Page 1 2006 GMC Sierra Denali Owner Manual Seats and Restraint Systems ......1-1 Driving Your Vehicle ........4-1 Front Seats ..........1-2 Your Driving, the Road, and Your Vehicle ..4-2 Rear Seats ..........1-6 Towing ........... 4-49 Safety Belts ..........1-8 Service and Appearance Care ......
Page 2: How To Use This Manual
Detroit, MI 48207 GENERAL MOTORS, GM, the GM Emblem, GMC, How to Use This Manual the GMC Truck Emblem, and the names SIERRA and DENALI are registered trademarks of General Motors Many people read the owner manual from beginning to Corporation.
Page 3 Safety Warnings and Symbols You will also ﬁnd a circle with a slash through it in this book. This safety There are a number of safety cautions in this book. We symbol means “Do Not,” use a box and the word CAUTION to tell about things “Do Not do this”...
Page 4: Vehicle Symbols
Vehicle Damage Warnings Vehicle Symbols Also, in this manual you will ﬁnd these notices: The vehicle has components and labels that use symbols instead of text. Symbols are shown along with Notice: These mean there is something that could the text describing the operation or information relating damage your vehicle.
Page 5 These are some examples of symbols that may be found on the vehicle:...
Page 6 NOTES...
Page 7: Table Of Contents
Section 1 Seats and Restraint Systems Front Seats ............1-2 Where to Put the Restraint ......1-36 Power Seats ..........1-2 Lower Anchors and Tethers for Power Lumbar ..........1-3 Children (LATCH) ........1-38 Heated Seats ..........1-3 Securing a Child Restraint in a Reclining Seatbacks ........1-4 Rear Seat Position ........1-44 Head Restraints ..........1-6 Securing a Child Restraint in the...
Page 8: Front Seats
Front Seats Horizontal Control: You can adjust your vehicle’s front seats with the horizontal control located on the outboard edge of each front seat. Power Seats Raise or lower the front of the seat by raising or lowering the forward edge of the control. Raise or lower the rear of the seat by raising or lowering the rear edge of the control.
Page 9: Power Lumbar
Power Lumbar Your vehicle may have a memory function which allows seat settings to be saved and recalled. See Memory Seat on page 2-44 for more information. Your vehicle’s seats may be equipped with power lumbar. Heated Seats You can increase or decrease lumbar support If your vehicle has this in an area of the lower...
Page 10: Reclining Seatbacks
Reclining Seatbacks To heat only the seatback, press the vertical button with the heated seatback symbol. An indicator light on the seatback button will be lit to designate that only The front seats have a power recline feature. the seatback is being heated. Additional presses of the seatback button will cycle through the heat levels for the seatback only.
Page 11 CAUTION: Sitting in a reclined position when your vehicle is in motion can be dangerous. Even if you buckle up, your safety belts cannot do their job when you are reclined like this. The shoulder belt cannot do its job. In a crash, you could go into it, receiving neck or other injuries.
Page 12: Rear Seats
Head Restraints Each front head restraint can also be tilted forward to four positions by pulling on it. A click will sound after each tilt position is reached. Pull the head restraint forward, past the last position, to release it to the upright position. The rear seat head restraints are also adjustable up and down, but they do not tilt.
Page 13 To ﬂip and fold the seat, do the following: To return the seat to the normal seating position, do the following: 1. Pull up on the strap 1. Lift the seatback up and push it rearward all loop at the rear of the the way.
Page 14 Safety Belts 3. Lower the seat cushion until it latches into position. Pull up on the seat cushion to make sure it is locked into place. Safety Belts: They Are for Everyone CAUTION: This part of the manual tells you how to use safety belts properly.
Page 15 Your vehicle has a light that comes on as a CAUTION: reminder to buckle up. See Safety Belt Reminder Light on page 3-30. It is extremely dangerous to ride in a cargo area, inside or outside of a vehicle. In a collision, people riding in these areas are more likely to be seriously injured or killed.
Page 16: Why Safety Belts Work
Why Safety Belts Work When you ride in or on anything, you go as fast as it goes. Put someone on it. Take the simplest vehicle. Suppose it is just a seat on wheels. 1-10...
Page 17 Get it up to speed. Then stop the vehicle. The rider The person keeps going until stopped by something. does not stop. In a real vehicle, it could be the windshield... 1-11...
Page 18 or the instrument panel... or the safety belts! With safety belts, you slow down as the vehicle does. You get more time to stop. You stop over more distance, and your strongest bones take the forces. That is why safety belts make such good sense. 1-12...
Page 19 Questions and Answers About If I am a good driver, and I never drive far from home, why should I wear safety belts? Safety Belts You may be an excellent driver, but if you are in an accident — even one that is not your fault — you Will I be trapped in the vehicle after an accident and your passengers can be hurt.
Page 20 How to Wear Safety Belts Properly This part is only for people of adult size. Be aware that there are special things to know about safety belts and children. And there are different rules for smaller children and babies. If a child will be riding in your vehicle, see Older Children on page 1-27 or Infants and Young Children on page 1-30.
Page 21 5. To make the lap part tight, pull up on the shoulder belt. The lap part of the belt should be worn low and snug on the hips, just touching the thighs. In a crash, this applies force to the strong pelvic bones. And you would be less likely to slide under the lap belt.
Page 22 What is wrong with this? CAUTION: You can be seriously hurt if your shoulder belt is too loose. In a crash, you would move forward too much, which could increase injury. The shoulder belt should ﬁt against your body. The shoulder belt is too loose. It will not give nearly as much protection this way.
Page 23 What is wrong with this? CAUTION: You can be seriously injured if your belt is buckled in the wrong place like this. In a crash, the belt would go up over your abdomen. The belt forces would be there, not at the pelvic bones.
Page 24 What is wrong with this? CAUTION: You can be seriously injured if your belt goes over an armrest like this. The belt would be much too high. In a crash, you can slide under the belt. The belt force would then be applied at the abdomen, not at the pelvic bones, and that could cause serious or fatal injuries.
Page 25 What is wrong with this? CAUTION: You can be seriously injured if you wear the shoulder belt under your arm. In a crash, your body would move too far forward, which would increase the chance of head and neck injury. Also, the belt would apply too much force to the ribs, which are not as strong as shoulder bones.
Page 26 What is wrong with this? CAUTION: You can be seriously injured by a twisted belt. In a crash, you would not have the full width of the belt to spread impact forces. If a belt is twisted, make it straight so it can work properly, or ask your dealer to ﬁx it.
Page 27 Safety Belt Use During Pregnancy Safety belts work for everyone, including pregnant women. Like all occupants, they are more likely to be seriously injured if they do not wear safety belts. To unlatch the belt, just push the button on the buckle. The belt should go back out of the way.
Page 28 Right Front Passenger Position Lap-Shoulder Belt All rear seat positions have lap-shoulder belts. Here is To learn how to wear the right front passenger’s safety how to wear one properly. belt properly, see Driver Position on page 1-14. The right front passenger’s safety belt works the same way as the driver’s safety belt —...
Page 29 2. Push the latch plate into the buckle until it clicks. Pull up on the latch plate to make sure it is secure. When the shoulder belt is pulled out all the way, it will lock. If it does, let it go back all the way and start again.
Page 30 The safety belt locks if there is a sudden stop or a crash, or if you pull the belt very quickly out of the retractor. CAUTION: You can be seriously hurt if your shoulder belt is too loose. In a crash, you would move forward too much, which could increase injury.
Page 31 There is one guide for each outside passenger in the rear seat. Here is how to install a comfort guide and use the safety belt: 1. Remove the guide from its storage clip on the interior body. To unlatch the belt, push the button on the buckle. Rear Safety Belt Comfort Guides Rear seat comfort guides may provide added safety belt comfort for older children who have outgrown booster...
Page 32 3. Be sure that the belt is not twisted and it lies ﬂat. The guide must be on top of the belt. CAUTION: A safety belt that is not properly worn may not provide the protection needed in a crash. The person wearing the belt could be seriously injured.
Page 33 Child Restraints 4. Buckle, position, and release the safety belt as described in Rear Seat Passengers on page 1-22. Make sure that the shoulder belt crosses the Older Children shoulder. To remove and store the comfort guides, squeeze the belt edges together so that you can take them out of the guides.
Page 34: Safety Belts
What is the proper way to wear safety belts? An older child should wear a lap-shoulder belt and get the additional restraint a shoulder belt can provide. The shoulder belt should not cross the face or neck. The lap belt should ﬁt snugly below the hips, just touching the top of the thighs.
Page 35 What if a child is wearing a lap-shoulder belt, but the child is so small that the shoulder belt CAUTION: is very close to the child’s face or neck? If the child is sitting in a seat next to a window, Never do this.
Page 36: Infants And Young Children
Infants and Young Children Everyone in a vehicle needs protection! This includes infants and all other children. Neither the distance traveled nor the age and size of the traveler changes the need, for everyone, to use safety restraints. In fact, the law in every state in the United States and in every Canadian province says children up to some age must be restrained while in a vehicle.
Page 37 What are the different types of add-on child restraints? Add-on child restraints, which are purchased by the vehicle’s owner, are available in four basic types. Selection of a particular restraint should take into consideration not only the child’s weight, height and age but also whether or not the restraint will be compatible with the motor vehicle in which it will be used.
Page 38 The restraint manufacturer’s instructions that come with the restraint, state the weight and height CAUTION: limitations for a particular child restraint. In addition, there are many kinds of restraints available for children with special needs. The body structure of a young child is quite unlike that of an adult or older child, for whom the safety belts are designed.
Page 39: Child Restraint Systems
Child Restraint Systems A rear-facing infant seat (B) provides restraint with the seating surface against the back of the infant. The harness system holds the infant in place and, An infant car bed (A), a special bed made for use in a in a crash, acts to keep the infant positioned in motor vehicle, is an infant restraint system designed the restraint.
Page 40 A forward-facing child seat (C-E) provides restraint for A booster seat (F-G) is a child restraint designed to the child’s body with the harness and also sometimes improve the ﬁt of the vehicle’s safety belt system. with surfaces such as T-shaped or shelf-like shields. Some booster seats have a shoulder belt positioner, and some high-back booster seats have a ﬁve-point harness.
Page 41 Securing an Add-on Child Restraint in How Should I Use a Child Restraint? the Vehicle A child restraint system is any device designed for use in a motor vehicle to restrain, seat, or position children. A built-in child restraint system is a CAUTION: permanent part of the motor vehicle.
Page 42 When securing an add-on child restraint, refer to the instructions that come with the restraint which may be on CAUTION: the restraint itself or in a booklet, or both, and to this manual. The child restraint instructions are important, so if they are not available, obtain a replacement copy A child can be seriously injured or killed in a from the manufacturer.
Page 43 Your vehicle has a rear seat that will accommodate a rear-facing child restraint. A label on your sun visor says, CAUTION: (Continued) “Never put a rear-facing child seat in the front.” This is because the risk to the rear-facing child is so great, Even though the passenger sensing system is if the airbag deploys.
Page 44: Lower Anchors And Tethers For Children (Latch)
Lower Anchors and Tethers for In order to use the LATCH system in your vehicle, you need a child restraint equipped with LATCH Children (LATCH) attachments. The child restraint manufacturer will provide you with instructions on how to use the child Your vehicle has the LATCH system.
Page 45: Top Tether Anchor
Lower Anchors Top Tether Anchor Lower anchors (A) are metal bars built into the vehicle. A top tether (A, C) anchors the top of the child restraint There are two lower anchors for each LATCH seating to the vehicle. A top tether anchor is built into the position that will accommodate a child restraint with vehicle.
Page 46 Lower Anchor and Top Tether Anchor Some top tether-equipped child restraints are designed for use with or without the top tether being Locations attached. Others require the top tether always to be attached. In Canada, the law requires that (Top Tether Anchor): forward-facing child restraints have a top tether, Seating positions with top and that the tether be attached.
Page 47: Securing A Child Restraint Designed For The Latch System
There are covered top tether anchors for each seating Accident statistics show that children are safer if they position located on the back panel of your vehicle, are restrained in the rear rather than the front seat. See behind the rear seat. Remove the trim covers to access Where to Put the Restraint on page 1-36 for additional the anchor.
Page 48 1.4. Place the child restraint in the vehicle, near the seating position that you are using. CAUTION: 1.5. Route the top tether according to your child restraint instructions and the following Each top tether anchor and lower anchor in the instructions: vehicle is designed to hold only one child If the position you are...
Page 49 If the position you are using 2. Attach and tighten the lower attachments to the has an adjustable head lower anchors. If the child restraint does not have restraint and you are using lower attachments or the desired seating position a single tether, route the does not have lower anchors, secure the child tether under the head...
Page 50: Securing A Child Restraint In A Rear Seat Position
Securing a Child Restraint in a Rear Seat Position There is limited space in the rear seating area. If you want to secure a child restraint in a rear outboard seating position, be sure to study the instructions that came with your child restraint to see if there is enough room to secure your seat properly.
Page 51 4. Pull the rest of the shoulder belt all the way out of 5. To tighten the belt, push down on the child restraint, the retractor to set the lock. pull the shoulder portion of the belt to tighten the lap portion of the belt and feed the shoulder belt back into the retractor.
Page 52: Securing A Child Restraint In The Right Front Seat Position
6. If your child restraint manufacturer recommends A label on your sun visor says, “Never put a rear-facing using a top tether, attach and tighten the top child seat in the front.” This is because the risk to the tether to the top tether anchor. Refer to the rear-facing child is so great, if the airbag deploys.
Page 53 If your child restraint is equipped with the LATCH 2. Put the child restraint on the seat. system, see Lower Anchors and Tethers for Children 3. Pick up the latch plate, and run the lap and shoulder (LATCH) on page 1-38. portions of the vehicle’s safety belt through or There is no top tether anchor at the right front seating around the restraint.
Page 54 5. Pull the rest of the shoulder belt all the way out of 6. To tighten the belt, push down on the child the retractor to set the lock. restraint, pull the shoulder portion of the belt to tighten the lap portion of the belt and feed the shoulder belt back into the retractor.
Page 55: Airbag System
If a child restraint has been installed and the on Here are the most important things to know about the indicator is lit, turn the vehicle off. Remove the child airbag system: restraint from the vehicle and reinstall the child restraint. If after reinstalling the child restraint and restarting CAUTION: the vehicle, the on indicator is still lit, check to make...
Page 56 CAUTION: CAUTION: Airbags inﬂate with great force, faster than the Anyone who is up against, or very close to, blink of an eye. If you are too close to an any airbag when it inﬂates can be seriously inﬂating airbag, as you would be if you were injured or killed.
Page 57: Where Are The Airbags
Where Are the Airbags? There is an airbag readiness light on the instrument panel cluster, which shows the airbag symbol. The system checks the airbag electrical system for malfunctions. The light tells you if there is an electrical problem. See Airbag Readiness Light on page 3-30 for more information.
Page 58 CAUTION: If something is between an occupant and an airbag, the bag might not inﬂate properly or it might force the object into that person causing severe injury or even death. The path of an inﬂating airbag must be kept clear. Do not put anything between an occupant and an airbag, and do not attach or put anything on the steering wheel hub or on or near any other...
Page 59: When Should An Airbag Inﬂate
