Related Manuals for HALE UMC32+
Summary of Contents for HALE UMC32+
- Page 1 UMC32+ DIY USB-MIDI Controller USER MANUAL Firmware v3.1.0 / Hardware v1.1 ©2008 – 2011 Hale Microsystems LLC, All Rights Reserved.
-
Page 2: Product Description
Please pay attention to the section discussing the safe handling and how to avoid electrostatic discharge (ESD). Failure to observe the recommendations may result in damage to your UMC32+ and void your warranty. Firmware v3.1.0, Hardware v1.1, Datasheet: 03/20/2011 1:37 PM / © 2008-20011 Hale Microsystems LLC, http://www.halemicro.com... -
Page 3: Status Indicator Led (Cn11)
UMCs in the same order this method has proven to be a consistent way of identifying each UMC that is connected to your system. Firmware v3.1.0, Hardware v1.1, Datasheet: 03/20/2011 1:37 PM / © 2008-20011 Hale Microsystems LLC, http://www.halemicro.com... -
Page 4: Linking Of Two Umc's For 64 Io's (Cn6)
It is also important to note that this test mode will not overwrite any of your configuration settings as only the configuration utility will do that. Firmware v3.1.0, Hardware v1.1, Datasheet: 03/20/2011 1:37 PM / © 2008-20011 Hale Microsystems LLC, http://www.halemicro.com... -
Page 5: I/O Setup Using The Configuration Utility
In the “MIDI Ports” section, select the IN Device, and the corresponding OUT device. If you are using Windows XP the UMC32+ will show up as “USB Audio Device”, under Vista and Windows 7 it will show up as “UMC32+_D0x”, where x is the device number. -
Page 6: Configuration Utility Controls And Settings
MIDI channel to a UMC and stick with it. As it is impossible to guarantee the order which multiple UMC32 will enumerate with Windows a full proof way to consistently identify an assigned I/O is by its MIDI channel. Firmware v3.1.0, Hardware v1.1, Datasheet: 03/20/2011 1:37 PM / © 2008-20011 Hale Microsystems LLC, http://www.halemicro.com... -
Page 7: General Precautions
In the United States, this pertains to FCC rules and regulations, Part 15, Section B. Firmware v3.1.0, Hardware v1.1, Datasheet: 03/20/2011 1:37 PM / © 2008-20011 Hale Microsystems LLC, http://www.halemicro.com... -
Page 8: Example Connections
UMC, here are a few examples of how to connect the most common types. * Please note that connection to +5V is not necessary for any SPST switch. Firmware v3.1.0, Hardware v1.1, Datasheet: 03/20/2011 1:37 PM / © 2008-20011 Hale Microsystems LLC, http://www.halemicro.com... -
Page 9: Umc32+ I/O Pin Diagram
UMC32+ DIY USB-MIDI User Manual UMC32+ I/O Pin Diagram UMC32+ in picture above with attached ribbon cable Ribbon cable kit sold separately (Part # RIB50) Firmware v3.1.0, Hardware v1.1, Datasheet: 03/20/2011 1:37 PM / © 2008-20011 Hale Microsystems LLC, http://www.halemicro.com... - Page 10 2X faster than a single processor. It should be noted that the UMC that is connected to the USB bus is the Master, while the linked UMC is the slave. Firmware v3.1.0, Hardware v1.1, Datasheet: 03/20/2011 1:37 PM / © 2008-20011 Hale Microsystems LLC, http://www.halemicro.com...
-
Page 11: Mechanical Specifications
Operating voltage (power supplied via USB bus): 5.1 Volts DC max Max recommended current per I/O channel Maximum device current: *500mA USB Bus Powered, 2A external. Firmware v3.1.0, Hardware v1.1, Datasheet: 03/20/2011 1:37 PM / © 2008-20011 Hale Microsystems LLC, http://www.halemicro.com... -
Page 12: Limited Warranty
Limited Warranty Hale Microsystems LLC warrants this product to be free of manufacturing defects for a period of 90 days (USA only). If you feel that there is a defect with your device, please email technical support with a detailed description of the problem: support@halemicro.com.