Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for HAI OmniTouch 10p
Summary of Contents for HAI OmniTouch 10p
- Page 1 10” Portable Color Touchscreen User’s Manual...
- Page 2 Trademarks Microsoft and Windows are either registered trademarks or trademarks of Microsoft Corporation. Other product names mentioned in this manual may be trademarks or registered trademarks of their respective companies and are hereby acknowledged. Document Number: 67I00-1 Rev. A 2009 Home Automation, Inc.
-
Page 3: Regulatory Compliance Statements
Regulatory Compliance Statements FCC Statement FCC Caution: To assure continued compliance, any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. (Example - use only shielded interface cables when connecting to computer or peripheral devices). FCC Radiation Exposure Statement This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. -
Page 4: Canada-Industry Canada (Ic)
• and/or humidity ranges, condensation may form on or within the OmniTouch 10p. To avoid damaging the OmniTouch 10p, allow sufficient time for the moisture to evaporate before using the OmniTouch 10p. When you disconnect a cable, pull on its connector or on its strain relief loop, not on the cable •... -
Page 5: Rtc Battery/Battery Safety
CAUTION! The battery used in this device may present a risk of fire or chemical burn if mistreated. Do no disassemble, heat above 60 degree C, or incinerate. Replace battery with HAI P/N: 67A03-1 (46-12427-041) only. Use of another battery may present a risk of fire or explosion. -
Page 6: Table Of Contents
Charging the Battery with the Optional Docking Station ..................11 Power LED Status .........................13 Checking the Battery Status ............................. 13 Turning On the OmniTouch 10p for the First Time ..............13 Powering On ................................14 Calibrating the OmniTouch 10p Screen ........................15 Configuring the Wireless Network.......................... - Page 7 Using the Hardware ..............23 Using the Stylus ..........................24 Inserting an SD Memory Card ......................25 Removing a Storage Card ............................25 Connecting Devices to the OmniTouch 10p ................26 Opening the Port Covers ............................26 Connecting USB ................................. 26 Connecting a Serial Device ............................27 Note: Use a female DB-9 cable when connecting to this port.Connecting an External Monitor .......
-
Page 9: Introducing The Omnitouch 10P
A software keyboard included enables you to enter and edit text. The OmniTouch 10p is sealed to meet IP53 standards and has undergone multiple 70cm drop tests. -
Page 10: Package Contents
Package Contents After opening the box, ensure the following accessories for the OmniTouch 10p are present: OmniTouch 10p AC adapter and power cord Stylus Battery... -
Page 11: Omnitouch 10P Overview
OmniTouch 10p Overview The following sections describe the main components of the OmniTouch 10p. Front View... -
Page 12: Front View Description
Solid orange: power is on and battery is low (10%-30%). • Blinking orange: power is on and battery is very low (less • than 10%). The OmniTouch 10p will auto-suspend when the battery reaches 3% battery charge. Microphone Enables you to speak into the OmniTouch 10p (for future use). -
Page 13: Left And Right View
Left and Right View Top View... -
Page 14: Left, Right, And Top View Description
VGA port This port connects to an external monitor Headphone jack This jack connects to audio line-level devices (e.g. headphones). This jack enables you to speak into the OmniTouch 10p with an Microphone jack external microphone (for future use). Docking/Cradle... -
Page 15: Back View
Back View Back View Description Component Description Speakers Enables you to hear audio from the OmniTouch 10p. This stand can be used to erect and adjust the viewing angle of the Stand OmniTouch 10p on a sturdy and level surface. Battery... -
Page 16: About The Optional Docking Cradle
About the Optional Docking Cradle The optional 67A01-1 OmniTouch 10p Docking Cradle is used to secure the OmniTouch 10p in an upright position, while providing power to the unit, charging the battery, and connecting to connected USB devices. When the optional 67A01-1 Docking Cradle is used, the OmniTouch 10p Touchscreen should be placed in the cradle while it’s not in use. -
Page 17: Getting Started
CAUTION! The battery used in this device may present a risk of fire or chemical burn if mistreated. Do no disassemble, heat above 60°C, or incinerate. Replace battery with HAI P/N: 67A03-1 (46-12427-041) only. Use of another battery may present a risk of fire or explosion. - Page 18 3. Pull up at the lip of the battery compartment cover and remove the cover. 4. Align the battery pack, making sure the battery contacts are aligned with the contacts in the compartment and place the battery in the compartment as shown in the following illustration. 5.
-
Page 19: Charging The Battery
Charging the Battery Before using the OmniTouch 10p for the first time, you need to charge it for about 2 hours. Charge the OmniTouch 10p using the AC adapter or the optional Docking Cradle. Charging the Battery Using the AC Adapter 1. - Page 20 Slide the device into the Docking Cradle until it snaps into place. The connection is secure when the bottom edge of the OmniTouch 10p is aligned with the docking station and the LED indicator on the device lights up green.
