Download Print this page
Interfire A1000.2 Instruction Manual

Interfire A1000.2 Instruction Manual

2 channel / 4 channel / 5 channel automotive amplifier

Advertisement

2 CHANNEL / 4 CHANNEL / 5 CHANNEL
AUTOMOTIVE AMPLIFIER
A300.2 / A500.2 / A700.2
A1000.2 / A1100.2 / A2200.2
A500.4 / A700.4 / A900.4 / A800.5
INSTRUCTION MANUAL

Advertisement

loading
Need help?

Need help?

Do you have a question about the A1000.2 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for Interfire A1000.2

  • Page 1 2 CHANNEL / 4 CHANNEL / 5 CHANNEL AUTOMOTIVE AMPLIFIER A300.2 / A500.2 / A700.2 A1000.2 / A1100.2 / A2200.2 A500.4 / A700.4 / A900.4 / A800.5 INSTRUCTION MANUAL...
  • Page 2 Your new high fidelity bridgeable/stereo amplifier is designed to deliver maximum enjoy ment and one year of trouble free service. Please take a few moments to read this manual thoroughly. It will explain the features and operation of your unit and help insure trouble free installation.
  • Page 3 • NEVER operate the amplifier without the proper power and ground wire, 10 gauge minimum. • NEVER operate the amplifier without proper fusing. Fuse holder must be located with in 0.5 meters from the battery. This fuse is to protect the car not the electronics. In case of a short, the fuse will blow instead of the wire burning up.
  • Page 4 MOUNTING: 1. After reading precaution, decide where you are going to install the unit. Also, see Fig.1. 2. Once the location has been determined, place the amplifier into position. Using a felt tip pen or pencil mark the four holes to be drilled for mounting. NEVER use the amplifier as a template for drilling.
  • Page 5 This amplifier will accept low level inputs only. Low level is the same as line level. The low level signal is carried through RCA cables. It is preferred to use low level inputs to the amplifier if the head unit is equipped with the low level outputs. If not, you can use a "high to low converter"...
  • Page 6 0.2V 0dB 12dB 50Hz 250Hz L.P.F H.P.F 80Hz 1.2KHz GAIN BASS L.P.F FLAT H.P.F CROSSOVER LINE INPUT +12V REM GND CAR STEREO HEAD UNIT FIG.2...
  • Page 7 L.P.F H.P.F 6V 0.2V 12dB FLAT 50Hz 500Hz GAIN BASS CROSSOVER CH 1/2 LINE INPUT +12V REM GND CAR STEREO HEAD UNIT L.P.F H.P.F 50Hz 500Hz FLAT 0dB 12dB 6V 0.2V BASS GAIN CROSSOVER CH 3/4 LINE INPUT FIG.2...
  • Page 8 CH 1/2 LINE INPUT CROSSOVER GAIN L.P.F 0.2V 50Hz 250Hz FLAT L.P.F H.P.F 0.2V 50Hz 250Hz FLAT CH 3/4 +12V REM GND CAR STEREO HEAD UNIT CH 5 CROSSOVER LINE INPUT H.P.F H.P.F L.P.F 80Hz 1.2kHz 80Hz 1.2kHz FLAT 50Hz 250Hz 80Hz 1.2kHz...
  • Page 9 This amplifier can operate in one, two or three channel mode. The minimum impedance for single channel (bridged/mono) operation is 4 or 8 ohms. Tri channel power is referred to stereo and mono at the same time. Minimum impedance remains the same for three channel (front /subwoofer) systems as long as proper passive crossovers are used.
  • Page 10 2 SPEAKER BRIDGED POWER PROTECT 2 SPEAKER + 1 SUBWOOFER POWER PROTECT 4 SPEAKER STEREO POWER PROTECT 6 SPEAKER HEX MODE POWER PROTECT SPEAKER (+) CH4 FUSE BRIDGED BRIDGED 4-8 Ohms 1 CH 2 CH SPEAKER (+) CH4 FUSE BRIDGED BRIDGED 2-4 Ohms SUB WOOFER...
  • Page 11 3 SPEAKER BRIDGED POWER PROTECT 5 SPEAKER STEREO POWER PROTECT 7 SPEAKER HEX MODE POWER PROTECT 4-8 Ohms SPEAKER (+) CH1 (+) CH2 (+) CH3 (+) CH4 (+) CH5 FUSE BRIDGED BRIDGED 4-8 Ohms 2-8 Ohms 1 CH 2 CH 3 CH SPEAKER (+) CH1...
  • Page 12 1.Set to the "H.P.F" position when the amplifier is used to drive a tweeter/midrange system. The frequencies below the crossover point will be attenuated at 12dB/octave. Permits adjustment of the crossover frequency ,by rotating the knob to select any frequency between 80Hz to 1.2kHz &...
  • Page 15 This section provides you with a catalog of amplifier symptoms and their probable causes and solutions. Before you consult this listing, make sure the vehicle's electrical system is working properly by verifying that other electrical items (e. g. headlights, windows, etc.) Still function correctly.
  • Page 16 FUSE RATING 30 A DIMENSIONS 250x59x200 250x59x250 250x59x320 250x59x400 250x59x400 (W mm x H mm x D mm ) A500.2 A700.2 A1000.2 A1100.2 100W x 2 150W x 2 225W x 2 225W x 2 250W x 1 350W x 1...
  • Page 17 AMPLIFIER 4 OHMS @ 0.05% THD 4 OHMS Bridged 0.5% THD MAXIMUM OUTPUT POWER BASS LEVEL REMOTE CONTROL(16.4Ft) LOW PASS FILTER HIGH PASS FILTER FREQUENCY RESPONSE (-1dB) SIGNAL TO NOISE RATIO (`A' WTD) INPUT SENSITIVITY INPUT IMPEDANCE OPERATION VOLTAGE (NEGATIVE GROUND) SPEAKER IMPEDANCE @ STEREO DRIVEN FUSE RATING DIMENSIONS (W mm x H mm x D mm )
Save PDF