When Should an Airbag Inﬂate? If the front of your vehicle goes straight into a wall that does not move or deform, the threshold level for the reduced deployment is about 10 to 16 mph The driver’s and right front passenger’s frontal airbags (16 to 25 km/h), and the threshold level for a full are designed to inﬂate in moderate to severe frontal deployment is about 20 to 30 mph (32 to 48 km/h).
Page 60: What Makes An Airbag Inﬂate
How Does an Airbag Restrain? Vehicles with dual stage airbags are also equipped with special sensors which enable the sensing system to monitor the position of both the driver and passenger In moderate to severe frontal or near-frontal collisions, front seats. The seat position sensor provides even belted occupants can contact the steering wheel or information which is used to determine if the airbags the instrument panel.
Page 61 Airbag inﬂation does not prevent the driver from seeing In many crashes severe enough to inﬂate an airbag, out of the windshield or being able to steer the vehicle, windshields are broken by vehicle deformation. nor does it stop people from leaving the vehicle. Additional windshield breakage may also occur from the right front passenger airbag.
Page 62: Passenger Sensing System
Passenger Sensing System The passenger sensing system will turn off the right front passenger’s frontal airbag under certain conditions. The driver’s airbag and the side airbags are not part Your vehicle has a passenger sensing system. of the passenger sensing system. The passenger airbag status indicator will be visible when you turn your ignition key to START or RUN.
Page 63 The passenger sensing system is designed to turn off the right front passenger’s frontal airbag if: CAUTION: • the right front passenger seat is unoccupied • the system determines that an infant is present in a A child in a rear-facing child restraint can be rear-facing infant seat seriously injured or killed if the right front •...
Page 64 If after reinstalling the child restraint and restarting the If a person of adult-size is sitting in the right front vehicle, the on indicator is still lit, check to make sure passenger’s seat, but the off indicator is lit, it could be that the vehicle’s seatback is not pressing the child because that person is not sitting properly in the seat.
Page 65 Aftermarket equipment, such as seat covers, can affect how well the passenger sensing system operates. CAUTION: You may want to consider not using seat covers or other aftermarket equipment if your vehicle has the passenger sensing system. See Adding Equipment to Your If the airbag readiness light in the instrument Airbag-Equipped Vehicle on page 1-60 for more panel cluster ever comes on and stays on, it...
Page 66: Servicing Your Airbag-Equipped Vehicle
Servicing Your Airbag-Equipped Adding Equipment to Your Vehicle Airbag-Equipped Vehicle Airbags affect how your vehicle should be serviced. There are parts of the airbag system in several places Is there anything I might add to the front or around your vehicle. You do not want the system to sides of the vehicle that could keep the inﬂate while someone is working on your vehicle.
Page 67: Restraint System Check
Restraint System Check Because I have a disability, I have to get my vehicle modiﬁed. How can I ﬁnd out whether this will affect my advanced airbag system? Checking the Restraint Systems Changing or moving any parts of the front seats, Now and then, make sure the safety belt reminder light safety belts, the airbag sensing and diagnostic and all your belts, buckles, latch plates, retractors...
Page 68: Replacing Restraint System Parts
Replacing Restraint System Parts If the LATCH system was being used during a more severe crash, you may need new LATCH system parts. After a Crash If belts are cut or damaged, replace them. Collision damage also may mean you will need to have LATCH system, safety belt or seat parts repaired or replaced.
Page 69: Features And Controls
Section 2 Features and Controls Keys ...............2-2 Shifting Into Park (P) ........2-24 Remote Keyless Entry System ......2-3 Shifting Out of Park (P) .........2-25 Remote Keyless Entry System Operation ...2-4 Parking Over Things That Burn .......2-26 Engine Exhaust ..........2-26 Doors and Locks ..........2-7 Running the Engine While Parked ....2-27 Door Locks ............2-7 Power Door Locks ..........2-8...
Page 70: Keys
Keys CAUTION: Leaving children in a vehicle with the ignition key is dangerous for many reasons. They could operate the power windows or other controls or even make the vehicle move. The children or others could be badly injured or even killed. Do not leave the keys in a vehicle with children.
Page 71: Remote Keyless Entry System
Remote Keyless Entry System Your vehicle has one double-sided key for the ignition and all Your keyless entry system operates on a radio door locks as well as frequency subject to Federal Communications the spare tire hoist lock, Commission (FCC) Rules and with Industry Canada. if equipped.
Page 72: Remote Keyless Entry System Operation
Remote Keyless Entry System At times you may notice a decrease in range. This is normal for any remote keyless entry system. If the Operation transmitter does not work or if you have to stand closer to your vehicle for the transmitter to work, try this: You can lock and unlock your doors from about 3 feet •...
Page 73: Battery Replacement
Battery Replacement (Lock): Press this button once to lock all of the doors. Pressing lock again within three seconds may Under normal use, the battery in your remote keyless cause the horn to chirp for lock conﬁrmation. You can entry transmitter should last about two years. choose different feedback options for each press of the lock button.
Page 74 To replace the battery in the keyless entry transmitter, 3. Align the covers and snap them together. do the following: 4. Resynchronize the transmitter. See “Resynchronization” following this information. 5. Check the operation of the transmitter. Resynchronization Resynchronization may be necessary due to the security method used by this system.
Page 75: Doors And Locks
Doors and Locks There are several ways to lock and unlock your vehicle. To unlock the door from the outside, use the keyless entry system or the key. Door Locks To unlock or lock the door from the inside, slide the manual lever forward CAUTION: or rearward.
Page 76: Power Door Locks
Power Door Locks Delayed Locking When locking the doors with the power lock switch or If your vehicle is equipped the keyless entry transmitter and a door or the liftgate with power door locks, is open, the delayed locking feature will delay locking the press the raised side of the doors until ﬁve seconds after the last door is closed.
Page 77: Programmable Automatic
Programmable Automatic To remove the tailgate, do the following: 1. Raise the tailgate Door Locks slightly and release both retaining cable Your vehicle is equipped with an automatic lock/unlock clips. To release feature which enables you to program your vehicle’s the retaining cable power door locks.
Page 78: Windows
Windows CAUTION: Leaving children, helpless adults, or pets in a vehicle with the windows closed is dangerous. They can be overcome by the extreme heat and suffer permanent injuries or even death from heat stroke. Never leave a child, a helpless adult, or a pet alone in a vehicle, especially with the windows closed in warm or hot weather.
Page 79: Power Windows
Power Windows The driver’s door has a switch for the passenger windows as well. Your power windows will work when the ignition has been turned to ACCESSORY or RUN or when Retained Accessory Power (RAP) is active. See Retained Accessory Power (RAP) on page 2-16. Press the switch to lower the window.
Page 80: Sliding Rear Window
Window Lockout Sun Visors Sun Visors with Slide Rod (Lockout): Your vehicle has a lockout feature to prevent passengers from operating the power windows. Your vehicle may have this feature. The lockout switch is located in front of the window switches on the driver’s door.
Page 81: Theft-Deterrent Systems
Theft-Deterrent Systems If the lock button on the remote keyless entry transmitter is pressed, but a door is open, you may hear three chimes indicating delayed locking is enabled. Vehicle theft is big business, especially in some cities. See Delayed Locking on page 2-8 for additional Although your vehicle has a number of theft-deterrent information.
Page 82: Testing The Alarm
Testing the Alarm The horn may chirp for 10 seconds before the alarm goes off if the theft-deterrent system is activated using The alarm can be tested by following these steps: the remote keyless entry transmitter and the driver’s door is opened. If this occurs, you can turn off the alarm 1.
Page 83: Passlock
® Passlock Starting and Operating Your Vehicle Your vehicle is equipped with the ® Passlock theft-deterrent system. New Vehicle Break-In ® Passlock is a passive theft-deterrent system. ® Passlock enables fuel if the ignition lock cylinder is Notice: Your vehicle does not need an elaborate turned with a valid key.
Page 84: Ignition Positions
Ignition Positions Notice: Using a tool to force the key from the ignition switch could cause damage or break the key. Use the correct key and turn the key only with your hand. Make sure the key is all the way in. If it is, turn the steering wheel left and right while you turn the key hard.
Page 85: Starting The Engine
Starting the Engine 2. If it does not start within 10 seconds, push the accelerator pedal all the way to the ﬂoor, while you hold the ignition key in START. When the engine Your vehicle is equipped with Starter Motor Control. starts, let go of the key and let up on the accelerator This feature assists in starting the engine and protects pedal.
Page 86: Engine Coolant Heater
Engine Coolant Heater 3. Plug it into a normal, grounded 110-volt AC outlet. Your vehicle may be equipped with an engine coolant CAUTION: heater. In very cold weather, 0°F (−18°C) or colder, the engine coolant heater can help. You will get easier starting Plugging the cord into an ungrounded outlet and better fuel economy during engine warm-up.
Page 87: Automatic Transmission Operation
Automatic Transmission Operation CAUTION: Your vehicle is equipped with an automatic transmission and features an electronic shift position indicator located within the instrument panel cluster. It is dangerous to get out of your vehicle if the shift lever is not fully in PARK (P) with the parking brake ﬁrmly set.
Page 88 REVERSE (R): Use this gear to back up. CAUTION: Notice: Shifting to REVERSE (R) while your vehicle is moving forward could damage the transmission. The repairs would not be covered by your warranty. Shifting into a drive gear while your engine is Shift to REVERSE (R) only after your vehicle is running at high speed is dangerous.
Page 89 DRIVE (D): This position is for normal driving. If you If you manually select SECOND (2), the transmission need more power for passing, and you are: will drive in second gear. You may use this feature for reducing the speed of the rear wheels when you are •...
Page 90: Tow/Haul Mode
Tow/Haul Mode When Tow/Haul is activated the Tow/Haul symbol will illuminate on the instrument panel cluster. See Tow/Haul Mode under Towing a Trailer on page 4-49 for more information. Your vehicle may be equipped with a Tow/Haul mode. The switch is located on the end of the column shift lever.
Page 91: Parking Brake
Parking Brake If the ignition is on when the parking brake is released, the brake system warning light will go off. To set the parking brake, hold the regular brake pedal Notice: Driving with the parking brake on can down with your right foot. Push down the parking overheat the brake system and cause premature brake pedal with your left foot.
Page 92: Shifting Into Park (P)
Shifting Into Park (P) Leaving Your Vehicle With the Engine Running CAUTION: CAUTION: It can be dangerous to get out of your vehicle if the shift lever is not fully in PARK (P) with It can be dangerous to leave your vehicle with the parking brake ﬁrmly set.
Page 93: Shifting Out Of Park (P)
Torque Lock Shifting Out of Park (P) If you are parking on a hill and you do not shift your Automatic Transmission vehicle into PARK (P) properly, the weight of the vehicle may put too much force on the parking pawl in the Your vehicle has an automatic transmission shift lock transmission.
Page 94: Parking Over Things That Burn
Parking Over Things That Burn Engine Exhaust CAUTION: Engine exhaust can kill. It contains the gas carbon monoxide (CO), which you cannot see or smell. It can cause unconsciousness and death. You might have exhaust coming in if: • Your exhaust system sounds strange or different.
Page 95: Running The Engine While Parked
Running the Engine While Parked CAUTION: It is better not to park with the engine running. But if you ever have to, here are some things to know. It can be dangerous to get out of your vehicle if the shift lever is not fully in PARK (P) with CAUTION: the parking brake ﬁrmly set.
Page 96: Mirrors
Mirrors Temperature and Compass Display Press the on/off button, located to the far left, brieﬂy to turn the compass/temperature display on or off. Automatic Dimming Rearview Mirror ® If the display reads CAL, you will need to calibrate the with OnStar , Compass and compass.
Page 97: Automatic Dimming Mirror Operation
Automatic Dimming Mirror Operation To adjust for compass variance do the following: 1. Find your current location and variance zone The automatic dimming mirror function is turned on number on the following zone map. automatically each time the ignition is started. To operate the automatic dimming mirror, do the following: 1.
Page 98: Compass Calibration
3. Keep pressing the on/off button until the desired In order to calibrate, CAL must be displayed in the zone number appears in the display. Release the mirror compass windows. If CAL is not displayed, push button. After approximately four seconds of the on/off button for approximately 12 seconds or inactivity, the new zone number will be locked in until CAL is displayed.
Page 99: Outside Power Mirrors
Outside Power Mirrors Outside Power Foldaway Mirrors If your vehicle is equipped If your vehicle is equipped with outside power mirrors, with this feature, the the controls are located controls are located on the on the driver’s door driver’s door armrest. armrest.
Page 100: Outside Automatic Dimming Mirror
Outside Automatic Dimming Mirror The mirrors may also include a memory function which works together with the memory seats. See Memory Seat on page 2-44 for more information. The driver’s outside mirror will adjust for the glare of any headlamps behind you. This feature is controlled by To fold or unfold the mirrors, move the selector switch, the on and off settings on the electrochromic mirror.
Page 101: Outside Convex Mirror
® Outside Convex Mirror OnStar System Your passenger’s side mirror is convex. A convex mirror’s surface is curved so you can see more from the driver’s seat. CAUTION: A convex mirror can make things (like other ® vehicles) look farther away than they really are. OnStar uses global positioning system (GPS) satellite technology, wireless communications, and live...
Page 102: Onstar Services
® Safe and Sound Plan A complete OnStar User’s Guide and the Terms and ® Conditions of the OnStar Subscription Service • Automatic Notiﬁcation of Airbag Deployment Agreement are included in the vehicle’s glove box • literature. For more information, visit www.onstar.com or Emergency Services ®...
Page 103: Steering Wheel Controls
® ® OnStar Personal Calling OnStar Steering Wheel Controls ® As an OnStar subscriber, the Personal Calling Your vehicle may be capability allows you to make hands-free calls using a equipped with a Talk/Mute wireless system that is integrated into the vehicle. button that can be used Calls can be placed nationwide using simple voice ®...
Page 104: Universal Home Remote System
Universal Home Remote If your vehicle is equipped with the Universal Home Remote Transmitter, it complies with Part 15 of the System FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Page 105: Universal Home Remote System Operation
Universal Home Remote System Be sure that people and objects are clear of the garage door or gate operator you are programming. When Operation programming a garage door, it is advised to park outside of the garage. Do not use the Universal Home Remote with any It is recommended that a new battery be installed in garage door opener that does not have the “stop and your hand-held transmitter for quicker and more...
Page 106 3. Simultaneously press and hold both the desired 6. Locate in the garage, the garage door opener Universal Home Remote button and the hand-held receiver (motor-head unit). Locate the “Learn” transmitter button. Do not release the buttons or “Smart” button. This can usually be found where until Step 4 has been completed.
Page 107: Gate Operator And Canadian Programming
Gate Operator and Canadian Using Universal Home Remote Programming Press and hold the appropriate Universal Home Remote button for at least half of a second. The indicator light Canadian radio-frequency laws require transmitter will come on while the signal is being transmitted. signals to time out or quit after several seconds of transmission.
Page 108: Storage Areas
Reprogramming a Single Universal Cupholder(s) Home Remote Button Your vehicle may be equipped with cupholders for the front and rear seat passengers, located in the center To program a device to Universal Home Remote using console and on the rear of the center console storage a Universal Home Remote button previously trained, area.
Page 109: Tonneau Cover
Tonneau Cover If your vehicle is equipped with a tonneau cover, follow the directions below to remove the cover. 1. To remove, unsnap the cover. Roll it up and stow it using the buckle and the strap located at the front of the box. A.
Page 110 4. To add cargo to the box, remove all bows and the back rail and stow them safely. To clean the tonneau cover, use mild soap and water. If necessary, use a soft bristle brush to remove dirt 3. Remove the two bows by gently pushing them trapped in the grain of the material.
