SERVICING NOTICES ON CHECKING 1. KEEP THE NOTICES 6. AVOID AN X-RAY As for the places which need special attentions, Safety is secured against an X-ray by consider- they are indicated with the labels or seals on the ing about the cathode-ray tube and the high cabinet, chassis and parts.
CONTENTS SERVICING NOTICES ON CHECKING ...................... A1-1 HOW TO ORDER PARTS ........................... A1-1 IMPORTANT ..............................A1-1 CONTENTS ..............................A2-1 GENERAL SPECIFICATIONS ........................A3-1~A3-5 DISASSEMBLY INSTRUCTIONS 1.REMOVAL OF ANODE CAP ......................B1-1 2.REMOVAL AND INSTALLATION OF FLAT PACKAGE IC ............... B2-1, B2-2 SERVICE MODE LIST ..........................
GENERAL SPECIFICATIONS CRT Size / Visual Size 21 inch / 544.5mmV System CRT Type NORMAL Deflection degree Magnetic Field BV/BH +0.45G/0.18G Color System PAL/SECAM Speaker 1 Speaker Position Front Size 1.5 x2.5 Inch Impedance Sound Output 5.0 W 10%(Typical) 4.0 W DDR SECAM NTSC3.58(AV)+NTSC4.43 PAL60Hz...
Page 5
GENERAL SPECIFICATIONS On Screen Menu Display Menu Type Character Picture Contrast Brightness Color Tint (NTSC Only) Sharpness Audio Bass Treble Balance BBE On/Off Stable Sound On/Off CH Tuning Manual Auto CH Allocation Language Clock Set On Timer Set Off Timer Set Pin Code Registration Panel Lock Nicam Auto Off...
Page 6
GENERAL SPECIFICATIONS Clock and Sleep Timer Max Time - Min Timer Step Clock On Timer Program( On Timer) Off Timer Program( Off Timer) Wake Up Timer Timer Back-up (at Power Off Mode) more than G-10 Remote Unit RC-EY Control Glow in Dark Remocon Format Custom Code 40-BF h...
Page 7
GENERAL SPECIFICATIONS G-11 Features Auto Degauss Auto Shut Off Canal+ CATV Anti-theft(Back Up 30 Min.) Memory(Last CH) Memory(Last Volume) Auto Search CH Allocation Just Clock Function Game Position CH Label VM Circuit Full OSD Unitext Fastext Top Text Premiere Comb Filter Lines Auto CH Memory Stable Sound...
Page 8
GENERAL SPECIFICATIONS G-13 Interface Switch Front Power (Tact Sw) System Select Main Power SW Sub Power Channel Up Channel Down Volume Up Volume Down Rear AC/DC TV/CATV Selector Degauss Main Power SW Indicator Power Stand-by Stand-by/ON Yes(Red) On Timer Yes(Green) Terminals Front Video Input...
DISASSEMBLY INSTRUCTIONS 3. After one side is removed, pull in the opposite direction to 1. REMOVAL OF ANODE CAP remove the other. Read the following NOTED items before starting work. NOTE After turning the power off there might still be a potential Take care not to damage the Rubber Cap.
DISASSEMBLY INSTRUCTIONS REMOVAL AND INSTALLATION OF When IC starts moving back and forth easily after desoldering completely, pickup the corner of the IC using FLAT PACKAGE IC a tweezers and remove the IC by moving with the IC desoldering machine. (Refer to Fig. 2-3.) REMOVAL NOTE Put the Masking Tape (cotton tape) around the Flat...
Page 11
DISASSEMBLY INSTRUCTIONS INSTALLATION When bridge-soldering between terminals and/or the soldering amount are not enough, resolder using a Thin- Take care of the polarity of new IC and then install the tip Soldering Iron. (Refer to Fig. 2-8.) new IC fitting on the printed circuit pattern. Then solder each lead on the diagonal positions of IC temporarily.
SERVICE MODE LIST This unit provided with the following SERVICE MODES so you can repair, examine and adjust easily. To enter the Service Mode, press both set key and remote control key for more than 2 seconds. Remocon Key Set Key Operations Reset the user setting items (PICTURE, VOLUME, LANGUAGE and NICAM AUTO/ VOL.
