety check before proceeding. See Changing a Flat Tire on page 6 78 for more information. Press the button and then pull on the end of the wheel wrench to extend the handle.
Page 359 WARNING: Getting under a vehicle when it is jacked up is dangerous. If the vehicle slips off the jack, you could be badly injured or killed. Never get under a vehicle when it is supported only by a jack. WARNING: Raising your vehicle with the jack improperly positioned can damage the vehicle and even make the vehicle fall.
Page 360 5. Remove all the wheel nuts and take off the flat tire. 4. Raise the vehicle by turning the jack handle WARNING: clockwise. Raise the vehicle far enough off the ground so there is enough room for the compact spare tire to fit underneath the wheel well. Rust or dirt on a wheel, or on the parts to which it is fastened, can make wheel nuts become loose after time.
Page 361 6. Remove any rust or dirt from the wheel bolts, mounting surfaces and spare wheel. 7. Place the compact spare tire on the wheel-mounting surface. WARNING: 9. Lower the vehicle by turning the jack handle counterclockwise. Lower the jack completely. Never use oil or grease on bolts or nuts because the nuts might come loose.
Page 362 10. Tighten the wheel nuts WARNING: firmly in a crisscross sequence as shown. Wheel nuts that are improperly or incorrectly tightened can cause the wheels to become loose or come off. The wheel nuts should be tightened with a torque wrench to the proper torque specification after replacing.
Page 363: Storing A Flat Or Spare Tire And Tools
Storing a Flat or Spare Tire and Storing the Flat Tire and Tools Tools To store the flat tire: 1. Open the liftgate. See Liftgate on page 3 11 for more information. WARNING: 2. Put back all tools as they were stored in the rear storage compartment and put the compartment Storing a jack, a tire, or other equipment in the cover back on.
Page 364 5. Route the loop end of the strap (C) through one of the cargo tie-downs (A) located in the rear of the vehicle. 6. Route the hook (B) through the loop (C). 7. Pull the strap to tighten it around the cargo tie-down (A).
Page 365 9. Attach the strap to the cargo tie-downs in the rear of the vehicle. 10. Slide the buckle to tighten the tie-down strap. Steel Wheel 8. Route the hook end of the strap through the wheel. 6-89...
Page 366 Storing the Compact Spare Tire and 1. Open the liftgate. See Liftgate on page 3 11 for more information. Tools 2. Install the strap (F) on the floor of the spare tire Use the diagram as a guide for storing the compact compartment.
Page 367: Compact Spare Tire
Compact Spare Tire Notice: When the compact spare is installed, do not take the vehicle through an automatic car wash with guide rails. The compact spare can get caught on WARNING: the rails which can damage the tire, wheel and other parts of the vehicle.
Page 368: Appearance Care
Appearance Care Notice: Using abrasive cleaners when cleaning glass surfaces on the vehicle, could scratch the glass and/or cause damage to the rear window Interior Cleaning defogger. When cleaning the glass on the vehicle, use only a soft cloth and glass cleaner. The vehicle's interior will continue to look its best if it is cleaned often.
Page 369: Fabric/Carpet
Laundry detergents or dishwashing soaps with To clean: degreasers can leave residue that streaks and 1. Saturate a lint-free, clean white cloth with water or attracts dirt. For liquid cleaners, about 20 drops per club soda. gallon (3.78 L) of water is a good guide. Use only mild, neutral-pH soaps.
Page 370: Leather
Leather Instrument Panel, Vinyl, and Other Plastic Surfaces Leather, and lighter colored leather in particular, will need more frequent cleaning to prevent the buildup of A soft cloth dampened with water may be used to dust, dirt, and colors transferred from other items so remove dust.
Page 371: Care Of Safety Belts
Care of Safety Belts should not be used on plastic parts, do not use it on the vehicle or damage may occur and it would not Keep belts clean and dry. be covered by the warranty. Do not wash the vehicle in direct sunlight. Use a car WARNING: washing soap.