Page 111: Sunroof
Sunroof The sunroof also has a roller sunscreen that can be used to block the rays of the sun. The roller sunscreen can be manually operated with the sunroof in an The vehicle may be equipped with a power sliding open or closed position.
Page 112: Memory Seat
Memory Seat To store the memory settings, do the following: 1. While the vehicle is in PARK (P), adjust the driver’s If your vehicle has this seat, including the seatback recliner, lumbar, and feature, the controls for side wing area, and both outside mirrors to the memory function your preference.
Page 113: Easy Exit Seat
Easy Exit Seat To use the seat exit position, do one of the following: • Press the exit button on the memory control, or The controls for this memory function are located on the • driver’s door. If this feature is activated in the DIC, removing the key from the ignition will move the seat to the exit (Easy Exit Seat): This button is used to program position.
Page 114 NOTES 2-46...
Page 115 Section 3 Instrument Panel Instrument Panel Overview .......3-4 Entry Lighting ..........3-18 Hazard Warning Flashers ........3-6 Exit Lighting ..........3-18 Other Warning Devices ........3-6 Front Reading Lamps ........3-18 Horn .............3-6 Cargo Lamp ..........3-19 Tilt Wheel .............3-6 Battery Run-Down Protection ......3-19 Turn Signal/Multifunction Lever ......3-7 Accessory Power Outlet(s) ......3-19 Turn and Lane-Change Signals ......3-8 Ashtray(s) and Cigarette Lighter ......3-20...
Page 116 Section 3 Instrument Panel Brake System Warning Light ......3-34 Audio System(s) ..........3-62 Anti-Lock Brake System Warning Light .....3-35 Setting the Time ...........3-64 Engine Coolant Temperature Gage ....3-36 Radio with Cassette and CD ......3-64 Transmission Temperature Gage .....3-36 Navigation/Radio System .......3-79 Malfunction Indicator Lamp ......3-38 Rear Seat Entertainment System ....3-79 Oil Pressure Gage ........3-41...
Page 117 NOTES...
Page 118: Instrument Panel Overview
Instrument Panel Overview...
Page 119 The main components of your instrument panel are the following: A. Dome Lamp Override Button. See Dome Lamp L. Hood Release. See Hood Release on page 5-9. Override on page 3-18. M. Fog Lamps Button. See Fog Lamps on page 3-17. B.
Page 120: Hazard Warning Flashers
Hazard Warning Flashers Other Warning Devices Your hazard warning ﬂashers let you warn others. They If you carry reﬂective triangles, you can set them up at also let police know you have a problem. Your front the side of the road about 300 feet (100 m) behind and rear turn signal lamps will ﬂash on and off.
Page 121: Turn Signal/Multifunction Lever
Turn Signal/Multifunction Lever The lever on the left side of the steering column includes the following: • The tilt steering wheel lever is located on the lower left Turn and Lane Change Signals. See Turn and side of the column. Lane-Change Signals on page 3-8.
Page 122: Turn And Lane-Change Signals
Turn and Lane-Change Signals Turn Signal On Chime If your turn signal is left on for more than 3/4 of a mile The turn signal has two upward (for right) and (1.2 km), a chime will sound at each ﬂash of the turn two downward (for left) positions.
Page 123: Flash-To-Pass
Flash-to-Pass (Delay): You can set the wiper speed for a long or short delay between wipes. This can be very useful This feature lets you use your high-beam headlamps to in light rain or snow. Turn the band to choose the delay signal a driver in front of you that you want to pass.
Page 124: Windshield Washer
Windshield Washer Cruise Control (Washer Fluid): There is a paddle marked (Off): This position with the windshield washer symbol at the top of turns the system off. the multifunction lever. To spray washer ﬂuid on the windshield, push the paddle. The wipers will clear the window and then either stop or return to your preset speed.
Page 125: Setting Cruise Control
Setting Cruise Control With cruise control, you can maintain a speed of about 25 mph (40 km/h) or more without keeping your foot on the accelerator. This can really help on long trips. Cruise control does not work at speeds below CAUTION: about 25 mph (40 km/h).
Page 126: Resuming A Set Speed
Resuming a Set Speed Increasing Speed While Using Cruise Control Suppose you set your cruise control at a desired speed and then you apply the brake. This, of course, There are two ways to go to a higher speed: disengages the cruise control. But you don’t need •...
Page 127 Reducing Speed While Using Using Cruise Control on Hills Cruise Control How well your cruise control will work on hills depends upon your speed, load and the steepness of the hills. • Press in the button at the end of the lever until you When going up steep hills, you may want to step on the reach the lower speed you want, then release it.
Page 128: Headlamps
Headlamps AUTO (Automatic): Turning the control to this position puts the system into automatic headlamp mode. (Parking Lamps): Turning the control to this position turns on the parking lamps, together with the following: • Sidemarker Lamps • Taillamps • License Plate Lamps •...
Page 129: Daytime Running Lamps (Drl)
Daytime Running Lamps (DRL) When you turn the exterior lamp control to off, the headlamps will go off, and your DRL lamps will illuminate, provided it is not dark outside. Daytime Running Lamps (DRL) can make it easier for others to see the front of your vehicle during the day. Shifting the transmission into PARK (P) will allow you DRL can be helpful in many different driving conditions, to idle the vehicle with the DRL off.
Page 130: Puddle Lamps
Your vehicle is equipped with a light sensor located on To idle your vehicle with the automatic headlamp the top of the instrument panel in the defroster grille. system off, turn the control to the off position. Be sure it is not covered, or the system will be on You may be able to turn off your Automatic Headlamp whenever the ignition is on.
Page 131: Fog Lamps
Fog Lamps The fog lamps will go off whenever the high-beam headlamps come on. When the high beams go off, the fog lamps will come on again. You can use your vehicle’s fog lamps for better vision in foggy or misty conditions. The fog lamps will be cancelled after the ignition is turned off.
Page 132: Dome Lamps
Dome Lamps Entry Lighting The dome lamps will come on when you open a door Your vehicle is equipped with an illuminated entry and the dome override button is in the out position. feature. You can also turn the dome lamps on by turning the When a door is opened, the dome lamps and puddle instrument panel brightness thumbwheel, located next lamps will come on if the dome override button is in the...
Page 133: Cargo Lamp
Cargo Lamp Accessory Power Outlet(s) With accessory power outlets you can plug in auxiliary The cargo lamp button is electrical equipment such as a cellular telephone or located on the left side of other devices designed to operate with vehicle the instrument panel.
Page 134: Ashtray(S) And Cigarette Lighter
Ashtray(s) and Cigarette Lighter Certain electrical accessories may not be compatible with the accessory power outlets and could result in blown vehicle or adapter fuses. If you experience a The ashtray is located in the center console, if equipped. problem, see your dealer for additional information Press the raised area on the access door to use the on accessory power outlets.
Page 135: Climate Controls
Climate Controls Driver’s Side Temperature Knob The driver’s side knob is used to adjust the temperature of the air coming through the system on the driver’s Dual Automatic Climate Control side. The temperature can be adjusted even if the System system is turned off.
Page 136: Automatic Operation
Turn the knob counterclockwise or clockwise to lower or If the driver’s and passenger’s temperature settings increase the cabin temperature. The display will show are the same when AUTO is pressed, the the temperature setting decreasing or increasing and an temperature setting and both arrows will be arrow pointing to the passenger will be displayed displayed for ﬁve seconds along with the automatic...
Page 137: Manual Operation
2. Set the driver’s and passenger’s temperature. (Off): Press this button to turn off the entire To ﬁnd your comfort setting, start with a 74°F (23°C) climate control system. Outside air will still enter temperature setting and allow about 20 minutes the vehicle, and will be directed to the ﬂoor.
Page 138 (Mode): Press this button to manually change the (Recirculation): Press this button to limit the direction of the airﬂow in your vehicle. Repeatedly press amount of outside air entering your vehicle. The light on the button until the desired mode appears on the the recirculation button will glow.
Page 139 On cool, but sunny days while using manual operation (Air Conditioning): Press this button to turn of the automatic system, use bi-level to deliver warm the air conditioning (A/C) compressor on and off. air to the ﬂoor and cooler air to the instrument panel The snowﬂake symbol will appear on the display when outlets.
Page 140: Rear Window Defogger
< Defogging and Defrosting (Rear): Press this button to turn on or off the rear window defogger and heated mirrors, if equipped. You can use either defog or front defrost to clear fog or An indicator light in the button will come on to let you frost from your windshield.
Page 141: Warning Lights, Gages, And Indicators
Operation Tips Warning lights come on when there may be or is a problem with one of your vehicle’s functions. As you will • Keep the hood and front air inlets free of ice, see in the details on the next few pages, some warning snow, or any other obstruction (such as leaves).
Page 142: Instrument Panel Cluster
Instrument Panel Cluster Your instrument panel cluster is designed to let you know at a glance how your vehicle is running. You’ll know how fast you’re going, about how much fuel you have and many other things you’ll need to know to drive safely and economically.
Page 143: Speedometer And Odometer
Speedometer and Odometer Trip Odometer Your speedometer lets you see your speed in both The trip odometer can tell you how far your vehicle miles per hour (mph) and kilometers per hour (km/h). has been driven since you last set the trip odometer Your odometer shows how far your vehicle has to zero.
Page 144: Safety Belt Reminder Light
Safety Belt Reminder Light Airbag Readiness Light When the key is turned to RUN or START, a chime will There is an airbag readiness light on the instrument come on for several seconds to remind people to panel cluster, which shows the airbag symbol. fasten their safety belts, unless the driver’s safety belt is The system checks the airbag’s electrical system for already buckled.
Page 145: Passenger Airbag Status Indicator
Passenger Airbag Status Indicator Your vehicle has a rear seat that will accommodate a rear-facing child restraint. A label on your sun visor says, “Never put a rear-facing child seat in the front.” This is Your vehicle has the passenger sensing system. Your because the risk to the rear-facing child is so great, rearview mirror has a passenger airbag status indicator.
Page 146 If the word ON or the on symbol is lit on the passenger If, after several seconds, all status indicator lights airbag status indicator, it means that the right front remain on, or if there are no lights at all, there may passenger’s frontal airbag is enabled (may inﬂate).
Page 147: Battery Warning Light
Battery Warning Light Voltmeter Gage If this light is displayed When your engine is not when the engine is running, but the ignition is running, you may have a in RUN, this gage problem with your charging shows your battery’s state system.
Page 148: Brake System Warning Light
Brake System Warning Light Readings in the low warning zone may occur when a large number of electrical accessories are operating in the vehicle and the engine is left at an idle for an With the ignition on, the brake system warning light extended period.
Page 149: Anti-Lock Brake System Warning Light
Anti-Lock Brake System If the light comes on while you are driving, pull off the road and stop carefully. You may notice that the pedal is Warning Light harder to push or may go closer to the ﬂoor. It may take longer to stop.
Page 150: Engine Coolant Temperature Gage
Engine Coolant Temperature Gage Transmission Temperature Gage United States Canada United States Canada This gage shows the engine coolant temperature. Your vehicle may be equipped with a transmission temperature gage. It also provides an indicator of how hard your vehicle is working.
Page 151 At approximately 265°F (130°C), the message center Notice: If you drive your vehicle with the will display a TRANSMISSION HOT message and transmission temperature gage above normal the transmission will enter a transmission protection operating range, you can damage the transmission. mode.
Page 152: Malfunction Indicator Lamp
Malfunction Indicator Lamp Notice: Modiﬁcations made to the engine, transmission, exhaust, intake, or fuel system of your vehicle or the replacement of the original tires Check Engine Light with other than those of the same Tire Performance Criteria (TPC) can affect your vehicle’s emission Your vehicle is equipped controls and may cause this light to come on.
Page 153: If The Light Is Flashing
If the Light is Flashing If the Light Is On Steady The following may prevent more serious damage to You may be able to correct the emission system your vehicle: malfunction by considering the following: • Reducing vehicle speed Did you recently put fuel into your vehicle? •...
Page 154: Emissions Inspection And Maintenance Programs
Emissions Inspection and Maintenance Have you recently changed brands of fuel? Programs If so, be sure to fuel your vehicle with quality fuel. See Gasoline Octane on page 5-4. Poor fuel quality will Some state/provincial and local governments have or cause your engine not to run as efficiently as designed.
Page 155: Maintenance Schedule
Oil Pressure Gage A reading in the low pressure zone may be caused by a dangerously low oil level or some other problem causing low oil pressure. Check your oil as soon as possible. See DIC Warnings and Messages on page 3-47 and Engine Oil on page 5-12.
Page 156: Security Light
Security Light Highbeam On Light This light ﬂashes when the This light will come on vehicle security system is when the high-beam activated. headlamps are in use. See Headlamp High/Low-Beam Changer on page 3-8. Cruise Control Light Tow/Haul Mode Light This light comes on whenever you set your This light is displayed...
Page 157: Cargo Lamp Light
Cargo Lamp Light The gage will ﬁrst indicate empty before you are out of fuel, and you should get more fuel as soon as possible. Here are some situations you may experience with This light will come on your fuel gage. None of these indicate a problem with when the cargo lamp is in the fuel gage.
Page 158: Driver Information Center (Dic)
Driver Information Center (DIC) (Customization): Press this button to access the vehicle settings menu and customize the personal The Driver Information Center (DIC) display is located settings on your vehicle. on the instrument panel cluster, below the speedometer. The DIC buttons are located on the steering wheel. (Select): Press this button to reset certain DIC The DIC can display information such as the trip functions and set your customization settings.
Page 159: Trip Information Button
Trip Information Button You can also reset TRIP A or TRIP B while they are displayed by pressing the reset stem on the cluster. If you press and hold the reset stem or the select button (Trip Information): Press the trip information for four seconds, the display will show the distance button to scroll through the ODOMETER, TRIP A, traveled since the last ignition cycle for TRIP A or...
Page 160: Maintenance Schedule
Fuel Information Button Press and hold the select button for one second while AVG ECON is displayed to reset the average fuel economy. Average fuel economy will then be calculated (Fuel Information): Press the fuel information starting from that point. If the average fuel economy button to scroll through the range, fuel used, average is not reset, it will be continually updated each time fuel economy, and the engine oil life system.
Page 161: Dic Warnings And Messages
Customization Button Some messages may not require immediate action, but you should press any of the four DIC buttons on the steering wheel or the trip odometer reset stem on the (Customization): Press the customization button to instrument panel cluster to acknowledge that you access the VEHICLE SETTINGS menu and customize received the messages and to clear them from the the settings to your vehicle.
Page 162: Buckle Passenger
BUCKLE PASSENGER BUCKLE SEATBELT If your vehicle has the passenger sensing system, this If your vehicle has the passenger sensing system, this message reminds you to buckle the passenger’s seat message reminds you to buckle the driver’s seat belt. See Passenger Sensing System on page 1-56. belt.
Page 163: Change Engine Oil
CHANGE ENGINE OIL CHECK OIL LEVEL This message is displayed for 10 seconds at the start of If the oil level in the vehicle is low, this message will each ignition cycle when the engine oil needs to be appear on the DIC. Check the oil level and correct it as changed.
Page 164: Driver Door Ajar
DRIVER DOOR AJAR ENGINE OVERHEATED If the driver’s door is not fully closed, this message Notice: If you drive your vehicle while the engine will appear on the display and you will hear a chime. is overheating, severe engine damage may occur. Stop and turn off the vehicle, check the door for If an overheat warning appears on the instrument obstacles and close the door again.
Page 165: Keyfob X Battery Low
KEYFOB X BATTERY LOW OIL LIFE RESET If a remote keyless entry transmitter battery is low, This message will appear on the display for about this message will appear on the DIC. The battery 10 seconds after resetting the change engine oil needs to be replaced in the transmitter.
