COLOR MONITOR SERVICE MANUAL CHASSIS NO. : CA-111 FACTORY MODEL: EB990G MODEL: StudioWorks E900B (EB990G-EL) StudioWorks E900B (EB990G-ES) E900B (EB990G-EL) CAUTION BEFORE SERVICING THE UNIT, READ THE SAFETY PRECAUTIONS IN THIS MANUAL. MENU SELECT...
SAFETY PRECAUTIONS SAFETY-RELATED COMPONENT WARNING! X-RADIATION There are special components used in this color monitor The only potential source of X-radiation is the picture tube. which are important for safety. These parts are marked However, when the high voltage circuitry is operating on the schematic diagram and the replacement properly there is no possibility of an X-radiation problem.
TIMING CHART VIDEO SYNC FACTORY PRESET MODE MODE MARK MODE 1 MODE 2 MODE 3 MODE 4 MODE 5 VESA Sync Polarity – Frequency 43.269 53.674 68.677 91.146 93.750 µs Total Period 23.112 18.631 14.561 10.971 10.666 µs Video Active Time 17.778 14.222 10.836...
OPERATING INSTRUCTIONS FRONT VIEW REAR VIEW ID Label MENU SELECT Power ON/OFF Button AC Power Socket See Front Control Panel Signal Connector Front Control Panel MENU Button SELECT Button Power (DPMS) Indicator MENU SELECT Power Button Buttons Button 1. Power ON/OFF Button Use these buttons to choose or adjust items in the on Use this button to turn the monitor ON or OFF.
1. TILT/SWIVEL & BACK COVER REMOVAL 1) Set the monitor face downward. 2) Pull the latch (a), carefully remove the Tilt/Swivel by pulling it upward. 3) Pressing the latch (b), Back cover by pushing it upward. 4) Release the latch (c). 5) Slide the Back Cover away from the Front Cabinet of the monitor.
DESCRIPTION OF BLOCK DIAGRAM 1. Line Filter & Associated Circuit. 5. X-ray Protection. This is used for suppressing noise of power input line This circuit detects the rectified DC voltage comes flowing into the monitor and/or some noise generated from the FBT pin 4. If the high voltage of the FBT in this monitor flowing out through the power input reaches up to about 30kV (abnormal state), H.V control (IC802) detects.
Page 11
11. D/D Drive & Convert Circuit. 19. Image Rotation (Tilt) Circuit. This circuit is used for supplying B + voltage to This circuit corrects the tilt of the screen by supplying horizontal deflection output transistor (Q801). This the image rotation signal to the tilt coil which is circuit makes to add side-pincushion correcting signal attached to the CDT near the deflection.
ADJUSTMENT GENERAL INFORMATION 3) EEPROM → ALL CLEAR → Y(Yes) command. All adjustment are thoroughly checked and corrected <Caution> Do not run this procedure unless the when the monitor leaves the factory, but sometimes EEPROM is changed. All data in EEPROM (mode several adjustments may be required.
Page 13
± 0.1FL of 5. Input EDID Data. 11) Adjust SUB-Brightness command to 0.4 1) Display color 15,0 cross hatch pattern at Mode 4. the raster luminance. 2) EEPROM → Write EDID command and confirm 12) Display color 15,0 box pattern(70x70mm) at mode “EDID Write OK!!”...
TROUBLESHOOTING GUIDE 1. NO POWER NO POWER (POWER INDICATOR OFF) CHECK TROUBLE IN FUSE OK? FUSE (F901) CHECK TROUBLE IN D901 BRIDGE DIODE BRIDGE DIODE? (D901) CHECK C905(+) VOLTAGE TROUBLE IN 145VDC at 110V input IC901 310VDC at 220V input CHECK TROUBLE IN D924, D926, D923,...