Page 372: Finish Care
Finish Care Protecting Exterior Bright Metal Parts Bright metal parts should be cleaned regularly to keep Occasional waxing or mild polishing of the vehicle by their luster. Washing with water is all that is usually hand may be necessary to remove residue from the needed.
Page 373: Aluminum Or Chrome-Plated Wheels
Aluminum or Chrome-Plated Wheels The surface of these wheels is similar to the painted surface of the vehicle. Do not use strong soaps, and Trim chemicals, abrasive polishes, abrasive cleaners, cleaners with acid, or abrasive cleaning brushes on The vehicle may have either aluminum or them because they could damage the surface.
Page 374: Sheet Metal Damage
Tires Underbody Maintenance To clean the tires, use a stiff brush with tire cleaner. Chemicals used for ice and snow removal and dust control can collect on the underbody. If these are not Notice: Using petroleum-based tire dressing removed, corrosion and rust can develop on the products on the vehicle may damage the paint finish underbody parts such as fuel lines, frame, floor pan, and/or tires.
Page 375: Vehicle Identification
Vehicle Identification Engine Identification The eighth character in the VIN is the engine code. This Vehicle Identification Number (VIN) code identifies the vehicle's engine, specifications, and replacement parts. See Engine Specifications under Capacities and Specifications on page 6 107 for the vehicle's engine code.
Page 376: Electrical System
Electrical System Headlamp Wiring The headlamp wiring is protected by fuses in the fuse Add-On Electrical Equipment block. An electrical overload will cause the lamps to turn off. If this happens, have the headlamp wiring checked Notice: Do not add anything electrical to the vehicle right away.
Page 377: Fuses And Circuit Breakers
Fuses and Circuit Breakers Floor Console Fuse Block The wiring circuits in the vehicle are protected from short circuits by a combination of fuses, circuit breakers and fusible thermal links. This greatly reduces the chance of damage caused by electrical problems. Look at the silver-colored band inside the fuse.
Page 378 Fuses Usage Fuse Puller Empty Empty Empty Empty Amplifier Cluster ® Ignition Switch, PASS-Key III+ Stoplamp Heating, Ventilation, Air Conditioning, ® PASS-Key III+ Empty Empty Airbag Empty Windshield Wiper Climate Control System, Ignition, Rear View Camera Power Windows Empty 6-102...
Page 379 Fuses Usage Relays Usage Electric Power Steering, Steering Climate Control System Wheel Control Empty Sunroof Retained Accessory Power (RAP) Empty Empty Audio System XM Radio , OnStar Engine Control Module, Transmission Control Module Door Locks Interior Lights Steering Wheel Control Illumination Empty 6-103...
Page 380: Engine Compartment Fuse Block
Engine Compartment Fuse Block Fuses Usage Electric Power Steering The underhood fuse block is located on the driver side of the engine compartment. Lift the cover to access the Rear Defogger fuse/relay block. Empty Notice: Spilling liquid on any electrical component Body Control Module 3 on the vehicle may damage it.
Page 381 Fuses Usage Fuses Usage Power Outlet Horn Daytime Running Lamps Antilock Brake System (Option) Empty Instrument Panel, Ignition Emissions Driver Side High-Beam Power Windows Canister Vent Power Seat (Option) Driver Side Low-Beam Cooling Fan Passenger Side Low-Beam Engine Control Module Passenger Side High-Beam Empty Parking Lamps...
Page 382 A Center High-Mounted Stoplamp Relay, and a Rear Relays Usage Access Panel Door Interlock Relay (Panel Van only), Empty are located underhood in front of the left shock tower. Empty The Left Rear Access Panel Door Relay (Panel Van Windshield Washer Pump Only), and the Right Rear Access Panel Door Relay (Panel Van Only) are located in the rear of the vehicle Rear Windshield Washer...
Page 383: Capacities And Specifications