Page 166: Passenger Door Ajar
PASSENGER DOOR AJAR SERVICE 4WD (Four-Wheel-Drive) If the passenger’s door is not fully closed, this message If a problem occurs with the all-wheel-drive system, will appear on the display and you will hear a chime. this message will appear on the DIC. If this message Stop and turn off the vehicle, check the door for appears, stop as soon as possible and turn off the obstacles and close the door again.
Page 167: Service Brake Booster
SERVICE BRAKE BOOSTER If your vehicle has vacuum assist power brakes, this message will be displayed on the DIC when there is a problem with the Supplemental Brake Assist system. If the message is displayed immediately after starting CAUTION: the vehicle or the message appears while driving, your Supplemental Brake Assist system needs service.
Page 168: Service Charging System
SERVICE CHARGING SYSTEM TRANS (Transmission) HOT IDLE ENGINE On some vehicles, if there is a problem with the battery charging system, this message will appear on the DIC. Notice: If you drive your vehicle while the Under certain conditions, the battery warning light transmission ﬂuid is overheating and the may also turn on in the instrument panel cluster.
Page 169: Transmission Hot
TRANSMISSION HOT If the vehicle has the Tow/Haul mode, use this feature if the transmission is operating at higher temperatures Notice: If you drive your vehicle while the and/or the following situations exist, which can cause the transmission ﬂuid is overheating and the transmission to operate at higher temperatures: transmission temperature warning is displayed on •...
Page 170: Dic Vehicle Customization
TURN SIGNAL ON After pressing the customization button, VEHICLE SETTINGS will momentarily display before going to a If a turn signal is left on for 3/4 of a mile (1.2 km), this customization option. message will appear on the display and you will hear a Lock Doors chime.
Page 171 Unlock Doors When locking the doors with the power lock switch or the keyless entry transmitter and a door is open, Press the customization button until UNLOCK DOORS the delayed locking feature will delay locking the doors appears in the display. To select your preference for until ﬁve seconds after the last door is closed.
Page 172: Unlock Feedback
Lock Feedback Unlock Feedback Press the customization button until LOCK FEEDBACK Press the customization button until UNLOCK appears in the display. To select your preference for FEEDBACK appears in the display. To select your the feedback you receive when locking the vehicle with preference for the feedback you will receive when the remote keyless entry transmitter, press the select unlocking the vehicle with the remote keyless entry...
Page 173 Headlamp Delay Choose one of the available options and press the customization button while it is displayed on the DIC to Press the customization button until HEADLAMP select it and move on to the next feature. DELAY appears in the display. To select your Perimeter Lights preference for how long the headlamps will stay on when you turn off the vehicle, press the select button...
Page 174: Alarm Warning
Easy Exit Seat CURB VIEW: PASSENGER: The passenger’s outside mirror will be tilted down when the vehicle is shifted Press the customization button until EASY EXIT SEAT into REVERSE (R). appears in the display. To select your preference for seat position exit, press the select button while CURB VIEW: DRIVER: The driver’s outside mirror EASY EXIT SEAT is displayed on the DIC.
Page 175 ALARM WARNING: HORN: The horn will chirp when The DIC will begin scrolling through the languages in the alarm is active. their particular language. English will be in English, Francais will be in French and Espanol will be in ALARM WARNING: LAMPS: The headlamps will ﬂash Spanish.
Page 176: Audio System(S)
Audio System(s) CAUTION: Determine which radio your vehicle has and then read the pages following to familiarize yourself with its features. This system provides you with a far greater access to audio stations and song listings. Driving without distraction is a necessity for a safer Giving extended attention to entertainment driving experience.
Page 177 Here are some ways in which you can help avoid Notice: The chime signals related to safety belts, distraction while driving. parking brake, and other functions of your vehicle operate through the GM radio/entertainment system. While your vehicle is parked: If that equipment is replaced or additional •...
Page 178: Setting The Time
Setting the Time Radio with Cassette and CD Press and hold the HR button until the correct hour appears on the display. Press and hold the MN button until the correct minute appears on the display. The time can be set with the ignition on or off. To synchronize the time with an FM station broadcasting Radio Data System (RDS) information, press and hold the hour and minute buttons at the same time until...
Page 179: Playing The Radio
XM™ Satellite Radio Service With RDS, the radio can do the following: • Seek to stations broadcasting the selected type of XM™ is a satellite radio service that is based in programming the 48 contiguous Untied States and in Canada •...
Page 180 INFO (Information): When the ignition is off, press this This feature is most effective at lower radio volume knob to display the time. settings where background noise can affect how well you hear the music being played through your vehicle’s For RDS, press the INFO knob to change what appears audio system.
Page 181: Finding A Station
Finding a Station Setting Preset Stations Up to 30 stations (six FM1, six FM2, and six AM, BAND: Press this button to switch between FM1, FM2, six XM1 and six XM2 (if equipped), can be programed AM, or XM1 or XM2 (if equipped). The display will on the six numbered pushbuttons, by performing the show the selection.
Page 182 Setting the Tone (Bass/Treble) The setting last chosen will appear on the display when you ﬁrst press AUTO EQ. Each time you press this button, another setting will appear on the display and AUDIO: Push and release the AUDIO knob until BASS AUTO EQ will switch to one of the preset settings listed.
Page 183: Rds And Xm
Adjusting the Speakers (Balance/Fade) Finding a Program Type (PTY) Station (RDS and XM™) AUDIO: To adjust the balance between the right and the left speakers, push and release the AUDIO knob To select and ﬁnd a desired PTY perform the following: until BAL appears on the display.
Page 184 Setting Preset PTYs (RDS Only) SCAN: Scan the stations within a PTY by performing the following: These buttons have factory PTY presets. Up to 12 PTYs 1. Press the TYPE button to activate program type (six FM1 and six FM2), can be programmed on the select mode.
Page 185: Rds Messages
RDS Messages Radio Messages INFO (Information): If the current station has a CAL ERR (Calibration Error): The audio system message, the information symbol will appear on has been calibrated for your vehicle from the factory. the display. Press this button to see the message. If CAL ERR appears on the display, it means that The message may display the artist, song title, call in the radio has not been conﬁgured properly for the...
Page 186 XM™ Radio Messages Radio Display Condition Action Required Message XL (Explicit Language XL on the radio display, These channels, or any others, can be blocked at a Channels) after the channel name, customer’s request, by calling 1-800-852-XMXM (9696). indicates content with explicit language.
Page 187 XM™ Radio Messages (cont’d) Radio Display Condition Action Required Message No Info Category Name not No category information is available at this time on this available channel. The system is working properly. No Info No Text/Informational No text or informational messages are available at this message available time on this channel.
Page 188: Playing A Cassette Tape
Playing a Cassette Tape 1 PREV (Previous): The tape must have at least three seconds of silence between each selection for The tape player is built to work best with tapes that are previous to work. Press this pushbutton to go to the up to 30 to 45 minutes long on each side.
Page 189 © ¨ 3 REV (Reverse): Press this pushbutton to quickly SCAN : Press and hold either the SCAN or the reverse the tape. The radio will play while the tape TYPE arrows for more than two seconds until SCAN reverses. Press it again to return to playing speed. appears on the display and you hear a beep.
Page 190: Cassette Tape Messages
Cassette Tape Messages If the cassette tape is not playing correctly, for any other reason, try a known good cassette. CHK TAPE (Check Tape): If this message appears on If any error occurs repeatedly or if an error cannot be the display, the tape will not play due to one of the corrected, contact your GM dealer.
Page 191: Playing A Cd
Playing a CD If there is no apparent damage, try a known good CD. Do not add any label to a CD, it could get caught in the Insert a CD partway into the slot, label side up. CD player. If a CD is recorded on a personal computer The player will pull it in and the CD should begin and a description label is needed, try labeling the top of playing.
Page 192 © ¨ 3 REV (Reverse): Press and hold this pushbutton SCAN : Press and hold either the SCAN or the to quickly reverse within a track. Press and hold this TYPE arrows for more than two seconds until SCAN pushbutton for less than two seconds to reverse at appears on the display and you hear a beep.
Page 193: Navigation/Radio System
CD Messages Navigation/Radio System If the CD comes out, it could be for one of the following Your vehicle may have a navigation radio system. reasons: The navigation system has built-in features intended • It is very hot. When the temperature returns to to minimize driver distraction.
Page 194: Before You Drive
Parental Control Headphones This button is located behind the video screen. Press The RSE system includes two sets of wireless this button while a DVD or CD is playing to freeze headphones. the video and mute the audio. The video screen will Each set of headphones has an ON/OFF control.
Page 195: Stereo Rca Jacks
Battery Replacement Notice: Do not store the headphones in heat or direct sunlight. This could damage the headphones To change the batteries, do the following: and repairs will not be covered by your warranty. Keep the headphones stored in a cool, dry place. 1.
Page 196: Audio Output
Audio Output To use the auxiliary inputs on the RSE system, connect an external auxiliary device to the color-coded Audio from the DVD player or auxiliary inputs may be RCA jacks and turn both the auxiliary device and the heard through the following possible sources: RSE system power on.
Page 197: Dvd Player
Video Screen The DVD player power may be turned on when the ignition is in RUN, ACCESSORY, or when Retained The video screen is located in the overhead console. Accessory Power (RAP) is active. To use the video screen, push forward on the release The RSE system DVD player is only compatible with latch and the screen will fold down.
Page 198 (Main DVD Menu): Press this button to access the DVD menu. The DVD menu is different on every DVD. Use the up, down, left, and right arrow buttons to move the cursor around the DVD menu. After making a selection press the enter button. This button only operates when playing a DVD.
Page 199: Remote Control
Playing a Disc Ejecting a Disc To play a disc, gently insert the disc with the label side Press the eject button on the DVD player faceplate to up into the loading slot. The DVD player will continue eject the disc. There is not an eject button on the remote loading the disc and the player will automatically start, control.
Page 200 Remote Control Buttons (Set-up Menu): Press this button to adjust the color, tint, brightness, contrast, display mode, and dynamic range compression. The dynamic range compression feature can be used to reduce loud audio and increase low audio produced by some DVDs. (Audio): Press this button to display a menu that will only appear when a DVD is being played.
Page 201 1 through 0 (Numeric Keypad): The numeric keypad (Camera Angle): Press this button to change provides you with the capability of direct chapter, camera angles on DVDs that have this feature when a title, and track number selection. DVD is playing. The format and content of this function will vary for each disc.
Page 202 Battery Replacement Problem Recommended Action No power. The ignition might not be To change the batteries, do the following: in on or accessory. 1. Remove the battery compartment door located on The parental control the bottom of the remote control. button might have been turned on.
Page 203 Problem Recommended Action Problem Recommended Action In auxiliary mode, the Check the auxiliary input After stopping the player, If the stop button was picture moves or scrolls. connections at both I push Play but pressed one time, devices. sometimes the DVD the DVD player will Change the Video Format starts where I left off and...
Page 204: Dvd Messages
DVD Messages Problem Recommended Action Sometimes the wireless Check for obstructions, The following errors may be displayed on the video headphone audio cuts out low batteries, reception screen: or buzzes. range, and interference from cellular telephone Disc Format Error: This message will be displayed if a towers or by using your disc is inserted upside down, if the disc is not readable, cellular telephone in the...
Page 205: Rear Seat Audio (Rsa)
DVD Distortion Rear Seat Audio (RSA) There may be an experience with audio distortion in the This feature allows rear seat passengers to listen to any wireless headphones when operating cellular phones, of the sources: radio, cassette tapes, CDs, or DVDs. scanners, CB radios, Global Positioning Systems However, the rear seat passengers can only control the (GPS)*, two-way radios, mobile fax, or walkie talkies.
Page 206 SRC (Source): Press this button to select a source: radio, cassette tapes, CDs, or DVDs. SEEK : When listening to FM1, FM2, or AM, press the up or the down arrow to go to the next or to the previous station and stay there. This function is inactive if the front seat passengers are listening to the radio.
Page 207: Cd Changer
CD Changer PROG (Program): Press this button to go to the next preset radio station set on the pushbuttons on the main radio. This function is inactive if the front seat passengers are listening to the radio. When a cassette tape is playing, press this button to go to the other side of the tape.
Page 208 To load a CD, perform the following steps: To eject a single CD, perform the following steps: 1. Press the LOAD button. Available positions will 1. Press the eject button (upward pointing arrow). blink green. The buttons with loaded CDs will blink green. 2.
Page 209 CD Functions 6 RDM (Random): Press and release this pushbutton to hear all of the tracks on all of the loaded CDs in All of the CD changer functions are performed by the random, rather than sequential, order. RDM ALL will radio, except for loading and ejecting.
Page 210: Theft-Deterrent Feature
CD Changer Errors Theft-Deterrent Feature ® THEFTLOCK is designed to discourage theft of CHK CD (Check): If this message appears on the display, it could be for one of the following reasons: your vehicle’s radio. The feature works automatically by learning a portion of the Vehicle Identiﬁcation •...
Page 211: Audio Steering Wheel Controls
Audio Steering Wheel Controls PROG (Program): Press this button to play a station you have programmed on the radio preset pushbuttons. The radio will only seek preset stations with a strong signal that are in the selected band. When a cassette tape is playing, press this button to play the other side of the tape.
Page 212: Radio Reception
Radio Reception FM Stereo FM stereo will give the best sound, but FM signals will You may experience frequency interference and reach only about 10 to 40 miles (16 to 65 km). Tall static during normal radio reception if items such as buildings or hills can interfere with FM signals, causing cellphone chargers, vehicle convenience accessories, the sound to fade in and out.
Page 213: Care Of The Cassette Tape Player
Care of the Cassette Tape Player If there is a reduction in sound quality, try a known good cassette to see if the tape or the tape player is at fault. If this other cassette has no improvement in sound A tape player that is not cleaned regularly can cause quality, clean the tape player.
Page 214: Care Of Your Cds And Dvds
Care of Your CDs and DVDs A non-scrubbing action, wet-type cleaner which uses a cassette with a fabric belt to clean the tape head Handle CDs carefully. Store them in their original cases can be used. This type of cleaning cassette will not or other protective cases and away from direct sunlight eject on its own.
Page 215: Fixed Mast Antenna
Fixed Mast Antenna Chime Level Adjustment The ﬁxed mast antenna can withstand most car washes The radio is used to adjust the vehicle’s chime level. without being damaged. If the mast should ever To change the volume level of the chime, press and hold become slightly bent, straighten it out by hand.
Page 216 NOTES 3-102...
Page 217: Driving Your Vehicle
Section 4 Driving Your Vehicle Your Driving, the Road, and Your Vehicle ..4-2 Before Leaving on a Long Trip .......4-33 Defensive Driving ...........4-2 Highway Hypnosis ........4-34 Drunken Driving ..........4-3 Hill and Mountain Roads ........4-34 Control of a Vehicle ........4-6 Winter Driving ..........4-36 Braking ............4-6 If Your Vehicle is Stuck in Sand, Mud, Anti-Lock Brake System (ABS) ......4-7...
Page 218: Your Driving, The Road, And Your Vehicle
Your Driving, the Road, and CAUTION: Your Vehicle Defensive driving really means “Be ready Defensive Driving for anything.” On city streets, rural roads, or expressways, it means “Always expect the The best advice anyone can give about driving is: Drive unexpected.”...
Page 219: Drunken Driving
Drunken Driving Many adults — by some estimates, nearly half the adult population — choose never to drink alcohol, so they never drive after drinking. For persons under 21, Death and injury associated with drinking and driving is it is against the law in every U.S. state to drink alcohol. a national tragedy.