Page 15
2. NO CHARACTER NO CHARACTER TROUBLE IN CHECK P301, SIGNAL CABLE, IC302 PIN 5, 6, 7 ? PC SIGNAL CHECK TROUBLE IN IC302 PIN 18, 19, 20, IC302, P302 PIN 9 (5V) ? CHECK IC303 PIN 1, 3, 5 TROUBLE IN PIN10 (12V), IC303 PIN 6 (80V) ?
Page 16
3. NO RASTER NO VIDEO (POWER INDICATOR GREEN or AMBER) CHECK AMBER POWER INDICATOR TROUBLE IN GREEN or AMBER ? P302 SIGNAL CABLE GREEN MIN. ROTATE SCREEN CHECK (Counter-clockwise) CONTROL KNOB TO SCREEN CONTROL CLOCKWISE KNOB OF FBT CHECK VOLTAGE AT D924/D926 CATHODE (190V) TROUBLE IN PRIMARY D923 CATHODE (80V)
4. NO VERTICAL DEFLECTION NO V-DEFLECTION (ONE HORIZONTAL LINE) CHECK TROUBLE IN IC601 Pin 2 T901 PIN 15 (15V) ? CHECK TROUBLE IN IC601 PIN 7 T701 PIN 4, D704 (40V)? CHECK TROUBLE IN IC701 PIN 13 IC701 (SAWTOOTH WAVE)? TROUBLE IN IC601, V-CIRCUIT...
Page 18
5. TROUBLE IN DPM STAND-BY/SUSPEND/ OFF MODE FAILURE CHECK CHECK PC, IC401 (MICOM) NO H / V SYNC SIGNAL (PC IS NOT GOING INTO PIN 40, 41 (H/V INPUT) DPM MODE) SIGNAL? INPUT H/V SYNC CHECK TROUBLE IN IC401 PIN 9, 8 X401, IC401 WAVEFORM? CHECK...
6. NO DEGAUSSING NO DEGAUSSING CHECK TROUBLE IN IC401 PIN 6 IC401 (MICOM) (5V)? CHECK TROUBLE IN Q920 COLLECTOR D925 VOLTAGE (0.5V)? CHECK TROUBLE IN P901? P901 CHECK TROUBLE IN RL901? RL901 TROUBLE IN TH901, DEGAUSSING COIL...
Page 20
7. TROUBLE IN OSD NO OSD CHECK TROUBLE IN IC301 PIN 4 P302 (5V) ? CHECK IC301 PIN 5 TROUBLE IN (NEGATIVE H-PULSE P302 COMES IN ?) CHECK IC301 PIN 10 TROUBLE IN (V-PULSE COMES IN?) P302 CHECK IC301 PIN 13, 14, 15 TROUBLE IN (IS THERE ANY SIGNAL IC301, IC401...
MAIN TOTAL ASSEMBLY EB990G BRAND CA-111 FOR EUROPE (EB990G-ES) 6871TVT283A PWB(PCB) ASSEMBLY,VIDEO, EB990G VIDEO TOTAL BRAND CA-111 6871TMT299F PWB(PCB) ASSEMBLY,MAIN, EB990G ALEUE BRAND CA-111 TOTAL FOR EUROPE (EB990G-EL) 6871TMT299C PWB(PCB) ASSEMBLY,MAIN, EB990G ALMXE BRAND CA-111 TOTAL FOR MEXICO (EB990G-EL) 6871TMT299E PWB(PCB) ASSEMBLY,MAIN, EB990G ALUKE BRAND CA-111 TOTAL FOR U.K (EB990G-EL)
REPLACEMENT PARTS LIST CAUTION: BEFORE REPLACING ANY OF THESE COMPONENTS, READ CAREFULLY THE SAFETY PRECAUTIONS IN THIS MANUAL. * NOTE SAFETY Mark AL ALTERNATIVE PARTS DATE: 2002. 5. 21. DATE: 2002. 5. 21. *S *AL LOC. NO. PART NO. DESCRIPTION / SPECIFICATION *S *AL LOC.