Capacities and Specifications The following approximate capacities are given in English and metric conversions. Please refer to Maintenance Replacement Parts on page 7 10 for more information. Capacities Application English Metric For the air conditioning system refrigerant charge Air Conditioning Refrigerant R134a amount, see the refrigerant label located under the hood.
Page 384 Engine Specifications Engine VIN Code Transmission Spark Plug Gap Automatic 2.2L L4 Engine 0.040 in (1.01 mm) Manual Automatic 2.4L L4 Engine 0.040 in (1.01 mm) Manual 6-108...
Page 385 Section 7 Maintenance Schedule Maintenance Schedule ......7-2 Recommended Fluids and Lubricants ... 7-8 Introduction .
Page 386: Maintenance Schedule
are driven on reasonable road surfaces within legal Maintenance Schedule driving limits. use the recommended fuel. See Gasoline Octane Introduction on page 6 6. Maintenance intervals, checks, inspections, recommended fluids, and lubricants are necessary WARNING: to keep this vehicle in good working condition. Damage caused by failure to follow scheduled maintenance might not be covered by the vehicle Performing maintenance work on a vehicle can be...
Page 387: Scheduled Maintenance
Rotation of New Tires Every Engine Oil Change To maintain ride, handling, and performance of the Change engine oil and filter. Reset oil life system. vehicle, it is important that the first rotation service for See Engine Oil on page 6 16 and Engine Oil Life new tires be performed.
Page 388: Additional Required Services
Fluids visual leak check (or every 12 months, Additional Required Services whichever occurs first). A leak in any system must be repaired and the fluid level checked. Every 12 000 km/7,500 Miles Engine air cleaner filter inspection. See Engine Air Rotate tires.
Page 389 Once a Year First Engine Oil Change After Every 40 000 km/25,000 Miles Starter switch check. See Owner Checks and Services on page 7 6. Passenger compartment air filter replacement (or every 24 months, whichever occurs first). More Automatic transmission shiftlock control function frequent replacement may be needed if you drive check.
Page 390: Owner Checks And Services
Evaporative control system inspection. Check all Owner Checks and Services fuel and vapor lines and hoses for proper hook up, Starter Switch Check routing, and condition. Check that the purge valve, if the vehicle has one, works properly. Replace as needed.
Page 391: Ignition Transmission Lock Check
Automatic Transmission Shift Lock 3. With the engine off, turn the ignition to ON/RUN, but do not start the engine. Without applying the Control Function Check regular brake, try to move the shift lever out of P (Park) with normal effort. If the shift lever moves out of P (Park), contact your dealer for service.
Page 392: Recommended Fluids And Lubricants
Parking Brake and Automatic Recommended Fluids and Transmission P (Park) Mechanism Lubricants Check Fluids and lubricants identified below by name, part number, or specification can be obtained from your dealer. WARNING: Usage Fluid/Lubricant The engine requires engine oil When you are doing this check, the vehicle could approved to the dexos specification.
Page 393 Usage Fluid/Lubricant Usage Fluid/Lubricant Windshield Chassis Lubricant (GM Part No. ® Optikleen Washer Solvent. Washer Chassis U.S. 12377985, in Canada 88901242) Lubrication or lubricant meeting requirements of Chassis Lubricant (GM Part No. NLGI #2, Category LB or GC-LB. Parking Brake U.S.
Page 394: Maintenance Replacement Parts
Maintenance Replacement Parts Replacement parts identified below by name, part number, or specification can be obtained from your dealer. Maintenance Replacement Parts Part GM Part Number ACDelco Part Number Engine Air Cleaner/Filter 2.2L and 2.4L Engines 22731072 A3054C Engine Oil Filter 12605566 PF457G Passenger Compartment Air Filter...
Page 395: Engine Drive Belt Routing
Engine Drive Belt Routing Dotted line shows routing for vehicles without air conditioning. 7-11...
Page 396: Maintenance Record
