COLOR TV SERVICE MANUAL CHASSIS : MP-015A MODEL : PE/PL-43/48/53A82T CAUTION BEFORE SERVICING THE CHASSIS, READ THE SAFETY PRECAUTIONS IN THIS MANUAL. MOVIE SPOR MOVIE SPORTS MUSIC TS MUSIC PRO LOGIC LOGIC DIGITAL INDEX CATV TV / Sep.,2001...
SAFETY PRECAUTIONS IMPORT ANT SAFETY NOTICE Many electrical and mechanical parts in this chassis have special safety-related characteristics. These parts are identified by the Schematic Diagram and Replacement Parts List. It is essential that these special safety parts should be replaced with the same components as recommended in this manual to prevent X-RADIATION, Shock, Fire, or other Hazards.
SERVICING PRECAUTIONS CAUTION: Before servicing receivers covered by this service transistors and semicounductor "chip" components. The manual and its supplements and addenda, read and follow the following techniques should be used to help reduce the SAFETY PRECAUTIONS on page 3 of this publication. incidence of component damage caused by static by static NOTE: If unforeseen circumstances create conflict between the electricity.
Page 5
c. Qulckly move the soldering iron tip to the junction of the Fuse and Conventional Resistor component lead and the printed circuit foil, and hold it Removal/Replacement there only until the solder flows onto and around both the 1. Clip each fuse or resistor lead at top of the circuit board component lead and the foil.
SPECIFICATIONS NOTE : Specifications and others are subject to change without notice for improvement. Video input system: Power consumption : Multi 26 System 250 Wmax. (Refer to Table 1) Intermediate Frequency Tuning system : Vision IF : 38.9MHz FVS 100 Program Memory(With Teletext Model) Color IF : 34.47MHz *SECAM : 38.9-4.25MHz FVS 200 Program Memory(W/O Teletext Model)
Page 7
T able 1 : Receiving System (26 System) Receiving System Receiving Channel Function P P A A L L - - B B P P A A L L - - G G V V H H F F B B a a n n d d P P A A L L - - I I : : 2 2 - - 1 1 2 2 PAL/SECAM-B...
CONTROLS DESCRIPTION All the functions can be controlled with the remote control handset. Some functions can also be adjusted with the buttons on the front panel of the set. Remote control handset Before you use the remote control handset, please install the bat- teries.
Page 9
11. LIST displays the programme table. 12. VCR BUTTONS control a LG video cassette recorder. 13. EYE switches the eye function on or off. 14. TV/AV selects TV or AV mode. POWER clears the menu / text from the screen.
Location and function of controls Front panel • PT-48/53A82 series DIGITAL INDEX PRO LOGIC LOGIC MOVIE SPOR MOVIE SPORTS MUSIC TS MUSIC MENU PRO LOGIC LOGIC DIGITAL INDEX MOVIE SPOR MOVIE SPORTS MUSIC TS MUSIC MENU CATV CATV TV/AV TV/AV ON/OFF ON/OFF •...
) to reset the convergence. 1. Test Equipment Signal Generator can produce DOT pattern 2. Adjustment LG Convergence assy 2. Preliminary steps Make green raster using lens cover and coincide 1) Heat run over 60 minutes. horizontal/vertical center lines of pattern with those of 2) Pre-adjust Raster slope,Raster position &...
High Voltage Regulation Adjustment 4) HS (Horizontal Shift) Adjust so that the horizontal center line of a digital circle pattern is in accord with geometric horizontal center of the CPT. 1. Test Equipment Digital Multi-Meter(DMM) 5) EW (East-west Width) Adjust until the outermost left and right vertical line of the 2.
Lens Focus & Electronic Focus Adjustment to green which of 3.5 Cross-Hatch part from picture's center toward left. 1. Preliminary steps 1) Electronic focus,Raster slope & Raster position must be pre- adjusted. 2) Heat-run over 60 minutes. 3) Receive Crosshatch pattern. 4) Adjustment must be operated in a dark room(simple dark 2) Adjust the chromatic aberration become center of purple and room) and pay attention not to touch the lens during...
3. Pattern Position Adjustment X=0.280 and Y=0.300 (Deviation : ! 0.01). 6) Set BRIGHT to L/Light adjustment mode and adjust CR (R 1) Change into pattern shift mode. Cut Off) and CB (B Cut Off) until color coordinate becomes (Press numeric buttons “9” & “4”) X=0.282 and Y=0.286 (Deviation : ! 0.01).
Page 15
SVC Adjustment mode & Initial data Range Menu Description Default DC-TR DC transmission control 1. White Blalane adjustment data (IC:CXA2100) LRGB2 RGB2 output level control Menu Description Range Default DL-PA DElay Line switching Red Drive SHPF0 Sharpness f0 Green Drive CB-F1 INput1 CB signal DC Offset Blue Drive...
Page 16
6.OPTION Data Adjustment Range Description Default Range Description Default 1: With Teletext 200 PRO 1: 200 Program(CHINA Only) TEXT 0: Without Teletext(CHINA) 0: 100 Program 1: RF 54% Modulation INput TSEAR 1: With TURBO Search option3 SCART 0: RF 100% Modulation INput 0: Without TURBO Search 1: China+AUST.Channel Table I/II SV...
