Table of Contents
Advertisement
2-7: VERTICAL POSITION
1.
Receive the monoscope pattern.
2.
Using the remote control, set the brightness and contrast
to normal position.
3.
Adjust the VR401 until the horizontal line becomes fit to
the notch of the shadow mask.
2-8: VERTICAL SIZE
1.
Receive the monoscope pattern.
2.
Using the remote control, set the brightness and contrast
to normal position.
3.
Activate the adjustment mode display of Fig. 1-1 and
press the channel button (07) on the remote control to
select "V. SIZE".
4.
Press the VOL. UP/DOWN button on the remote control
until the SHIFT quantity of the OVER SCAN on upside
and downside becomes 9 ± 2%.
2-9: VERTICAL LINEARITY
NOTE: Adjust after performing adjustments in section 2-8.
After the adjustment of Vertical Linearity, reconfirm
the Vertical Position and Vertical Size adjustments.
1.
Receive the monoscope pattern.
2.
Using the remote control, set the brightness and contrast
to normal position.
3.
Activate the adjustment mode display of Fig. 1-1 and
press the channel button (09) on the remote control to
select "V. LIN".
4.
Press the VOL. UP/DOWN button on the remote control
until the SHIFT quantity of the OVER SCAN on upside
and downside becomes minimum.
2-10: BRIGHT CENT
1.
Receive the monoscope pattern. (RF Input)
2.
Using the remote control, set the brightness and
contrast to normal position.
3.
Activate the adjustment mode display of Fig. 1-1 and
press the channel button (16) on the remote control to
select "BRI CENT".
4.
Press the VOL. UP/DOWN button on the remote
control until the white 10% is starting to be visible
5.
Receive the monoscope pattern. (Audio Video Input)
6.
Press the TV/VIDEO button on the remote control to
set to the AV mode. Then perform the above
adjustments 2~4.
7.
Press the TV/VIDEO button on the remote control to
set to the CS mode.
8.
Activate the adjustment mode display of Fig. 1-1 and
press the channel button (16) on the remote control to
select "BRI CENT".
9.
Press the VOL. UP/DOWN button on the remote
control until the brightness step No. becomes "84".
ELECTRICAL ADJUSTMENTS
2-11: SUB TINT/COLOR CENT
1.
Receive the color bar pattern. (RF Input)
2.
Connect the oscilloscope to TP806.
3.
Using the remote control, set the brightness, contrast,
color and tint to normal position.
4.
Activate the adjustment mode display of Fig. 1-1 and
press the channel button (26) on the remote control to
select "TINT".
5.
Press the VOL. UP/DOWN button on the remote control
until the section "A" becomes a straight line
(Refer to Fig. 2-1).
6.
Connect the oscilloscope to TP804.
7.
Press the channel button (24) on the remote control to
select "COL. CENT".
8.
Adjust the VOLTS RANGE VARIABLE knob of the
oscilloscope until the range between white 100% and
0% is set to 5 scales on the screen of the oscilloscope.
9.
Press the VOL. UP/DOWN button on the remote control
until the red color level is adjusted to 110 ± 5% of the
white level. (Refer to Fig. 2-2)
10.
Receive the color bar pattern. (Audio Video Input)
11.
Press the TV/VIDEO button on the remote control to set
to the AV mode. Then perform the above adjustments
2~9.
12.
Press the TV/VIDEO button on the remote control to set
to the CS mode.
13.
Activate the adjustment mode display of Fig. 1-1 and
press the channel button (26) on the remote control to
select "TINT".
14
Press the VOL. UP/DOWN button on the remote control
until the tint step No. becomes "52".
15.
Press the channel button (24) on the remote control to
select "COL. CENT".
16.
Press the VOL. UP/DOWN button on the remote control
until the color step No. becomes "53".
White 100%
Fig. 2-1
RED Level
Fig. 2-2
Advertisement
Table of Contents