Page 220 According to the American Medical Association, a 180 lb A person who consumes food just before or during (82 kg) person who drinks three 12 ounce (355 ml) drinking will have a somewhat lower BAC level. bottles of beer in an hour will end up with a BAC There is a gender difference, too.
Page 221 But the ability to drive is affected well below a BAC of There is something else about drinking and driving that 0.10 percent. Research shows that the driving skills many people do not know. Medical research shows of many people are impaired at a BAC approaching that alcohol in a person’s system can make crash 0.05 percent, and that the effects are worse at night.
Page 222: Control Of A Vehicle
Control of a Vehicle Average reaction time is about three-fourths of a second. But that is only an average. It might be less with one driver and as long as two or three seconds or You have three systems that make your vehicle go more with another.
Page 223: Anti-Lock Brake System (Abs)
Anti-Lock Brake System (ABS) Avoid needless heavy braking. Some people drive in spurts — heavy acceleration followed by heavy braking — rather than keeping pace with traffic. This is Your vehicle has anti-lock brakes. ABS is an advanced a mistake. Your brakes may not have time to cool electronic braking system that will help prevent a between hard stops.
Page 224 The anti-lock system can change the brake pressure faster than any driver could. The computer is programmed to make the most of available tire and road conditions. This can help you steer around the obstacle while braking hard. Let us say the road is wet and you are driving safely. Suddenly, an animal jumps out in front of you.
Page 225: Braking In Emergencies
Steering Remember: Anti-lock does not change the time you need to get your foot up to the brake pedal or always decrease stopping distance. If you get too close to Power Steering the vehicle in front of you, you will not have time to apply your brakes if that vehicle suddenly slows or stops.
Page 226: Steering In Emergencies
Steering in Emergencies Suppose you are steering through a sharp curve. Then you suddenly accelerate. Both control There are times when steering can be more effective systems — steering and acceleration — have to than braking. For example, you come over a hill and ﬁnd do their work where the tires meet the road.
Page 227: Off-Road Recovery
Off-Road Recovery You may ﬁnd that your right wheels have dropped off the edge of a road onto the shoulder while you are driving. An emergency like this requires close attention and a quick decision. If you are holding the steering wheel at the recommended 9 and 3 o’clock positions, you can turn it a full 180 degrees very quickly without removing either hand.
Page 228: Passing
Passing • Do not get too close to the vehicle you want to pass while you are awaiting an opportunity. For The driver of a vehicle about to pass another on a one thing, following too closely reduces your area two-lane highway waits for just the right moment, of vision, especially if you are following a larger accelerates, moves around the vehicle ahead, then...
Page 229: Loss Of Control
• Loss of Control Check your mirrors, glance over your shoulder and start your left lane change signal before moving out Let us review what driving experts say about what of the right lane to pass. When you are far enough happens when the three control systems —...
Page 230: Off-Road Driving
Off-Road Driving If your vehicle starts to slide, ease your foot off the accelerator pedal and quickly steer the way you want the vehicle to go. If you start steering quickly enough, If your vehicle has 20-inch tire/wheel assemblies, you your vehicle may straighten out.
Page 231 Off-road driving involves some new skills. And that is why it is very important that you read this guide. You will CAUTION: ﬁnd many driving tips and suggestions. These will help make your off-road driving safer and more enjoyable. • Cargo on the load ﬂoor piled higher than Before You Go Off-Roading the seatbacks can be thrown forward...
Page 232: Environmental Concerns
Environmental Concerns Traveling to Remote Areas Off-road driving can provide wholesome and satisfying It makes sense to plan your trip, especially when going recreation. However, it also raises environmental to a remote area. Know the terrain and plan your concerns. We recognize these concerns and urge every route.
Page 233: Scanning The Terrain
Scanning the Terrain Controlling your vehicle is the key to successful off-road driving. One of the best ways to control your vehicle Off-road driving can take you over many different kinds is to control your speed. Here are some things to keep of terrain.
Page 234: Driving On Off-Road Hills
Driving on Off-Road Hills When you drive over obstacles or rough terrain, keep a ﬁrm grip on the steering wheel. Ruts, troughs, or other Off-road driving often takes you up, down, or across a surface features can jerk the wheel out of your hands hill.
Page 235: Approaching A Hill
Approaching a Hill • What is beyond the hill? Is there a cliff, an embankment, a drop-off, a fence? Get out and When you approach a hill, you need to decide if it is walk the hill if you do not know. It is the smart way one of those hills that is just too steep to climb, descend, to ﬁnd out.
Page 236 • Try to drive straight up the hill if at all possible. If the path twists and turns, you might want to CAUTION: ﬁnd another route. Driving to the top (crest) of a hill at full speed CAUTION: can cause an accident. There could be a drop-off, embankment, cliff, or even another vehicle.
Page 237: Driving Downhill
• As you are backing down the hill, put your left hand Suppose, after stalling, I try to back down on the steering wheel at the 12 o’clock position. the hill and decide I just cannot do it. What This way, you will be able to tell if the wheels are should I do? straight and maneuver as you back down.
Page 238 If you decide you can go down a hill safely, then try to Are there some things I should not do when keep your vehicle headed straight down, and use a driving down a hill? low gear. This way, engine drag can help the brakes and they will not have to do all the work.
Page 239: Driving Across An Incline
Driving Across an Incline For reasons like these, you need to decide carefully whether to try to drive across an incline. Just because Sooner or later, an off-road trail will probably go across the trail goes across the incline does not mean you the incline of a hill.
Page 240: Stalling On An Incline
Stalling on an Incline CAUTION: If your vehicle stalls when you are crossing an incline, be sure you, and any passengers, get out on the uphill side, even if the door there is harder to open. Getting out on the downhill (low) side of a If you get out on the downhill side and the vehicle starts vehicle stopped across an incline is to roll over, you will be right in its path.
Page 241: Driving In Water
Driving in Mud, Sand, Snow, or Ice CAUTION: When you drive in mud, snow, or sand, the wheels will not get good traction. You cannot accelerate as quickly, turning is more difficult, and you will need Driving on frozen lakes, ponds, or rivers can longer braking distances.
Page 242: Driving At Night
After Off-Road Driving If the water is not too deep, drive slowly through it. At faster speeds, water splashes on the ignition system Remove any brush or debris that has collected on and your vehicle can stall. Stalling can also occur if the underbody, chassis, or under the hood.
Page 243 Here are some tips on night driving. You can be temporarily blinded by approaching headlamps. It can take a second or two, or even several • Drive defensively. seconds, for your eyes to re-adjust to the dark. When • Do not drink and drive. you are faced with severe glare, as from a driver who does not lower the high beams, or a vehicle with •...
Page 244: Driving In Rain And On Wet Roads
Driving in Rain and on Wet Roads The heavier the rain, the harder it is to see. Even if your windshield wiper blades are in good shape, a heavy rain can make it harder to see road signs and traffic signals, pavement markings, the edge of the road, and even people walking.
Page 245: Driving Through Deep Standing Water
Hydroplaning CAUTION: Hydroplaning is dangerous. So much water can build up under your tires that they can actually ride on the water. This can happen if the road is wet enough Wet brakes can cause accidents. They will not and you are going fast enough. When your vehicle work as well in a quick stop and may cause is hydroplaning, it has little or no contact with the road.
Page 246: Driving Through Flowing Water
Driving Through Flowing Water Some Other Rainy Weather Tips • Turn on your low-beam headlamps — not just your parking lamps — to help make you more CAUTION: visible to others. • Besides slowing down, allow some extra following Flowing or rushing water creates strong distance.
Page 247: City Driving
City Driving Here are ways to increase your safety in city driving: • Know the best way to get to where you are going. Get a city map and plan your trip into an unknown part of the city just as you would for a cross-country trip.
Page 248 Freeway Driving The most important advice on freeway driving is: Keep up with traffic and keep to the right. Drive at the same speed most of the other drivers are driving. Too-fast or too-slow driving breaks a smooth traffic ﬂow. Treat the left lane on a freeway as a passing lane.
Page 249: Before Leaving On A Long Trip
Once you are moving on the freeway, make certain you Is your vehicle ready for a long trip? If you keep it allow a reasonable following distance. Expect to move serviced and maintained, it is ready to go. If it needs slightly slower at night.
Page 250: Highway Hypnosis
Highway Hypnosis Hill and Mountain Roads Is there actually such a condition as highway hypnosis? Or is it just plain falling asleep at the wheel? Call it highway hypnosis, lack of awareness, or whatever. There is something about an easy stretch of road with the same scenery, along with the hum of the tires on the road, the drone of the engine, and the rush of the wind against the vehicle that can make you sleepy.
Page 251 • Keep your vehicle in good shape. Check all ﬂuid levels and also the brakes, tires, cooling system, CAUTION: and transmission. These parts can work hard on mountain roads. Coasting downhill in NEUTRAL (N) or with the ignition off is dangerous. Your brakes will have CAUTION: to do all the work of slowing down.
Page 252: Winter Driving
• Winter Driving Stay in your own lane when driving on two-lane roads in hills or mountains. Do not swing wide or cut across the center of the road. Drive at speeds that let you stay in your own lane. •...
Page 253: Driving On Snow Or Ice
Include an ice scraper, a small brush or broom, a supply of windshield washer ﬂuid, a rag, some winter outer clothing, a small shovel, a ﬂashlight, a red cloth, and reﬂective warning triangles. And, if you will be driving under severe conditions, include a small bag of sand, a piece of old carpet, or a couple of burlap bags to help provide traction.
Page 254: If You Are Caught In A Blizzard
If You Are Caught in a Blizzard Accelerate gently. Try not to break the fragile traction. If you accelerate too fast, the drive wheels will spin and If you are stopped by heavy snow, you could be in polish the surface under the tires even more. a serious situation.
Page 255 CAUTION: Snow can trap exhaust gases under your vehicle. This can cause deadly CO (carbon monoxide) gas to get inside. CO could overcome you and kill you. You cannot see it or smell it, so you might not know it is in your vehicle.
Page 256: If Your Vehicle Is Stuck In Sand, Mud, Ice Or Snow
Run your engine only as long as you must. This saves fuel. When you run the engine, make it go a CAUTION: little faster than just idle. That is, push the accelerator slightly. This uses less fuel for the heat that you get and it keeps the battery charged.
Page 257: Rocking Your Vehicle To Get It Out
Rocking Your Vehicle to Get It Out Notice: Never use recovery hooks to tow the vehicle. Your vehicle could be damaged and it would not be covered by warranty. First, turn your steering wheel left and right. That will clear the area around your front wheels. Then shift Your vehicle has recovery hooks at the front of the back and forth between REVERSE (R) and a forward vehicle.
Page 258: Loading Your Vehicle
Loading Your Vehicle Tire and Loading Information Label It is very important to know how much weight your vehicle can carry. This weight is called the vehicle capacity weight and includes the weight of all occupants, cargo, and all nonfactory-installed options. Two labels on your vehicle show how much weight it was designed to carry, the Tire and Loading Information label and the Certiﬁcation/Tire label.
Page 259: Steps For Determining Correct Load Limit
The Tire and Loading Information label also shows 4. The resulting ﬁgure equals the available amount the size of the original equipment tires (C) and the of cargo and luggage load capacity. For example, recommended cold tire inﬂation pressures (D). For more if the “XXX”...
Page 260 Example 1 Example 2 Item Description Total Item Description Total Vehicle Capacity Weight Vehicle Capacity Weight 1,000 lbs (453 kg) 1,000 lbs (453 kg) for Example 1 = for Example 2 = Subtract Occupant Subtract Occupant Weight 150 lbs 300 lbs (136 kg) Weight 150 lbs 750 lbs (136 kg) (68 kg) ×...
Page 261 Certiﬁcation/Tire Label Example 3 Item Description Total Vehicle Capacity Weight 1,000 lbs (453 kg) for Example 3 = Subtract Occupant A vehicle speciﬁc Certiﬁcation/Tire label is found on the Weight 200 lbs 1000 lbs (453 kg) (91 kg) × 5 = rear edge of the driver’s door.
Page 262 The Certiﬁcation/Tire label also tells you the maximum weights for the front and rear axles, called Gross CAUTION: Axle Weight Rating (GAWR). To ﬁnd out the actual loads on your front and rear axles, you need to go to a weigh station and weigh your vehicle.
Page 263 Two-Tiered Loading If you put things inside your vehicle — like suitcases, tools, packages, or anything else — they go as fast By positioning four 2” x 6” wooden planks across as the vehicle goes. If you have to stop or turn quickly, the width of the pickup box, you can create an upper or if there is a crash, they will keep going.
Page 264: Truck-Camper Loading Information
Add-On Equipment Truck-Camper Loading Information When you carry removable items, you may need to put Your vehicle was neither designed nor intended to carry a limit on how many people you carry inside your a slide-in type camper. vehicle. Be sure to weigh your vehicle before you buy Notice: Adding a slide-in camper or similar and install the new equipment.
Page 265: Towing
Towing Towing a Trailer Do not tow a trailer during break-in. See New Vehicle Towing Your Vehicle Break-In on page 2-15 for more information. Consult your dealer or a professional towing service if you need to have your disabled vehicle towed. See CAUTION: Roadside Assistance Program on page 7-6.
Page 266: If You Do Decide To Pull A Trailer
• Trailering is different than just driving your vehicle by Don’t tow a trailer at all during the ﬁrst 500 miles itself. Trailering means changes in acceleration, braking, (800 km) your new vehicle is driven. Your engine, handling, durability and fuel economy. Successful, axle or other parts could be damaged.
Page 267 Tow/Haul Mode Tow/Haul is designed to be most effective when the vehicle and trailer combined weight is at least 75 percent Tow/Haul is a feature that assists when pulling a heavy of the vehicle’s Gross Combined Weight Rating trailer or a large or heavy load. The purpose of the (GCWR).
Page 268: Weight Of The Trailer
Weight of the Trailer Maximum trailer weight is calculated assuming only the driver is in the tow vehicle and it has all the required How heavy can a trailer safely be? trailering equipment. The weight of additional optional equipment, passengers and cargo in the tow vehicle It depends on how you plan to use your rig.
Page 269 Weight of Trailer Tongue The tongue load (A) of any trailer is an important weight to measure because it affects the total or gross weight of your vehicle. The Gross Vehicle Weight (GVW) includes the curb weight of the vehicle, any cargo you may carry in it, and the people who will be riding in the vehicle.
Page 270 Do not exceed the maximum allowable tongue weight Consider the following example: for your vehicle. Choose the shortest hitch extension A vehicle model base weight is 5,500 lbs (2 495 kg); that will position the hitch ball closest to the vehicle. This 2,800 lbs (1 270 kg) at the front axle and 2,700 lbs will help reduce the effect of trailer tongue weight on (1 225 kg) at the rear axle.
Page 271 But let’s say your speciﬁc vehicle is equipped with The effect of tongue weight is about 1.5 times the actual some of the latest options and you have a front seat weight. Dividing the 900 lbs (408 kg) by 1.5 leaves you passenger and two rear seat passengers with some with being able to handle only 600 lbs (272 kg) of tongue luggage and gear in the vehicle as well.
Page 272 Total Weight on Your Vehicle’s Tires Weight Distributing Hitches and Weight Carrying Hitches Be sure your vehicle’s tires are inﬂated to the upper limit for cold tires. You’ll ﬁnd these numbers on the Certiﬁcation label at the rear edge of the driver’s door or see Loading Your Vehicle for more information.
Page 273: Trailer Brakes
Trailer Brakes If you will be pulling a trailer that, when loaded, will weigh more than 5,000 lbs (2 270 kg) be sure to use a If your trailer weighs more than 2,000 lbs (900 kg) properly mounted weight-distributing hitch and sway loaded, then it needs its own brakes –...
Page 274: Driving With A Trailer
Driving with a Trailer Towing a trailer requires a certain amount of experience. Before setting out for the open road, you’ll want to get to know your rig. Acquaint yourself with the feel of handling and braking with the added weight of the trailer. CAUTION: And always keep in mind that the vehicle you are driving is now a good deal longer and not nearly as...