Maintenance Record After the scheduled services are performed, record the date, odometer reading, who performed the service, and the type of services performed in the boxes provided. Retain all maintenance receipts. Maintenance Record Odometer Date Serviced By Services Performed Reading 7-12...
Page 397 Maintenance Record (cont'd) Odometer Date Serviced By Services Performed Reading 7-13...
Page 398 Maintenance Record (cont'd) Odometer Date Serviced By Services Performed Reading 7-14...
Page 399 Section 8 Customer Assistance Information Customer Assistance and Information ... 8-2 Reporting Safety Defects ......8-13 Customer Satisfaction Procedure .
Page 400: Customer Assistance And Information
Your satisfaction and goodwill are important to your plate at the top left of the instrument panel and dealer and to Chevrolet. Normally, any concerns with visible through the windshield. the sales transaction or the operation of the vehicle will Dealership name and location.
Page 401 action, use of the program is free of charge and your Arbitration Program. General Motors of Canada Limited case will generally be heard within 40 days. If you do has committed to binding arbitration of owner disputes not agree with the decision given in your case, you may involving factory-related vehicle service claims.
Page 402: Online Owner Center
Store online service and maintenance records My Dealers: Save details such as address Chevrolet dealer locator for service nationwide and phone number for each of your preferred Exclusive privileges and offers GM dealers.
Page 403: Customer Assistance For Text Telephone (Tty)
1908 Colonel Sam Drive Oshawa, Ontario L1H 8P7 Chevrolet encourages customers to call the toll-free www.gm.ca number for assistance. However, if a customer wishes to write or e-mail Chevrolet, the letter should be 1-800-263-3777 (English) addressed to: 1-800-263-7854 (French) 1-800-263-3830 (For Text Telephone...
Page 404: Calling For Assistance
Mexico, Central America, and For more information on the limited offer, visit www.gmmobility.com or call the GM Mobility Assistance Caribbean Islands/Countries (Except Center at 1-800-323-9935. Text telephone (TTY) users, Puerto Rico and U.S. Virgin Islands) call 1-800-833-9935. General Motors de Mexico, S. de R.L. de C.V. General Motors of Canada also has a Mobility Program.
Page 405: Services Not Included In Roadside Assistance
Emergency Tow From a Public Road or Coverage Highway: Tow to the nearest Chevrolet dealer for Services are provided up to 5 years/160 000 km warranty service, or if the vehicle was in a crash (100,000 miles), whichever comes first.
Page 406: Scheduling Service Appointments
Alternative Service: If assistance cannot be Services Specific to Canadian provided right away, the Roadside Assistance Purchased Vehicles advisor may give permission to get local emergency road service. You will receive payment, Fuel Delivery: Reimbursement is approximately up to $100, after sending the original receipt to $5 Canadian.
Page 407: Courtesy Transportation Program
Courtesy Transportation Program Transportation Options Warranty service can generally be completed while you To enhance your ownership experience, we and our wait. However, if you are unable to wait, GM helps to participating dealers are proud to offer Courtesy minimize your inconvenience by providing several Transportation, a customer support program for vehicles transportation options.
Page 408: Collision Damage Repair
Public Transportation or Fuel coverage, credit card, etc. You are responsible for fuel usage charges and may also be responsible for taxes, Reimbursement levies, usage fees, excessive mileage, or rental usage If your vehicle requires overnight warranty repairs, and beyond the completion of the repair. public transportation is used instead of the dealer's It may not be possible to provide a like vehicle as a shuttle service, the expense must be supported by...
Page 409: Repair Facility
Collision Parts GM New Vehicle Limited Warranty, and any vehicle failure related to such parts is not covered by that Genuine GM Collision parts are new parts made with warranty. the same materials and construction methods as the Repair Facility parts with which your vehicle was originally built.
