PRO MIXER DX2000USB User Manual 9. Do not defeat the safety purpose of the polarized TO BIND MUSIC GROUP BY ANY EXPRESS OR IMPLIED Important Safety or grounding-type plug. A polarized plug has two blades UNDERTAKING OR REPRESENTATION. THIS MANUAL Instructions with one wider than the other.
TALK OVER feature can automatically and temporarily reduce the music level while you are speaking. We have given particular attention to metering your Please register your mixer on our website at behringer.com to become eligible for music with PFL offered on every channel. In addition, all channels have signal our extended warranty.
Compressors can help even out voice volume, adding loads of energy, but they can also cause feedback problems if over-used. Noise gates Your BEHRINGER PRO MIXER DX2000USB was carefully packed in the factory shut off mics automatically when not in use—useful for keeping and the packaging was designed to protect the unit from rough handling.
PRO MIXER DX2000USB User Manual 3.1 Input selection ◊ Normally you will want to PFL only one channel at a time. This might not be true if you are layering tracks, and/or using “Permanent PFL”— Inputs are on the DX2000USB’s back panel. Your input source is selectable see the chapter 7 “HEADPHONES, MONITORS &...
PRO MIXER DX2000USB User Manual To set up these controls properly, first turn DAMPING full on (MAX). Set up the the X or Y output. In PUNCH mode the X button (34) introduces the X signal to gain on your mic channel using PFL. Now adjust SENSITIVITY until the music is the mix, while the Y button (35) brings in the Y signal.
PRO MIXER DX2000USB User Manual 5.6 Effect return 6.2 Headphones—read carefully—this is tricky! A line-level stereo effect RETURN (54) (Max. gain 30 dB) feeds directly into the mix, level being adjusted by the FX RETURN knob (42) . This input is designed...
PRO MIXER DX2000USB User Manual (61) (60) (64) (65) (66) (68) (69) (53) (55) (74) (50) (51) (71) (72) (52) (73) (63) (62) (67) (70) (54) (56) (57) (58) (59) 7. Sub Bass 9. Connections The sub bass output (63) on the back panel comes with two rotary controls, 9.1 PRO MIXER DX2000USB connections...
Page 10
Please ensure that only qualified persons install and operate the (72) IEC socket. For connecting the mixer a standard IEC cable. Always connect PRO MIXER DX2000USB. During installation and operation the user the mixer to a wall outlet before engaging the POWER switch.
PRO MIXER DX2000USB User Manual 9.2 Plug soldering guide Balanced use with XLR connectors You will need a lot of cables for different purposes—see the following figures to make sure you have got the right ones. Use custom-made RCA cables for all connections which use RCA sockets (centre post = signal (+ve) and sleeve = ground/screen).
OVERLAP and SLOPE. You can unscrew the bottom of your mixer to reach the main motherboard. ◊ Please be aware that the BEHRINGER warranty becomes discretionary when you start disassembling your DX2000USB! Don’t even think of it, if you make much of your warranty privileges. Sorry, but we have to mention this.
PRO MIXER DX2000USB User Manual 11. Specifications Mono Input Channels Connectors Electronically balanced, Mic Input Master Out discrete input configuration Jack 0 dB Gain +10 to +60 dB +6 dB Frequency response 10 Hz to 80 kHz, +/-3 dB Monitor Out 0.08 % typ.
Page 15
PRO MIXER DX2000USB User Manual FEDERAL COMMUNICATIONS COMMISSION COMPLIANCE INFORMATION PRO MIXER DX2000USB MUSIC Group Services US Inc. Responsible Party Name: 18912 North Creek Parkway, Address: Suite 200 Bothell, WA 98011, +1 425 672 0816 Phone Number: PRO MIXER DX2000USB complies with the FCC rules as mentioned in the following paragraph:...
Need help?
Do you have a question about the PRO MIXER DX2000USB and is the answer not in the manual?
Questions and answers