Table of Contents
Advertisement
EN
At the correct storage temperature, the battery
should be maintenance-charged every four
months.
The battery acid is extremely corrosive
and can cause injuries and damage to
skin and clothing. Always use rubber
gloves and glasses (goggles) to protect
your eyes. Avoid inhaling any acid
vapour.
Do not incline the battery too much so
that the battery acid can run out onto
hands or clothing. If this should hap
3 ASSEMBLY
To avoid injury and damage to people
and property, do not use the machine
until all the measures below have been
carried out..
3.1 Accessories bag
The machine is supplied with a plastic bag contain-
ing components which shall be used during the as-
sembly. The bag contains (fig. 1):
Pos. No. Designation
A
1
Gear lever (not 4135H, 4155H, 4WD)
B
Spare key
C
1
Tension pin
D
1
Shim washer
E
1
Shim washer
F
2
Shoulder washer
G
2
Screw
H
2
Screw knob
I
4
Washer
J
1
Drawing plate
K
4
Screw
L
2
Nut
M
2
Screw for battery
N
2
Nut for battery
3.2 Engine casing
To fill with fuel and to inspect and maintain the en-
gine and battery, open the engine casing.
The engine must not be running when
the casing is opened.
3.2.1 Opening
1. Raise the seat lock (fig. 2) and fold the seat for-
wards.
2. Pull up the rubber strap at the front edge of the
casing (fig. 3).
3. Grasp the front edge of the engine casing and
fold up the casing (fig. 4).
10
ENGLISH
3.2.2 Closing
1. Grasp the front edge of the engine casing and
fold down the casing (fig. 4).
2. Secure the front edge of the casing with the rub-
ber strap (fig. 3).
3.3 Battery
See
3.4 Seat, fig. 6
Release the catch (S) and fold up the seat bracket.
Install the mounting in the rear (upper) holes as
follows:
1. Install the shoulder washers (F) on the screws
(K).
2. Insert the screws through the slots in the brack-
et. Place a washer (I) between the seat and the
bracket.
3. Tighten the screws in the seat. Tightening
torque: 9±1.7 Nm.
Dimension
6 x 36
4. Check that the seat moves easily in the slots in
16 x 38 x 0.5
the bracket.
16 x 38 x 1.0
Install the mounting in the front (lower) holes as
follows:
8 x 20
1. Install the screw knobs (H) on the screws (G).
2. Install a washer (I) on each screw.
8.4 x 24 x 1.5
3. Insert the screws through the slots in the bracket
and tighten by hand in the seat.
8 x 20
4. Fold the seat down and place it in the desired
position.
5. Tighten the screw knobs (H) by hand.
The seat can be folded. If the machine is parked
outside when it is raining, fold the seat forward to
protect the seat cushion from getting wet.
The seat is locked. To fold the seat up or down, re-
lease the catch (S).
3.5 Steering wheel
See fig. 7. In order to minimise the axial play in the
steering column, the shim washers (D) and/or (E)
must be installed on the steering column between
the steering column jacket and the bracket as fol-
lows.
The machine may not be operated un-
less the engine casing is closed and
locked. Risk of burns and crushing in-
juries.
"
".
7.8
If the screws are tightened more than
9±1.7 Nm, the seat will be damaged.
The screw knobs (H) and the seat will
be damaged if tools are used.
Advertisement
Table of Contents