Page 410: If A Crash Occurs
Insurance company and policy number If your vehicle is leased, the leasing company may require you to have insurance that ensures repairs with General description of the damage to the other Genuine GM Original Equipment Manufacturer (OEM) vehicle parts or Genuine Manufacturer replacement parts. Read Choose a reputable repair facility that uses quality your lease carefully, as you may be charged at the end replacement parts.
Page 411: Reporting Safety Defects
Remember, if your vehicle is leased, you may be and remedy campaign. However, NHTSA cannot obligated to have the vehicle repaired with Genuine GM become involved in individual problems between parts, even if your insurance coverage does not pay the you, your dealer, or General Motors.
Page 412: Detroit, Mi
Call 1-800-222-1020, or write: your vehicle. Chevrolet Motor Division Owner Information Chevrolet Customer Assistance Center Owner publications are written specifically for owners P.O. Box 33170 and intended to provide basic operational information Detroit, MI 48232-5170 about the vehicle.
Page 413: Vehicle Data Recording And Privacy
Current and Past Models Vehicle Data Recording and Privacy Technical Service Bulletins and Manuals are available for current and past model GM vehicles. Your GM vehicle has a number of sophisticated ORDER TOLL FREE: 1-800-551-4123 computers that record information about the vehicle s Monday - Friday 8:00 AM - 6:00 PM performance and how it is driven.
Page 414: Event Data Recorders
Event Data Recorders Important: EDR data is recorded by your vehicle only if a non-trivial crash situation occurs; no data is recorded This vehicle has an Event Data Recorder (EDR). The by the EDR under normal driving conditions and no main purpose of an EDR is to record, in certain crash or personal data (e.g., name, gender, age, and crash near crash-like situations, such as an airbag...
Page 415: Radio Frequency Identification (Rfid)
® OnStar Radio Frequency Statement If your vehicle is equipped with an active OnStar This vehicle has systems that operate on a radio system, that system may also record data in crash or frequency that comply with Part 15 of the Federal near crash like situations.
Page 416 NOTES 8-18...
Page 417: Adding Equipment To Your Airbag-Equipped
Antenna Fixed Mast ........4-81 Accessories and Modifications .
Page 418 Audio System ........4-50 Break-In, New Vehicle .
Page 419: Securing A Child Restraint In A Rear Seat
Care of Cleaning Aluminum or Chrome-Plated Wheels ... . . 6-97 Safety Belts ........6-95 Cargo, Rear Side Door .
Page 420 Convenience Net ........3-46 Door Coolant Automatic Door Lock ......3-10 Engine .
Page 421 Engine (cont.) Exhaust ......... . 3-34 E85 Fuel .
Page 422 Fluid Automatic Transmission ......6-21 Gasoline Windshield Washer ....... 6-30 Octane .
Page 423 Heated Seats ........2-7 Integrated Trailer Brake Control Heater .
Page 424 Lighting Locks (cont.) Power Door ........3-9 Entry/Exit .
Page 425 Mirrors Outside Automatic Dimming Rearview ..... 3-36 Convex Mirror ........3-38 Manual Rearview .
Page 426: Replacing Restraint System Parts After A
Power Rear Compartment Storage Panel/Cover ..3-44 Door Locks ........3-9 Rear Door Security Locks .
Page 427: Securing A Child Restraint
Retained Accessory Power (RAP) ....3-24 Sealant Kit, Tire ........6-70 Seatback, Folding Passenger .
Page 428 Shifting Stuck in Sand, Mud, Ice, or Snow ....5-21 Sun Visors ......... 3-17 Out of Park .
Page 429: Traction System
Tires (cont.) Transmission Operation, Automatic ....3-26 Inspection and Rotation ......6-60 Transmission Operation, Manual .
Page 430 Windshield Washer ..........4-6 Warning Lights, Gauges, and Indicators .

Chevrolet HHR 2011 Owner's Manual

Section 3 Features and Controls

Section 4 Instrument Panel

Section 5 Driving Your Vehicle

Section 6 Service and Appearance Care

Quick Links

Chapters

Related Manuals for Chevrolet HHR 2011

Summary of Contents for Chevrolet HHR 2011