Page 275: Following Distance
Following Distance Making Turns Stay at least twice as far behind the vehicle ahead as Notice: Making very sharp turns while trailering you would when driving your vehicle without a trailer. could cause the trailer to come in contact with the This can help you avoid situations that require vehicle.
Page 276: Driving On Grades
Driving On Grades Parking on Hills Reduce speed and shift to a lower gear before you start down a long or steep downgrade. If you don’t shift CAUTION: down, you might have to use your brakes so much that they would get hot and no longer work well. You really should not park your vehicle, with a You can tow in DRIVE (D).
Page 277: Trailer Wiring Harness
When You Are Ready to Leave After Trailer Wiring Harness Parking on a Hill 1. Apply your regular brakes and hold the pedal down while you: • start your engine, • shift into a gear, and • release the parking brake. 2.
Page 278 Electric Brake Control Jumper The eight-wire harness contains the following trailer circuits: • Yellow: Left Stop/Turn Signal CAUTION: • Dark Green: Right Stop/Turn Signal • Brown: Taillamps Be sure to use only the correct trailer brake • White: Ground harness, the one intended for use on your vehicle.
Page 279: Trailer Recommendations
Trailer Recommendations You must subtract your hitch loads from the CWR for your vehicle. Weigh your vehicle with the trailer attached, so that you won’t go over the GVWR or GAWR. If you are using a weight-distributing hitch, weigh the vehicle without the spring bars in place. You’ll get the best performance if you spread out the weight of your load the right way, and if you choose the correct hitch and trailer brakes.
Page 280 NOTES 4-64...
Page 281: Service And Appearance Care
Section 5 Service and Appearance Care Service ............5-3 Engine Fan Noise .........5-33 Accessories and Modiﬁcations ......5-3 Power Steering Fluid ........5-33 California Proposition 65 Warning .....5-3 Windshield Washer Fluid ........5-34 Doing Your Own Service Work ......5-4 Brakes ............5-35 Adding Equipment to the Outside of Battery ............5-39 Your Vehicle ..........5-4 Jump Starting ..........5-40...
Page 282 Section 5 Service and Appearance Care Tire Inspection and Rotation ......5-62 Weatherstrips ..........5-94 When It Is Time for New Tires .......5-64 Washing Your Vehicle ........5-94 Buying New Tires .........5-64 Cleaning Exterior Lamps/Lenses .....5-95 Different Size Tires and Wheels ......5-66 Finish Care ..........5-95 Uniform Tire Quality Grading ......5-66 Windshield and Wiper Blades ......5-96 Wheel Alignment and Tire Balance ....5-68...
Page 283: Service
Service Accessories and Modiﬁcations When you add non-GM accessories to your vehicle they Your dealer knows your vehicle best and wants you to can affect your vehicle’s performance and safety, be happy with it. We hope you will go to your dealer including such things as, braking, stability, ride and for all your service needs.
Page 284: Doing Your Own Service Work
Doing Your Own Service Work You should keep a record with all parts receipts and list the mileage and the date of any service work you perform. See Maintenance Record on page 6-16. CAUTION: Adding Equipment to the Outside of Your Vehicle You can be injured and your vehicle could be Things you might add to the outside of your vehicle can damaged if you try to do service work on a...
Page 285: Additives
Gasoline Speciﬁcations Additives At a minimum, gasoline should meet ASTM To provide cleaner air, all gasolines in the United States speciﬁcation D 4814 in the United States or are now required to contain additives that will help CAN/CGSB-3.5 in Canada. Some gasolines may prevent engine and fuel system deposits from forming, contain an octane-enhancing additive called allowing your emission control system to work properly.
Page 286: Fuels In Foreign Countries
Filling the Tank Notice: Your vehicle was not designed for fuel that contains methanol. Do not use fuel containing methanol. It can corrode metal parts in your fuel system and also damage the plastic and rubber CAUTION: parts. That damage would not be covered under your warranty.
Page 287 The TIGHTEN FUEL CAP message will be displayed on the Driver Information Center (DIC) if the fuel cap is CAUTION: not properly installed. See DIC Warnings and Messages on page 3-47 for more information. If you spill fuel and then something ignites it, you could be badly burned.
Page 288: Filling A Portable Fuel Container
Filling a Portable Fuel Container Checking Things Under the Hood CAUTION: CAUTION: Never ﬁll a portable fuel container while it is in your vehicle. Static electricity discharge from An electric fan under the hood can start up the container can ignite the gasoline vapor. and injure you even when the engine is not You can be badly burned and your vehicle running.
Page 289: Hood Release
Hood Release To open the hood do the following: 1. Pull the handle with this symbol on it. It is located inside the vehicle to the lower left of the steering wheel. 2. Then go to the front of the vehicle and pull up on the secondary hood release located near the center of the grille.
Page 290: Engine Compartment Overview
Engine Compartment Overview When you lift the hood on the VORTEC™ 6000 V8 engine, here is what you will see: 5-10...
Page 291 A. Engine Air Cleaner/Filter. See Engine Air H. Remote Negative (−) Terminal (GND). See Jump Cleaner/Filter on page 5-17. Starting on page 5-40. B. Coolant Surge Tank and Pressure Cap. See Cooling I. Remote Positive (+) Terminal. See Jump Starting on System on page 5-28 and Coolant Surge Tank page 5-40.
Page 292: Engine Oil
Engine Oil The engine oil dipstick handle is a yellow loop. See Engine Compartment Overview on page 5-10 for the location of the engine oil dipstick. If the CHECK OIL LEVEL message appears on the Driver Information Center (DIC), it means you need to 1.
Page 293: When To Add Engine Oil
When to Add Engine Oil See Engine Compartment Overview on page 5-10 for the location of the engine oil ﬁll cap. If the oil is below the cross-hatched area at the tip of the dipstick, you will need to add at least one quart/liter of oil.
Page 294: What Kind Of Engine Oil To Use
What Kind of Engine Oil to Use • SAE 5W-30 As shown in the viscosity chart, SAE 5W-30 is best for your vehicle. These numbers on an oil container show its viscosity, or thickness. Do not use other viscosity oils such as SAE 20W-50. Oils meeting these requirements should also have the starburst...
Page 295: Engine Oil Additives
® GM Goodwrench oil meets all the requirements for When the system has calculated that oil life has been your vehicle. diminished, it will indicate that an oil change is necessary. A CHANGE ENGINE OIL message will If you are in an area of extreme cold, where come on.
Page 296: How To Reset The Engine Oil Life System
How to Reset the Engine Oil Life What to Do with Used Oil System Used engine oil contains certain elements that may be unhealthy for your skin and could even cause cancer. The Engine Oil Life System calculates when to Do not let used oil stay on your skin for very long.
Page 297: Engine Air Cleaner/Filter
Engine Air Cleaner/Filter When to Inspect the Engine Air Cleaner/Filter See Engine Compartment If your vehicle is equipped with an air ﬁlter restriction Overview on page 5-10 for indicator, it lets you know when the engine air the location of the engine cleaner/ﬁlter needs to be replaced.
Page 298 How to Inspect the Engine Air Replacing the Engine Air Cleaner/Filter and Resetting the Air Filter Restriction Cleaner/Filter Indicator Vehicles With an Air Filter Restriction Indicator Locate the air ﬁlter restriction indicator on the engine air cleaner/ﬁlter cover. When the indicator turns black or is in the red/orange “change”...
Page 299: Automatic Transmission Fluid
CAUTION: Operating the engine with the air cleaner/ﬁlter off can cause you or others to be burned. The air cleaner not only cleans the air; it helps to stop ﬂames if the engine backﬁres. If it is not there and the engine backﬁres, you could be burned.
Page 300: How To Check Automatic Transmission Fluid
How to Check Automatic Get the vehicle warmed up by driving about 15 miles (24 km) when outside temperatures are above Transmission Fluid 50°F (10°C). If it is colder than 50°F (10°C), drive the vehicle in THIRD (3) until the engine temperature Because this operation can be a little difficult, you may gage moves and then remains steady for 10 minutes.
Page 301 Then, without shutting off the engine, follow these steps: The transmission dipstick handle is located at the rear of the engine compartment, on the passenger’s side of the vehicle. See Engine Compartment Overview on page 5-10 for further information on location. 3.
Page 302: Engine Coolant
Consistency of Readings Notice: Use of the incorrect automatic transmission ﬂuid may damage your vehicle, and the damages Always check the ﬂuid level at least twice using the may not be covered by your warranty. Always procedure described previously. Consistency (repeatable use the automatic transmission ﬂuid listed in readings) is important to maintaining proper ﬂuid level.
Page 303: What To Use
What to Use A 50/50 mixture of clean, drinkable water and ® DEX-COOL coolant will: Use a mixture of one-half clean, drinkable water and Give freezing protection down to −34°F (−37°C). • ® one-half DEX-COOL coolant which will not damage •...
Page 304: Checking Coolant
If you have to add coolant more than four times a year, have your dealer check your cooling system. CAUTION: Notice: If you use extra inhibitors and/or additives in your vehicle’s cooling system, you could Turning the surge tank pressure cap when the damage your vehicle.
Page 305: Adding Coolant
Adding Coolant Coolant Surge Tank Pressure Cap ® If you need more coolant, add the proper DEX-COOL Notice: If the pressure cap is not tightly installed, coolant mixture at the surge tank, but only when the coolant loss and possible engine damage may occur. engine is cool.
Page 306: If Steam Is Coming From Your Engine
If Steam Is Coming From Your Engine CAUTION: (Continued) CAUTION: If you keep driving when your engine is overheated, the liquids in it can catch ﬁre. You or others could be badly burned. Stop Steam from an overheated engine can burn your engine if it overheats, and get out of the you badly, even if you just open the hood.
Page 307: If No Steam Is Coming From Your Engine
If No Steam Is Coming From Your If you no longer have the overheat warning, you can drive. Just to be safe, drive slower for about 10 minutes. Engine If the warning does not come back on, you can drive normally.
Page 308: Overheated Engine Protection Operating Mode
Overheated Engine Protection Cooling System Operating Mode When you decide it is safe to lift the hood, here is what you will see: If an overheated engine condition exists and the REDUCED ENGINE POWER message is displayed, an overheat protection mode which alternates ﬁring groups of cylinders helps prevent engine damage.
Page 309 The coolant level should be at or above the FULL CAUTION: COLD mark. If it is not, you may have a leak at the pressure cap or in the An electric fan under the hood can start up radiator hoses, heater and injure you even when the engine is not hoses, radiator, water running.
Page 310: How To Add Coolant To The Coolant Surge Tank
How to Add Coolant to the Coolant If your vehicle is equipped with an electric engine cooling fan, check the coolant temperature gage. If the Surge Tank coolant temperature is approximately 232°F (111°C), the electric cooling fan should be running. If it is If you have not found a problem yet, check to see if not, your vehicle needs service.
Page 311 CAUTION: CAUTION: Adding only plain water to your cooling You can be burned if you spill coolant on hot system can be dangerous. Plain water, engine parts. Coolant contains ethylene glycol or some other liquid such as alcohol, can boil and it will burn if the engine parts are hot before the proper coolant mixture will.
Page 312 3. Fill the coolant surge tank with the proper mixture, 4. With the coolant surge tank pressure cap off, start to the FULL COLD mark. the engine and let it run until you can feel the upper radiator hose getting hot. Watch out for the engine cooling fan.
Page 313: Engine Fan Noise
Engine Fan Noise Power Steering Fluid If your vehicle is equipped with a clutched engine See Engine Compartment cooling fan, when the clutch is engaged, the fan spins Overview on page 5-10 for faster to provide more air to cool the engine. In most reservoir location.
Page 314: Windshield Washer Fluid
How to Check Power Steering Fluid Windshield Washer Fluid To check the power steering ﬂuid, do the following: What to Use 1. Turn the key off and let the engine compartment When you need windshield washer ﬂuid, be sure to cool down.
Page 315: Brakes
Brakes Open the cap with the washer symbol on it. Add washer ﬂuid until the Brake Fluid tank is full. See Engine Compartment Overview on Your brake master cylinder page 5-10 for reservoir reservoir is ﬁlled with location. DOT-3 brake ﬂuid. See Engine Compartment Overview on page 5-10 for the location of the...
Page 316: Checking Brake Fluid
Checking Brake Fluid So, it is not a good idea to top off your brake ﬂuid. Adding brake ﬂuid will not correct a leak. If you add ﬂuid You can check the brake ﬂuid without taking off the cap. when your linings are worn, then you will have too much ﬂuid when you get new brake linings.
Page 317 What to Add Notice: • Using the wrong ﬂuid can badly damage brake When you do need brake ﬂuid, use only DOT-3 brake system parts. For example, just a few drops of ﬂuid. Use new brake ﬂuid from a sealed container mineral-based oil, such as engine oil, in your only.
Page 318: Brake Adjustment
Brake Wear Some driving conditions or climates may cause a brake squeal when the brakes are ﬁrst applied or lightly Your vehicle has four-wheel disc brakes. applied. This does not mean something is wrong with your brakes. Disc brake pads have built-in wear indicators that make a high-pitched warning sound when the brake pads are Properly torqued wheel nuts are necessary to help worn and new pads are needed.
Page 319: Battery
Replacing Brake System Parts Warning: Battery posts, terminals, and related accessories contain lead and lead compounds, The braking system on a vehicle is complex. Its many chemicals known to the State of California to cause parts have to be of top quality and work well together cancer and reproductive harm.
Page 320: Jump Starting
Jump Starting 1. Check the other vehicle. It must have a 12-volt battery with a negative ground system. If your vehicle’s battery (or batteries) has run down, you Notice: If the other vehicle’s system is not a 12-volt may want to use another vehicle and some jumper system with a negative ground, both vehicles can cables to start your vehicle.
Page 321 4. Open the hood on the other vehicle and locate the positive (+) and negative (−) terminal locations. CAUTION: Your vehicle has a remote positive (+) jump starting terminal and a remote negative (−) jump starting terminal. You should always use these remote Using a match near a battery can cause battery terminals instead of the terminals on the battery.
Page 322 6. Connect the red positive (+) cable to the CAUTION: positive (+) terminal of the vehicle with the dead battery. Use Fans or other moving engine parts can injure a remote positive (+) you badly. Keep your hands away from moving terminal if the parts once the engine is running.
Page 323 9. Connect the other end of the negative (−) cable to the remote negative (−) terminal, marked GND, on the vehicle with the dead battery. 10. Now start the vehicle with the good battery and run Jumper Cable Removal the engine for a while. A.
Page 324: All-Wheel Drive
How to Check Lubricant To disconnect the jumper cables from both vehicles do the following: 1. Disconnect the black negative (−) cable from the vehicle that had the bad battery. 2. Disconnect the black negative (−) cable from vehicle with the good battery. 3.
Page 325: Rear Axle
Rear Axle How to Check Lubricant When to Check Lubricant It is not necessary to regularly check rear axle ﬂuid unless you suspect there is a leak or you hear an unusual noise. A ﬂuid loss could indicate a problem. Have it inspected and repaired.
Page 326: Front Axle
Front Axle If the level is below the bottom of the ﬁller plug hole, you may need to add some lubricant: When to Check Lubricant • When the differential is cold, add enough lubricant to raise the level to 0 to 3/8 inch (9.5 mm) below It is not necessary to regularly check front axle ﬂuid the ﬁller plug hole.
Page 327: Bulb Replacement
Bulb Replacement Headlamps To replace a headlamp bulb, do the following: For the proper type of replacement bulbs, see Replacement Bulbs on page 5-52. 1. Open the hood. See Hood Release on page 5-9 for more information. For any bulb changing procedure not listed in this section, contact your dealer.
Page 328: Front Turn Signal, Sidemarker And Daytime Running Lamps
Front Turn Signal, Sidemarker and Daytime Running Lamps A. Low-Beam Headlamp B. High-Beam Headlamp 3. Pull the headlamp assembly out. A. Sidemarker Lamp 4. Unplug the electrical connector. B. Retainer Clip 5. Turn the old bulb counterclockwise and remove it C.
Page 329 5. Press the locking release lever, turn the bulb socket counterclockwise and remove it from the turn signal assembly. 6. Remove the old bulb from the bulb socket. 7. Install a new bulb into the bulb socket. 8. Insert the bulb socket into the turn signal assembly and turn it clockwise until it locks.
Page 330: Center High-Mounted Stoplamp (Chmsl)
Center High-Mounted Stoplamp (CHMSL) and Cargo Lamp To replace one of these bulbs, do the following: A. Cargo Lamp B. Center High-Mounted Stoplamp Bulb 1. Remove the screws and lift off the lamp assembly. 2. Remove the back plate from the assembly by pressing the release tabs.