Page 17
State Language Funciton Default 0:E Only English 1:EU 5EA English/German/French/Italy/Spanish 2:EU ETC Pol./Hungary/Czecho/Russia/Eng 3:PARSI English/Parsi LANG 4:ARAB DUAL English/French/Arab+Urdu 5:English+Hindi English/Hindi 6:English+I+M+V English/Indonesian/Malaysian/Vietnamese 7:English+THAI English/Thai 8:English+China English/China 0:West Europe English/French/Swedish/Czech/German/Spanish/Itallian 1:East Europe Polish/Fench/Swedish/Czech/German/Slovenian/Italian/Romanian option4 2:Turkey English/French/Swedish/Turkish/German/Spanish/Itallian 3:EAST EU2 English/Hungarian/Serbian/Czech/German/Polish/Spanish/Itallian/ Romanian 4:Cyrillic 1 5:Cyrillic 2 6:Cyrillic 3...
Trouble Shooting 1. NO PICTURE ( SOUND OK ) CVBS Signal ? Check MAIN1 Q101(E) Waveform. (2Vpp) Check around Waveform of AV Board IC202 #63 ? Check Tuner(TU101) VIDEO output IC202 Waveform of AV Board Q505(E) ? Check around IC202 Waveform of VIDEO Board Check IC501 IC501 #72 ?
Page 19
2. NO SOUND (PICTURE OK) <AV1,2,3,DVD(480i),DVD(480p) INPUT> < RF > Waveform of Waveform of AV Board IC205 Check arround Check MAIN1 Q103 #47,48,50,51,53,54,56,57 each Jack TU101 Q104 ( SIF ) ? at each Mode ? Waveform of Check AV Board IC205 around #67 ? IC205...
Page 20
3. NO PIP <AV1,2,3> <RF> <SCART> Waveform of PIP Waveform of AV Board Waveform of MAIN1 Board IC502 IC202 #8,15,22,35 ? Q110(E) ? #1,2,3,7,9 ? Check JA202 Waveform of Video Board Check Video Board IC202 #44 ? Q203,IC202 Check Scart Jack JA204 Waveform of Video Board Check P212B...
Page 21
4. NO Teletext (Picture OK) Waveform of MAIN1 IC501 #4 ? Check Micom IC001 Micom Board Ic001 #21 ? #57~60 Check OPTION3 TEXT Code (SVC MODE) 5. NO OSD (ON SCREEN DISPLAY) Horizontal, Vertical Fly Back Input Waveform of Micom Board IC001 #29,#30 ? Check DEF.
Page 22
6. NO POWER ON Check input voltage of Check SMPS Board IC001#6,8,22,40,56,73,75,92 Check IC001 #52,53 Replace X001 (OSC) Replace Q003, Q004 Check IC001 #11,12 (SCL,SDA) Check Abnormnal Circuit Check IC001 #44 (ABN) HIGH Check IC001 #34 ( IR ), Check P004A connector #31~38 (Key In) - 22 -...
Page 24
8.NO RASTER Check +B voltage 115V or not Is the voltage Open Check F801 at Pin 76,69 of IC501 5V ? Check 5V,9V, Check / Replace 12V lines F801,D815 IC801 Does the square waveform from Pin 17 Check the voltage of IC702 appear? of C812(+) Check IIC bus lines...
Page 25
9. INCORRECT CONVERGENCE Does the static convergence correct? Check the input vlotage Re-adjust static convergence at P201 by remote controller Not controlled Controlled Are there pulse signal Check pulse pin125 Check voltage on the at pin121 of IC2051 of IC2051(4Mhz) SMPS PCB Are there V,H pulse Check / Replace...
Page 47
EXPLODED VIEW PARTS LIST The components identified by mark critical for safety. Replace only with part number specified. Part No. Description 3680V00007A LENS,SEKINOS SSM-75(50) . . 4810V00395F BRACKET,BLUE LENS+COUPLER+CPT S/S 4810V00395E BRACKET,GREEN LENS+COUPLER+CPT S/S 4810V00395D BRACKET,RED LENS+COUPLER+CPT S/S 120-D38E SPEAKER,MID-RANGE 8 OHM 15/25W 87DB 6401VD0006G SPEAKER,FULLRANGE(L)WOOFER+TWEETER 6401VD0006H...
Page 49
EXPLODED VIEW PARTS LIST The components identified by mark critical for safety. Replace only with part number specified. Part No. Description 3680V00007A LENS,SEKINOS SSM-75(50) 4810V00395F BRACKET,BLUE LENS+COUPLER+CPT S/S 4810V00395E BRACKET,GREEN LENS+COUPLER+CPT S/S 4810V00395D BRACKET,RED LENS+COUPLER+CPT S/S 120-D38E SPEAKER,MID-RANGE 8 OHM 15/25W 87DB 12 6401VD0006G SPEAKER,FULLRANGE (L)WOOFER+TWEETER 6401VD0006H...