WHEN REPLACING EEPROM (MEMORY) IC If a service repair is undertaken where it has been required to change the MEMORY IC, the following steps should be taken to ensure correct data settings while making reference to TABLE 1. Note: No need setting due to the adjustment value except the list below. Table 1 Enter DATA SET mode by setting VOLUME to minimum.
ELECTRICAL ADJUSTMENTS 1. ADJUSTMENT PROCEDURE 2. BASIC ADJUSTMENTS Read and perform these adjustments when repairing the 2-1: CONSTANT VOLTAGE circuits or replacing electrical parts or PCB assemblies. Place the set with Aging Test for more than 5 minutes. Connect the digital voltmeter to TP501. CAUTION Set condition is AV MODE without signal.
Page 15
ELECTRICAL ADJUSTMENTS 2-6: WHITE BALANCE 2-10: VERTICAL SIZE NOTE: Adjust after performing CUT OFF adjustment. Receive the monoscope pattern from the Pattern Generator. Place the set with Aging Test for more than 15 minutes. Using the remote control, set the brightness and Receive the gray scale pattern from the Pattern contrast to normal position.
Page 16
ELECTRICAL ADJUSTMENTS 2-13: COLOR CENT 2-15: Confirmation of Fixed Value (Step No.) Receive the PAL color bar pattern. (RF Input) Please check if the fixed values of the each adjustment Using the remote control, set the brightness, contrast items are set correctly referring below. and color to normal position.
ELECTRICAL ADJUSTMENTS PURITY AND CONVERGENCE 3-3: STATIC CONVERGENCE ADJUSTMENTS NOTE Adjust after performing adjustments in section 3-2. NOTE Receive the crosshatch pattern from the color bar Turn the unit on and let it warm up for at least 30 generator. minutes before performing the following adjustments.
Page 18
ELECTRICAL ADJUSTMENTS 4. ELECTRICAL ADJUSTMENT PARTS LOCATION GUIDE (WIRING CONNECTION) CRT PCB TP803 J801 TP801 CP801 CD803 VR420 VR401 J701 CP803A FB401 CP401 AC IN TP501 R521 CP802A CD501 CP501 VR501 L503 SPEAKER CP1002 CP502 MAIN PCB...
BLOCK DIAGRAM VOL UP TU001 MICON W/T.TEXT VOL DOWN IC101 OECF007A Q102 SCL SDA CH UP LED DRIVE ON_TIMER Q103 KEY_IN CH DOWN LED DRIVE STANDBY LED ON TIMER P.CON+5V D103 STAND BY/P.ON MEMORY SDA 19 D101 CHROMA AVDD1 IC199 IC201 STV2248C V-DRIVE SCL 20...
Page 27
SOUND AMP SCHEMATIC DIAGRAM (MAIN PCB) TO 21PIN FRONT_A_L FRONT_V_IN FROM MICON/TUNER A_MUTE FROM IF/CHROMA MONO_A_IN FRONT VIDEO J703 HTJ-032-03AY SOUND AMP (STEREO) IC IC1002 LA4600 R707 FROM POWER 100 1/2W FRONT AUDIO L D1001 J704 AT+5V_AVDD HTJ-032-03AW 1SS133 ATT. RIPPLE C736 BUFFER...
WAVEFORMS MICON/TUNER IF/CHROMA 50µs 20µs 0.5µs 100mV 0.50V 1.00V 10ms 50µs 1.00V 100mV 200mV 20µs 20µs 50µs 1.00V 1.00V 0.50V 0.2ms 20µs 20µs 1.00V 1.00V 1.00V 50µs 0.2ms 20µs 100mV 1.00V 1.00V NOTE: The following waveforms were measured at the point of the corresponding balloon number in the schematic diagram.
WAVEFORMS 20µs 20µs 20µs 100mV 1.00V 1.00V 20µs 20µs 1.00V 1.00V 200mV 20µs 10ms 100mV 1.00V 200mV DEFLECTION/CRT 20µs 20µs 10ms 1.00V 200mV 1.00V 21PIN/AV SW 10ms 20µs 20µs 10.0V 1.00V 1.00V NOTE: The following waveforms were measured at the point of the corresponding balloon number in the schematic diagram.
WAVEFORMS 10ms 20µs 10.0V 20µs 20µs 10.0V SOUND AMP 20µs 0.50V 5.0V 0.2ms 2µs 200V 5.0V 20µs NOTE: The following waveforms were measured at the point of the corresponding balloon number in the schematic diagram.