Page 331: Taillamps, Turn Signal, Stoplamps And Back-Up Lamps
4. If a CHMSL bulb is replaced, put the new bulb into 2. Remove the the socket and press it in until it is tight. two taillamp assembly screws near the If a cargo lamp is replaced, put a new cargo lamp tailgate latch.
Page 332: Windshield Wiper Blade Replacement
Replacement Bulbs Exterior Lamp Bulb Number Back-up, Front and Rear Turn 3157 Signal, Taillamp and Stoplamps Cargo Lamps and Center High-Mounted Stoplamp (CHMSL) Daytime Running Lamps (DRL) 4114K Headlamps High-Beam 9005 9005 or Low-Beam 9005 LL (Long Life) For replacement bulbs not listed here, contact your dealer.
Page 333 To replace the windshield wiper blade assembly do the 2. Push the release lever (B) to disengage the hook following: and push the wiper arm (A) out of the blade (C). 1. Lift the wiper arm away from the windshield. 3.
Page 334: Tires
Tires CAUTION: (Continued) Your new vehicle comes with high-quality tires made by a leading tire manufacturer. If you ever have questions • Overinﬂated tires are more likely to be cut, about your tire warranty and where to obtain service, punctured, or broken by a sudden see your GM Warranty booklet for details.
Page 335: Tire Sidewall Labeling
Tire Sidewall Labeling (B) TPC Spec (Tire Performance Criteria Speciﬁcation): Original equipment tires designed to GM’s speciﬁc tire performance criteria have a Useful information about a tire is molded into the TPC speciﬁcation code molded onto the sidewall. sidewall. The following illustrations are examples of a GM’s TPC speciﬁcations meet or exceed all federal typical P-Metric and a LT-Metric tire sidewall.
Page 336 (C) Dual Tire Maximum Load: Maximum load that can be carried and the maximum pressure needed to support that load when used in a dual conﬁguration. For information on recommended tire pressure see Inﬂation - Tire Pressure on page 5-61 and Loading Your Vehicle on page 4-42.
Page 337: Tire Size
Tire Size (A) Light Truck (LT-Metric) Tire: The United States version of a metric tire sizing system. The letters LT as The following examples show the different parts of a the ﬁrst two characters in the tire size means a light tire size.
Page 338: Tire Terminology And Deﬁnitions
Tire Terminology and Deﬁnitions Bias Ply Tire: A pneumatic tire in which the plies are laid at alternate angles less than 90 degrees to the centerline of the tread. Air Pressure: The amount of air inside the tire pressing outward on each square inch of the tire. Air pressure Cold Inﬂation Pressure: The amount of air pressure is expressed in pounds per square inch (psi) or in a tire, measured in pounds per square inch (psi)
Page 339 GVWR: Gross Vehicle Weight Rating, see Loading Maximum Load Rating: The load rating for a tire at Your Vehicle on page 4-42. the maximum permissible inﬂation pressure for that tire. GAWR FRT: Gross Axle Weight Rating for the front Maximum Loaded Vehicle Weight: The sum of axle, see Loading Your Vehicle on page 4-42.
Page 340 Recommended Inﬂation Pressure: Vehicle UTQGS (Uniform Tire Quality Grading Standards): manufacturer’s recommended tire inﬂation pressure and A tire information system that provides consumers with shown on the tire placard. See Inﬂation - Tire Pressure ratings for a tire’s traction, temperature, and treadwear. on page 5-61 and Loading Your Vehicle on page 4-42.
Page 341: Inﬂation - Tire Pressure
Inﬂation - Tire Pressure A Tire and Loading Information label is attached to the vehicle’s center pillar (B-pillar), below the driver’s door lock post (striker). This label lists your vehicle’s Tires need the correct amount of air pressure to operate original equipment tires and their recommended cold effectively.
Page 342: How To Check
How to Check Tire Inspection and Rotation Use a good quality pocket-type gage to check tire Tires should be rotated every 5,000 to 8,000 miles pressure. You cannot tell if your tires are properly (8 000 to 13 000 km). inﬂated simply by looking at them.
Page 343 CAUTION: Rust or dirt on a wheel, or on the parts to which it is fastened, can make wheel nuts become loose after a time. The wheel could come off and cause an accident. When you change a wheel, remove any rust or dirt from places where the wheel attaches to the vehicle.
Page 344: When It Is Time For New Tires
When It Is Time for New Tires Buying New Tires GM has developed and matched speciﬁc tires for your One way to tell when it is vehicle. The original equipment tires installed on time for new tires is to your vehicle, when it was new, were designed to meet check the treadwear General Motors Tire Performance Criteria Speciﬁcation indicators, which will...
Page 345 CAUTION: CAUTION: Mixing tires could cause you to lose control If you use bias-ply tires on your vehicle, the while driving. If you mix tires of different sizes, wheel rim ﬂanges could develop cracks after brands or types (radial and bias-belted tires), many miles of driving.
Page 346: Different Size Tires And Wheels
Different Size Tires and Wheels Uniform Tire Quality Grading If you add wheels or tires that are a different size than Quality grades can be found where applicable on the your original equipment wheels and tires, this may tire sidewall between tread shoulder and maximum affect the way your vehicle performs, including its section width.
Page 347 Treadwear Temperature – A, B, C The treadwear grade is a comparative rating based on The temperature grades are A (the highest), B, and C, the wear rate of the tire when tested under controlled representing the tire’s resistance to the generation conditions on a speciﬁed government test course.
Page 348: Wheel Replacement
Wheel Alignment and Tire Balance If you need to replace any of your wheels, wheel bolts or wheel nuts, replace them only with new GM original equipment parts. This way, you will be The tires and wheels on your vehicle were aligned sure to have the right wheel, wheel bolts and wheel nuts and balanced carefully at the factory to give you the for your vehicle.
Page 349: Tire Chains
Used Replacement Wheels Tire Chains CAUTION: CAUTION: Putting a used wheel on your vehicle is Do not use tire chains. There is not enough dangerous. You cannot know how it has been clearance. Tire chains used on a vehicle used or how far it has been driven. It could fail without the proper amount of clearance can suddenly and cause a crash.
Page 350: If A Tire Goes Flat
If a Tire Goes Flat CAUTION: It is unusual for a tire to blowout while you are driving, especially if you maintain your vehicle’s tires properly. If air goes out of a tire, it is much more likely to leak out Lifting a vehicle and getting under it to do slowly.
Page 351 When your vehicle has a ﬂat tire, use the following example as a guide to assist you in the placement of CAUTION: wheel blocks. Changing a tire can be dangerous. The vehicle can slip off the jack and roll over or fall on you or other people.
Page 352: Removing The Spare Tire And Tools
Removing the Spare Tire and Tools The equipment you will need is located under the passenger’s side second row seat. The spare tire is located underneath the vehicle. 1. Pull up the second row seat with the loop at the base of the seat cushion to access the tools.
Page 353 1. Open the spare tire lock cover on the bumper and use the ignition key to remove the lock if your vehicle is equipped with a spare tire lock (J). 2. Assemble the wheel wrench (H) and the two jack handle extensions (I) as shown.
Page 354 3. Insert the hoist end 4. Turn the wheel wrench (H) counterclockwise to (open end) (F) of the lower the spare tire to the ground. Continue to extension through turn the wheel wrench until the spare tire can be the hole (G) in the rear pulled out from under the vehicle.
Page 355: Removing The Flat Tire And Installing The Spare Tire
Removing the Flat Tire and 6. Tilt the retainer at the end of the cable when Installing the Spare Tire the tire has been lowered, so it can be Use the following pictures and instructions to remove pulled up through the ﬂat tire and raise the vehicle.
Page 356 1. Remove the center cap by placing the chisel end of 2. Use the wheel wrench to loosen all the wheel nuts. the wheel wrench in the slot on the wheel and Turn the wheel wrench counterclockwise to loosen gently prying the cap out. the wheel nuts.
Page 357 CAUTION: Getting under a vehicle when it is jacked up is dangerous. If the vehicle slips off the jack you could be badly injured or killed. Never get under a vehicle when it is supported only by a jack. Jack Positions (Overall View) A: Front Location B: Rear Location 5-77...
Page 358 CAUTION: Raising your vehicle with the jack improperly positioned can damage the vehicle and even make the vehicle fall. To help avoid personal injury and vehicle damage, be sure to ﬁt the jack lift head into the proper location before raising the vehicle.
Page 359 4. Remove all the wheel nuts and take off the ﬂat tire. Rear Position 5-79...
Page 360 CAUTION: CAUTION: Rust or dirt on the wheel, or on the parts to Never use oil or grease on studs or nuts. which it is fastened, can make the wheel nuts If you do, the nuts might come loose. Your become loose after a time.
Page 361 Front Position Rear Position 5-81...
Page 362 8. Tighten the nuts ﬁrmly in a crisscross CAUTION: sequence as shown by turning the wheel wrench clockwise. Incorrect wheel nuts or improperly tightened wheel nuts can cause the wheel to come loose and even come off. This could lead to an accident.
Page 363: Secondary Latch System
Secondary Latch System To release the spare tire from the secondary latch, do the following: Your vehicle has an underbody-mounted tire hoist assembly equipped with a secondary latch system. It is designed to stop the spare tire from suddenly falling off your vehicle.
Page 364 3. Loosen the cable by turning the wheel wrench counterclockwise three or four turns. 4. Repeat this procedure at least two times. If the spare tire lowers to the ground, continue with Step 5 of Removing the Spare Tire and Tools on page 5-72.
Page 365 12. Lower the jack by turning the wheel wrench counterclockwise. Keep lowering the jack until the spare tire slides off the jack or is hanging by the cable. CAUTION: Someone standing too close during the procedure could be injured by the jack. If the spare tire does not slide off the jack completely, make sure no one is behind you or on either side of you as you pull the jack out...
Page 366: Storing A Flat Or Spare Tire And Tools
Storing a Flat or Spare Tire 15. Tilt the retainer at the end of the cable and and Tools pull it through the wheel opening. Pull the tire out from under the vehicle. CAUTION: Storing a jack, a tire, or other equipment in the passenger compartment of the vehicle could cause injury.
Page 367 Store the tire under the rear of the vehicle in the spare tire 1. Put the tire on the ground at the rear of the vehicle carrier. Use the following art and text to assist you: with the valve stem pointed down, and to the rear. 2.
Page 368 4. Insert the hoist end (F) through the hole (G) in the rear bumper and into the hoist shaft. 5. Raise the tire part way upward. Make sure the retainer is seated in the wheel opening. 6. Raise the tire fully against the underside of the vehicle by turning the wheel wrench clockwise 7.
Page 369 To store the jack and jack tools, do the following: 1. Put the tools (D) in the tool bag (E) and place them in the retaining bracket (C). 2. Tighten down the wing nut (C). 3. Assemble the wheel blocks (B) and jack (G) together with the wing nut (A) and retaining hook (H).
Page 370: Appearance Care
Spare Tire Appearance Care Your vehicle, when new, had a fully-inﬂated spare tire. Cleaning the Inside of Your Vehicle A spare tire may lose air over time, so check its inﬂation pressure regularly. See Inﬂation - Tire Pressure Your vehicle’s interior will continue to look its best if on page 5-61 and Loading Your Vehicle on page 4-42 it is cleaned often.
Page 371 When cleaning your vehicle’s interior, only use cleaners Do not clean your vehicle using the following cleaners speciﬁcally designed for the surfaces being cleaned. or techniques: Permanent damage may result from using cleaners on • Never use a knife or any other sharp object to surfaces for which they were not intended.
Page 372 Fabric/Carpet 4. Continue to gently rub the soiled area until the cleaning cloth remains clean. Use a vacuum cleaner with a soft brush attachment 5. If the soil is not completely removed, use a mild frequently to remove dust and loose dirt. A canister soap solution and repeat the cleaning process vacuum with a beater bar in the nozzle may only that was used with plain water.
Page 373: Leather
Leather Instrument Panel, Vinyl, and Other Plastic Surfaces A soft cloth dampened with water may be used to remove dust. If a more thorough cleaning is necessary, A soft cloth dampened with water may be used to a soft cloth dampened with a mild soap solution can remove dust.
Page 374: Wood Panels
Wood Panels Washing Your Vehicle Use a clean cloth moistened in warm, soapy water The paint ﬁnish on the vehicle provides beauty, depth of (use mild dish washing soap). Dry the wood immediately color, gloss retention, and durability. with a clean cloth. The best way to preserve the vehicle’s ﬁnish is to keep it clean by washing it often with lukewarm or cold water.
Page 375: Cleaning Exterior Lamps/Lenses
Cleaning Exterior Lamps/Lenses Foreign materials such as calcium chloride and other salts, ice melting agents, road oil and tar, tree sap, bird droppings, chemicals from industrial chimneys, etc., Use only lukewarm or cold water, a soft cloth and a car can damage your vehicle’s ﬁnish if they remain washing soap to clean exterior lamps and lenses.
Page 376: Windshield And Wiper Blades
Windshield and Wiper Blades Aluminum or Chrome-Plated Wheels If the windshield is not clear after using the windshield The vehicle may be equipped with either aluminum or washer, or if the wiper blade chatters when running, chrome-plated wheels. wax, sap, or other material may be on the blade Keep the wheels clean using a soft clean cloth with mild or windshield.
Page 377: Tires
Tires Notice: Using chrome polish on aluminum wheels could damage the wheels. The repairs would not be covered by your warranty. Use chrome polish on To clean the tires, use a stiff brush with tire cleaner. chrome wheels only. Notice: Using petroleum-based tire dressing Use chrome polish only on chrome-plated wheels, but products on your vehicle may damage the paint avoid any painted surface of the wheel, and buff off...
Page 378: Chemical Paint Spotting
Finish Damage Chemical Paint Spotting Any stone chips, fractures or deep scratches in the Some weather and atmospheric conditions can create ﬁnish should be repaired right away. Bare metal a chemical fallout. Airborne pollutants can fall upon and will corrode quickly and may develop into major repair attack painted surfaces on the vehicle.
Page 379: Vehicle Care/Appearance Materials
Vehicle Care/Appearance Materials Description Usage Removes light scratches Description Usage Cleaner Wax and protects ﬁnish. Polishing Cloth Interior and exterior Cleans, shines, and Wax-Treated polishing cloth. Foaming Tire Shine protects in one step. Low Gloss Tar and Road Oil Removes tar, road oil, No wiping necessary.
Page 380: Vehicle Identiﬁcation Number (Vin)
Vehicle Identiﬁcation Engine Identiﬁcation The eighth character in the VIN is the engine code. This code will help you identify your vehicle’s engine, Vehicle Identiﬁcation Number (VIN) speciﬁcations, and replacement parts. Service Parts Identiﬁcation Label You will ﬁnd this label on the inside of the glove box. It is very helpful if you ever need to order parts.
Page 381: Electrical System
Electrical System Power Windows and Other Power Options Add-On Electrical Equipment Circuit breakers protect the power windows and other power accessories. When the current load is too heavy, Notice: Don’t add anything electrical to your the circuit breaker opens and closes, protecting the vehicle unless you check with your dealer ﬁrst.
Page 382: Instrument Panel Fuse Block
Instrument Panel Fuse Block The fuse block access door is on the driver’s side edge of the instrument panel. Pull off the cover to access the fuse block. To remove fuses, hold the end of the fuse between your thumb and index ﬁnger and pull straight out. Fuses Usage You may have spare fuses located behind the fuse...
Page 383 Fuses Usage Fuses Usage HTR/AC Climate Control System Vehicle Stoplamps, Brake VEH STOP Module, Electronic Throttle Power Door Lock Relay LCK (Relay) Control Module (Lock Function) RT TRLR ST/TRN Right Turn Signal/Stop Trailer HVAC 1 Climate Control System Right Turn Signals and Driver’s Door Harness RT TRN LT DR...
Page 384: Center Instrument Panel Fuse Block
Center Instrument Panel Fuse Block Device Usage HDLR 2 Headliner Wiring Connector The center instrument panel utility block is located BODY Body Wiring Connector underneath the instrument panel, to the left of the DEFOG Rear Defogger Relay steering column. HDLNR 1 Headliner Wiring Connector 1 SPARE RELAY Not Used...
Page 385: Underhood Fuse Block
Underhood Fuse Block The underhood fuse block in the engine compartment on the driver’s side of the vehicle near the battery. Lift the cover for access to the fuse/relay block. To remove fuses hold the end of the fuse between your thumb and index ﬁnger and pull straight out.
Page 386 5-106...
Page 387 *1 — Gasoline Engine and Fuel Injection Rail #2. Fuses Usage *2 — Gasoline Engine and Fuel Injection Rail #1. Accessory Power/Trailer STUD #2* Wiring Brake Feed *3 — Gasoline Engine; Oxygen Sensors. Anti-lock Brakes *4 — Gasoline Engine; Oxygen Sensors. VSES/ECAS Vehicle Stability *5 —...
Page 388 Fuses Usage Fuses Usage Electronic Throttle Control, LH HID Not Used ETC/ECM Electronic Brake Controller Daytime Running Lamps Instrument Panel Cluster, Regulated Voltage Control Air Conditioning Relay, IGN E Instrument Panel Cluster/ Turn Signal/Hazard Switch, IPC/DIC Driver Information Center Starter Relay HVAC/ECAS Climate Control Controller Ride Control...