-
Page 21: Power Led Status
Turning On the OmniTouch 10p for the First Time After you have initially charged the OmniTouch 10p for about 2 hours, it is ready to be used. When you turn on the OmniTouch 10p for the first time, you should calibrate the display, setup the wireless network, and set up the system time zone, date, and time before connecting to the HAI controller. -
Page 22: Powering On
Powering On 1. Turn on the OmniTouch 10p by sliding the power button on the top of the unit. 2. When the OmniTouch 10p starts up for the first time, the OmniTouch 10p configuration screen will be displayed: 3. Press the [Exit] button to exit the application so that you can calibrate the display, setup the wireless network, and set up the system time zone, date, and time before connecting to the HAI controller. -
Page 23: Calibrating The Omnitouch 10P Screen
Calibrating the OmniTouch 10p Screen The PenMount Control Panel is used to calibrate the OmniTouch 10p screen as follows: 1. Using the stylus, tap the PenMount Control Panel icon in the system tray. 2. Tap Control Panel to open the PenMount Control Panel. -
Page 24: Configuring The Wireless Network
6. Touch and hold the red squares and follow the instructions on the screen to calibrate the stylus. Configuring the Wireless Network The embedded wireless network module in the OmniTouch 10p allows you to connect to the HAI controller and to the Internet over a wireless network. - Page 25 3. When connecting to a secure network, you are prompted to enter a network key. 4. Enter the required network key and reenter the key for confirmation and then tap “Connect”. 5. The wireless connection is negotiated. Once connected, you will see the following: The Wireless Network Connection icon in the system tray indicates that a wireless connection is active.
-
Page 26: Setting The Time And Date
Setting the Time and Date Follow these instructions to set the time and date. 1. Double-tap the time in the system tray. 2. Tap the arrow next to the month to select the correct month. 3. Tap the arrows next to the year to select the correct year. 4. -
Page 27: Connecting To The Hai Controller
Connecting to the HAI Controller Once the wireless network has been configured, you can then enter the HAI controller connection information to connect to the controller. To enter the controller connection information, double-tap the OmniTouchPro_10P icon, as shown. When the application starts up, the OmniTouch 10p configuration screen will be displayed:... - Page 28 1. Enter the IP address of the HAI Controller by pressing the [Edit] button to the right of the “Controller” Edit Box: The controller’s local network IP address is used to identify the HAI controller on the network. The format of the IP address is a numeric address written as four numbers separated by periods.
- Page 29 5. If an HAI controller is not being used, press the [Off] button under “Controller”. This can be used if you are using an OmniTouch 10p to communicate with an HTX Home Theater Extender, but are not connecting to or do not have an HAI controller.
-
Page 30: Starting The Omnitouchpro Application
Starting the OmniTouchPro Application Once the correct HAI controller information has been entered and the connection to the controller has been established, the OmniTouchPro page is displayed. Returning to the Configuration Page To return to the configuration page, press on any blank space on any page within the OmniTouchPro... -
Page 31: Using The Hardware
Chapter 3 Using the Hardware Using the Stand The OmniTouch 10p has a built-in stand for easy configuration on a desk or table top. Open the stand and adjust the tilt to provide the best viewing angle. -
Page 32: Using The Stylus
Using the Stylus Use the stylus to interact with the OmniTouch 10p by tapping or double-tapping on an application icon and to select items on the menu. When not in use, place the stylus in the storage slot located on the top of the OmniTouch 10p. -
Page 33: Inserting An Sd Memory Card
Inserting an SD Memory Card Your OmniTouch 10p has an expansion slot compatible with a range of SD cards, which are primarily used to back up or transfer files and data. The slot also supports SDIO cards for added connectivity options. -
Page 34: Connecting Devices To The Omnitouch 10P
Ensure that you close the covers tightly after disconnecting cables and connectors. Connecting USB The following illustration shows how to connect a USB Type A device to the OmniTouch 10p. The connector can only go in one way. If it does not go in smoothly, check the orientation and try again. -
Page 35: Connecting A Serial Device
Connecting a Serial Device Connect a serial device to the OmniTouch 10p to perform serial communications. Note: Use a female DB-9 cable when connecting to this port. -
Page 36: Connecting An External Monitor
Connecting an External Monitor Connect an external monitor cable to the VGA port on the OmniTouch 10p to view the output on an external monitor. -
Page 37: Connecting Lan
Connecting LAN Connect an RJ-45 cable to the Ethernet port on the OmniTouch 10p to enable you to connect to a wired local network (LAN). Connecting Headphones and a Microphone The OmniTouch 10p has an external jack microphone and speaker. -
Page 38: Connecting To An Optional Cradle
USB devices. Connecting Power Connect the AC adapter to the optional cradle to power the OmniTouch 10p and to charge the battery. Connecting USB You can connect peripheral devices, such as a USB keyboard and USB mouse, as well as other USB... -
Page 39: System Specifications
Appendix A System Specifications Component OmniTouch 10p Operating System Windows XP Embedded AMD GeodeTM LX800 500MHz Processor AMD GeodeTM CS5536 Companion Chip Memory DDR400 SODIMM 512MB Display SVGA Model: 10.4-inch TFT LCD (800 x 600) Touch Panel Transtouch 4-wire resistive touch panel... - Page 40 Component OmniTouch 10p 1 RS-232 port 2 USB type A connectors 1 RJ45 for 10/100Mbps Ethernet port One SD slot External I/O 1 stereo headphone jack One microphone jack Interfaces 1 VGA output 1 DC-in jack 1 Docking connector for cradle...
-
Page 41: Maintenance
Cleaning the LCD display should only be done with a soft cloth dampened LCD screen • cleaner solution. Cleaning the OmniTouch 10p Turn off the OmniTouch 10p and unplug the power cord. • Wipe the screen and the exterior with a soft, damp cloth moistened only with water. •...
Need help?
Do you have a question about the OmniTouch 10p and is the answer not in the manual?
Questions and answers