REPLACEMENT PARTS LIST LOCA. NO PART NO DESCRIPTION LOCA. NO PART NO DESCRIPTION IC871 0ISK115000A IC,SE115N(LF12) 3P 115V ERROR AMP IC887 0ILI817000G IC,LTV817M-VB 4P,DIP BK PHOTO COU IC001 0IAL241610B IC,AT24C16-10PC-2.7 8PIN DIP ST E IC,LTV817M-VB 4P,DIP BK PHOTO COU IC891 0ILI817000G IC001 0ISM555000A...
Page 51
LOCA. NO PART NO DESCRIPTION LOCA. NO PART NO DESCRIPTION D434 0DS113379BA DIODE,SWITCHING 1SS133 T-72 D907 0DD226239AA DIODE,SWITCHING KDS226 SOT-23 D435 0DS113379BA DIODE,SWITCHING 1SS133 T-72 D908 0DD226239AA DIODE,SWITCHING KDS226 SOT-23 DIODE,SWITCHING 1SS133 T-72 DIODE,SWITCHING KDS226 SOT-23 D437 0DS113379BA D910 0DD226239AA D600 0DS113379BA DIODE,SWITCHING 1SS133 T-72...
Page 52
LOCA. NO PART NO DESCRIPTION LOCA. NO PART NO DESCRIPTION ZD902G 0DZ110009AD DIODE,ZENER MTZJ11B TP ROHM-K DO34 - 11V Q203 0TR387500AA TR,CHIP 2SC3875S(ALY) KEC ZD902R 0DZ110009AD DIODE,ZENER MTZJ11B TP ROHM-K DO34 - 11V Q204 0TR387500AA TR,CHIP 2SC3875S(ALY) KEC TR,CHIP 2SC3875S(ALY) KEC ZD1001 0DZ620009BB DIODE,ZENER MTZJ6.2B TP ROHM-K DO34 0.5W...
Page 53
For Capacitor & Resistors, the CC, CX, CK, CN : Ceramic RD : Carbon Film charactors at 2nd and 3rd digit CQ : Polyestor RS : Metal Oxide Film in the P/No. means as follows; CE : Electrolytic RN : Metal Film RF : Fusible LOCA.
Page 54
For Capacitor & Resistors, the CC, CX, CK, CN : Ceramic RD : Carbon Film charactors at 2nd and 3rd digit CQ : Polyestor RS : Metal Oxide Film in the P/No. means as follows; CE : Electrolytic RN : Metal Film RF : Fusible LOCA.
Page 55
For Capacitor & Resistors, the CC, CX, CK, CN : Ceramic RD : Carbon Film charactors at 2nd and 3rd digit CQ : Polyestor RS : Metal Oxide Film in the P/No. means as follows; CE : Electrolytic RN : Metal Film RF : Fusible LOCA.
Page 56
For Capacitor & Resistors, the CC, CX, CK, CN : Ceramic RD : Carbon Film charactors at 2nd and 3rd digit CQ : Polyestor RS : Metal Oxide Film in the P/No. means as follows; CE : Electrolytic RN : Metal Film RF : Fusible LOCA.
Page 57
For Capacitor & Resistors, the CC, CX, CK, CN : Ceramic RD : Carbon Film charactors at 2nd and 3rd digit CQ : Polyestor RS : Metal Oxide Film in the P/No. means as follows; CE : Electrolytic RN : Metal Film RF : Fusible LOCA.
Page 58
For Capacitor & Resistors, the CC, CX, CK, CN : Ceramic RD : Carbon Film charactors at 2nd and 3rd digit CQ : Polyestor RS : Metal Oxide Film in the P/No. means as follows; CE : Electrolytic RN : Metal Film RF : Fusible LOCA.
Page 60
For Capacitor & Resistors, the CC, CX, CK, CN : Ceramic RD : Carbon Film charactors at 2nd and 3rd digit CQ : Polyestor RS : Metal Oxide Film in the P/No. means as follows; CE : Electrolytic RN : Metal Film RF : Fusible LOCA.
Page 61
For Capacitor & Resistors, the CC, CX, CK, CN : Ceramic RD : Carbon Film charactors at 2nd and 3rd digit CQ : Polyestor RS : Metal Oxide Film in the P/No. means as follows; CE : Electrolytic RN : Metal Film RF : Fusible LOCA.
Page 62
For Capacitor & Resistors, the CC, CX, CK, CN : Ceramic RD : Carbon Film charactors at 2nd and 3rd digit CQ : Polyestor RS : Metal Oxide Film in the P/No. means as follows; CE : Electrolytic RN : Metal Film RF : Fusible LOCA.
Page 63
For Capacitor & Resistors, the CC, CX, CK, CN : Ceramic RD : Carbon Film charactors at 2nd and 3rd digit CQ : Polyestor RS : Metal Oxide Film in the P/No. means as follows; CE : Electrolytic RN : Metal Film RF : Fusible LOCA.
Page 64
For Capacitor & Resistors, the CC, CX, CK, CN : Ceramic RD : Carbon Film charactors at 2nd and 3rd digit CQ : Polyestor RS : Metal Oxide Film in the P/No. means as follows; CE : Electrolytic RN : Metal Film RF : Fusible LOCA.