Page 389 Fuses Usage Auxiliary Electric Cooling Fan Fuse CRNK Starting System Block LO HDLP-RT Headlamp Low Beam-Right FOG LP Fog Lamps Relay The auxiliary electric FOG LP Fog Lamps cooling fan fuse block is located in the engine HORN Horn Relay compartment on the Windshield Washer W/S WASH...
Page 390: Capacities And Speciﬁcations
Capacities and Speciﬁcations The following approximate capacities are given in English and metric conversions. See Recommended Fluids and Lubricants on page 6-13. Capacities and Speciﬁcations Capacities Application English Metric Cooling System Engine Driven Fan 16.2 quarts 15.3 L Electric Engine Cooling Fan 16.6 quarts 15.7 L Engine Oil with Filter...
Page 391 Section 6 Maintenance Schedule Maintenance Schedule ........6-2 Owner Checks and Services ......6-9 Introduction ...........6-2 At Each Fuel Fill ..........6-9 Maintenance Requirements ......6-2 At Least Once a Month .........6-10 Your Vehicle and the Environment ....6-2 At Least Once a Year ........6-10 Using the Maintenance Schedule ......6-2 Recommended Fluids and Lubricants ....6-13 Scheduled Maintenance ........6-4...
Page 392: Maintenance Schedule
Maintenance Schedule Your Vehicle and the Environment Proper vehicle maintenance not only helps to keep Introduction your vehicle in good working condition, but also helps the environment. All recommended maintenance is Important: Keep engine oil at the proper level and important.
Page 393 This schedule is for vehicles that: • carry passengers and cargo within recommended CAUTION: limits. You will ﬁnd these limits on the tire and loading information label. See Loading Your Vehicle Performing maintenance work on a vehicle on page 4-42. can be dangerous.
Page 394: Scheduled Maintenance
Owner Checks and Services on page 6-9 tells you what If the engine oil life system is ever reset accidentally, should be checked, when to check it, and what you you must service your vehicle within 3,000 miles can easily do to help keep your vehicle in good (5 000 km) since your last service.
Page 395 Scheduled Maintenance Service Maintenance I Maintenance II Change engine oil and ﬁlter. See Engine Oil on page 5-12. Reset oil life system. • • See Engine Oil Life System on page 5-15. An Emission Control Service. • • Lubricate chassis components. See footnote #. •...
Page 396: Additional Required Services
Additional Required Services The following services should be performed at the ﬁrst maintenance service (I or II) after the indicated miles (kilometers) shown for each item. Additional Required Services 25,000 50,000 75,000 100,000 125,000 150,000 Service and Miles (Kilometers) (41 500) (83 000) (125 000) (166 000)
Page 397: Maintenance Footnotes
Additional Required Services (cont’d) 25,000 50,000 75,000 100,000 125,000 150,000 Service and Miles (Kilometers) (41 500) (83 000) (125 000) (166 000) (207 500) (240 000) Replace spark plugs and inspect • spark plug wires. An Emission Control Service. Engine cooling system service (or every ﬁve years, whichever occurs ﬁrst).
Page 398 (b) Visually inspect front and rear suspension and (f) Lubricate all key lock cylinders, hood latch assembly, steering system for damaged, loose, or missing parts, secondary latch, pivots, spring anchor, release pawl, signs of wear, or lack of lubrication. Inspect power door hinges, liftgate hinge, liftgate linkage, liftgate handle steering lines and hoses for proper hook-up, binding, pivot points, latch bolt, fuel door hinge, locks, and...
Page 399: Engine Oil Level Check
At Each Fuel Fill (i) Drain, ﬂush, and reﬁll cooling system. This service can be complex; you should have your dealer perform this service. See Engine Coolant on page 5-22 for It is important to perform these underhood checks at what to use.
Page 400: At Least Once A Month
At Least Once a Month At Least Once a Year Tire Inﬂation Check Starter Switch Check Visually inspect your vehicle’s tires and make sure they are inﬂated to the correct pressures. Do not forget to CAUTION: check the spare tire. See Tires on page 5-54 for further details.
Page 401: Ignition Transmission Lock Check
Automatic Transmission Shift Lock 3. With the engine off, turn the ignition to RUN, but do not start the engine. Without applying the regular Control System Check brake, try to move the shift lever out of PARK (P) with normal effort. If the shift lever moves out ®...
Page 402: Underbody Flushing Service
Parking Brake and Automatic Park on a fairly steep hill, with the vehicle facing downhill. Keeping your foot on the regular brake, set the Transmission Park (P) Mechanism Check parking brake. • To check the parking brake’s holding ability: With CAUTION: the engine running and transmission in NEUTRAL (N), slowly remove foot pressure from...
Page 403: Recommended Fluids And Lubricants
Recommended Fluids and Usage Fluid/Lubricant Lubricants GM Power Steering Fluid Power Steering (GM Part No. U.S. 89021184, in System Canada 89021186). Fluids and lubricants identiﬁed below by name, part ® Automatic DEXRON -VI Automatic number, or speciﬁcation may be obtained from Transmission Transmission Fluid.
Page 404 Usage Fluid/Lubricant Usage Fluid/Lubricant ® DEXRON -III Automatic Body Door Transmission Fluid. Look for Hinge Pins, Transfer Case “Approved for the H-Speciﬁcation” Tailgate Hinge Multi-Purpose Lubricant, Superlube on the label. and Linkage, (GM Part No. U.S. 12346241, in Folding Seats, Canada 10953474).
Page 405: Normal Maintenance Replacement Parts
Normal Maintenance Replacement Parts Replacement parts listed below by name, part number or speciﬁcation can be obtained from your GM dealer. ® Part GM Part Number ACDelco Part Number Engine Air Cleaner/Filter 1038768 A1518C Oil Filter 88984215 PF46 Spark Plugs 12571164 41-985 Windshield Wiper Blades...
Page 406: Maintenance Record
Maintenance Record After the scheduled services are performed, record the date, odometer reading, who performed the service, and the type of services performed in the boxes provided. See Maintenance Requirements on page 6-2. Any additional information from Owner Checks and Services on page 6-9 can be added on the following record pages. You should retain all maintenance receipts.
Page 407 Maintenance Record (cont’d) Odometer Maintenance I or Date Serviced By Services Performed Reading Maintenance II 6-17...
Page 408 Maintenance Record (cont’d) Odometer Maintenance I or Date Serviced By Services Performed Reading Maintenance II 6-18...
Page 409: Customer Assistance And Information
Section 7 Customer Assistance and Information Customer Assistance and Information ....7-2 Reporting Safety Defects ........7-14 Customer Satisfaction Procedure ......7-2 Reporting Safety Defects to the Online Owner Center ........7-3 United States Government ......7-14 Customer Assistance for Text Reporting Safety Defects to the Telephone (TTY) Users ........7-4 Canadian Government ........7-15 Customer Assistance Offices ......7-4...
Page 410: Customer Assistance And Information
Your satisfaction and goodwill are important to visible through the windshield. your dealer and to GMC. Normally, any concerns with the sales transaction or the operation of the vehicle •...
Page 411: Online Owner Center
Online Owner Center The BBB Auto Line Program is an out of court program administered by the Council of Better Business Bureaus to settle automotive disputes regarding vehicle repairs The Owner Center is a resource for your GM ownership or the interpretation of the New Vehicle Limited needs.
Page 412: Customer Assistance For Text Telephone (Tty) Users
GMC encourages customers to call the toll-free number 1-800-263-7854 (French) for assistance. However, if a customer wishes to 1-800-263-3830 (For Text Telephone devices (TTYs)) write or e-mail GMC, refer to the addresses below. Roadside Assistance: 1-800-268-6800 United States GMC Customer Assistance Center P.O.
Page 413: Gm Mobility Reimbursement Program
All Overseas Locations GM Mobility Reimbursement Program Please contact the local General Motors Business Unit. Mexico, Central America and Caribbean Islands/Countries (Except Puerto Rico and U.S. Virgin Islands) General Motors de Mexico, S. de R.L. de C.V. Customer Assistance Center Paseo de la Reforma # 2740 Col.
Page 414: Roadside Assistance Program
Flat Tire Change: Installation of a spare tire will be covered at no charge. The customer is responsible As the owner of a new GMC vehicle, you are for the repair or replacement of the tire if not automatically enrolled in the GMC Roadside Assistance covered by a warrantable failure.
Page 415: Canadian Roadside Assistance
(TTY) users, call 1-888-889-2438. Scheduling Service Appointments GMC reserves the right to limit services or reimbursement to an owner or driver when, in GMC’s When your vehicle requires warranty service, you should judgement, the claims become excessive in frequency or contact your dealer and request an appointment.
Page 416: Transportation Options
Public Transportation or Fuel If your vehicle cannot be scheduled into the service department immediately, keep driving it until it can be Reimbursement scheduled for service, unless, of course, the problem is If your vehicle requires overnight warranty repairs, safety-related. If it is, please call your dealership, let reimbursement of public transportation expenses may them know this, and ask for instructions.
Page 417: Vehicle Data Collection And Event Data Recorders
Additional Program Information Vehicle Data Collection and Event Data Recorders Courtesy Transportation is available during the Bumper-to-Bumper warranty coverage period, but Your vehicle, like other modern motor vehicles, has it is not part of the New Vehicle Limited Warranty. a number of sophisticated computer systems that A separate booklet entitled Warranty and Owner monitor and control several aspects of the vehicle’s Assistance Information furnished with each new vehicle...
Page 418 In a crash event, computer systems, such as the Airbag In addition, once GM collects or receives data, GM may: Sensing and Diagnostic Module (SDM) in your vehicle • use the data for GM research needs, may record information about the condition of the vehicle •...
Page 419: Collision Damage Repair
Collision Damage Repair Recycled original equipment parts may also be used for repair. These parts are typically removed from vehicles that were total losses in prior accidents. In most If your vehicle is involved in a collision and it is cases, the parts being recycled are from undamaged damaged, have the damage repaired by a qualiﬁed sections of the vehicle.
Page 420: Repair Facility
Repair Facility If your vehicle is leased, the leasing company may require you to have insurance that assures repairs with GM also recommends that you choose a collision repair Genuine GM Original Equipment Manufacturer (OEM) facility that meets your needs before you ever need parts or Genuine Manufacturer replacement parts.
Page 421 • • If you need roadside assistance, call GM Roadside Choose a reputable collision repair facility for your Assistance. See Roadside Assistance Program on vehicle. Whether you select a GM dealer or a page 7-6 for more information. private collision repair facility to ﬁx the damage, make sure you are comfortable with them.
Page 422: Reporting Safety Defects
Reporting Safety Defects Insurance pays the bill for the repair, but you must live with the repair. Depending on your policy limits, your insurance company may initially value the repair using Reporting Safety Defects to the aftermarket parts. Discuss this with your repair professional, and insist on Genuine GM parts.
Page 423: Reporting Safety Defects To The Canadian Government
In addition to notifying NHTSA (or Transport Canada) in Case Unit Repair Manual a situation like this, we certainly hope you’ll notify us. Please call us at 1-800-GMC-8782 (1-800-462-8782), or This manual provides information on unit repair write: service procedures, adjustments, and speciﬁcations for GM transmissions, transaxles, and transfer cases.
Page 424: Service Bulletins
Service Bulletins Current and Past Model Order Forms Service Bulletins give technical service information Service Publications are available for current and needed to knowledgeably service General Motors cars past model GM vehicles. To request an order form, and trucks. Each bulletin contains instructions to please specify year and model name of the vehicle.
Page 425 Anti-Lock Brake System (ABS) ......4-7 Anti-Lock Brake, System Warning Light ....3-35 Accessories and Modiﬁcations ......5-3 Appearance Care Accessory Power Outlet(s) ....... 3-19 Aluminum or Chrome-Plated Wheels ....5-96 Adding Equipment to Your Airbag-Equipped Care of Safety Belts ........5-94 Vehicle ............
Page 426 Audio System(s) (cont.) Braking ............4-6 Chime Level Adjustment ......3-101 Braking in Emergencies ........4-9 Fixed Mast Antenna ........3-101 Break-In, New Vehicle ........2-15 Navigation/Radio System, see Navigation Bulb Replacement ........... 5-47 Manual ........... 3-79 Center High-Mounted Stoplamp (CHMSL) Radio with Cassette and CD ......
Page 427 Cargo Lamp Light ........... 3-43 Cleaning (cont.) CD Changer ........... 3-93 Finish Care ..........5-95 Center Console Storage Area ......2-40 Inside of Your Vehicle ........5-90 Center High-Mounted Stoplamp (CHMSL) Instrument Panel, Vinyl, and Other and Cargo Lamp ......... 5-50 Plastic Surfaces ........
Page 428 Cupholder(s) ..........2-40 Door Customer Assistance Information Delayed Locking ........... 2-8 Courtesy Transportation ........7-7 Locks ............2-7 Customer Assistance for Text Power Door Locks ......... 2-8 Telephone (TTY) Users ....... 7-4 Programmable Automatic Door Locks ....2-9 Customer Assistance Offices ......7-4 Driver Customer Satisfaction Procedure .....
Page 429 Entry Lighting ..........3-18 Event Data Recorders (EDR) ......7-9 Exit Lighting ........... 3-18 Electrical System Extender, Safety Belt ........1-27 Add-On Equipment ........5-101 Center Instrument Panel Fuse Block ..... 5-104 Fuses and Circuit Breakers ......5-101 Instrument Panel Fuse Block ....... 5-102 Power Windows and Other Power Options ..
Page 430 Fuel (cont.) Gasoline Filling Your Tank ........... 5-6 Octane ............5-4 Fuels in Foreign Countries ......5-6 Speciﬁcations ..........5-5 Gage ............3-43 Glove Box ............. 2-40 Gasoline Octane ........... 5-4 GM Mobility Reimbursement Program ....7-5 Gasoline Speciﬁcations ........5-5 Low Warning Light ........
Page 431 Hood Checking Things Under ........5-8 Release ............5-9 Labeling, Tire Sidewall ........5-55 Horn ............... 3-6 Lamps How to Use This Manual ........ii Battery Run-Down Protection ......3-19 How to Wear Safety Belts Properly ....1-14 Cargo ............3-19 Dome ............
Page 432 Lighting Maintenance Schedule (cont.) Entry ............3-18 Recommended Fluids and Lubricants ..... 6-13 Exit ............3-18 Scheduled Maintenance ......... 6-4 Loading Your Vehicle ........4-42 Using ............6-2 Locks Your Vehicle and the Environment ....6-2 Delayed Locking ........... 2-8 Malfunction Indicator Light ........
Page 433 Park (P) Odometer ............3-29 Shifting Into ..........2-24 Odometer, Trip ..........3-29 Shifting Out of ..........2-25 Off-Road Driving ..........4-14 Parking Off-Road Recovery .......... 4-11 Brake ............2-23 Over Things That Burn ......... 2-26 Engine ............5-12 Passenger Airbag Status Indicator ..... 3-31 Pressure Gage ..........
Page 434 Rearview Mirror, Automatic Dimming with ® OnStar , Compass and Temperature Display ..2-28 Questions and Answers About Safety Belts ..1-13 Reclining Seatbacks .......... 1-4 Recommended Fluids and Lubricants ....6-13 Recovery Hooks ..........4-41 Recreational Vehicle Towing ......4-49 Remote Keyless Entry System ......
Page 435 Rocking Your Vehicle to Get it Out ....4-41 Seats (cont.) Routing, Engine Drive Belt ....... 6-15 Power Lumbar ..........1-3 Running the Engine While Parked ..... 2-27 Power Seats ..........1-2 Rear Seat Operation ........1-6 Reclining Seatbacks ........1-4 Secondary Latch System .........
Page 436 Spare Tire ............. 5-90 Theft-Deterrent, Radio ........3-96 Installing ............ 5-75 Theft-Deterrent Systems ........2-13 Removing ........... 5-72 Content Theft-Deterrent ........ 2-13 ® Storing ............5-86 Passlock ........... 2-15 Speciﬁcations, Capacities ....... 5-110 Tilt Wheel ............3-6 Speedometer ..........3-29 Tires .............
Page 437 Tires (cont.) Wheel Alignment and Tire Balance ....5-68 Vehicle Wheel Replacement ........5-68 Control ............4-6 When It Is Time for New Tires ...... 5-64 Damage Warnings ........... iv Tonneau Cover ..........2-41 Loading ............4-42 Tow/Haul Mode ..........2-22 Symbols ............
Page 438 Wheels Alignment and Tire Balance ......5-68 XM™ Satellite Radio Antenna System ....3-101 Different Size ..........5-66 Replacement ..........5-68 Where to Put the Restraint ....... 1-36 Windows ............2-10 Power ............2-11 Your Vehicle and the Environment ....... 6-2 Sliding Rear ..........

GMC Sierra Denali 2006 Owner's Manual

Section 1 Seats and Restraint Systems

Seats and Restraint Systems

Front Seats

Rear Seats

Safety Belts

Child Restraints

Airbag System

Restraint System Check

Section 2 Features and Controls

Features and Controls

Keys

Doors and Locks

Windows

Theft-Deterrent Systems

Starting and Operating Your Vehicle

Mirrors

Onstar System

Universal Home Remote System

Storage Areas

Sunroof

Vehicle Personalization

Section 3 Instrument Panel

Instrument Panel Overview

Climate Controls

Warning Lights, Gages, and Indicators

Driver Information Center (DIC)

Audio System(S)

Section 4 Driving Your Vehicle

Driving Your Vehicle

Your Driving, the Road, and Your Vehicle

Towing

Section 5 Service and Appearance Care

Service and Appearance Care

Service

Fuel

Checking Things under the Hood

All-Wheel Drive

Rear Axle

Front Axle

Windshield Wiper Blade Replacement

Tires

Appearance Care

Electrical System

Capacities and Speciﬁcations

Quick Links

Chapters

Related Manuals for GMC Sierra Denali 2006

Summary of Contents for GMC Sierra Denali 2006