Table of Contents
Advertisement
Quick Links
Download this manual
See also:
Operating Manual
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for TMB ProFan
Summary of Contents for TMB ProFan
- Page 1 Operating Manual Rev 020513...
-
Page 2: Table Of Contents
3-Pin to 5-Pin Conversion 5. OPERATING INSTRUCTIONS......... BackPack Overview Connecting the BackPack Controller DMX Mode Manual Mode Master/Slave Operation Using ProFan with a Smoke Machine 6. TROUBLESHOOTING AND MAINTENANCE....Troubleshooting Cleaning Replacing the Fuse 7. SAFETY INSTRUCTIONS..........8. APPENDIX............... Limited Warranty... -
Page 3: Before You Begin
ProFan is a powerful and versatile DMX-controlled professional fan designed for a variety of applications: Studios, theatres, theme parks, touring, photographic, and more. ProFan is perfect for filling large areas with smoke and haze; creating special wind effects; blowing confetti, snow or bubbles; general air circulation, ventilation, and ambient cooling. -
Page 4: Exploded Views
ProFan Operating Manual BackPack Controller Blade Power Supply Motor Grille Body Knob Yoke Knob Back Panel Detail... -
Page 5: Assembly
Included with the ProFan is a multipurpose yoke assembly for standing on the floor or mating the unit to a stand or suspension clamp. The yoke assembly easily attaches to the ProFan using the hardware and wrench included with each ProFan unit... -
Page 6: Attaching The Yoke Assembly
7. Tighten the Allen bolt and the T-Handle until the yoke assembly is fixed and not easily moved. 8. At this point the ProFan is ready for mating with a stand or clamp. Grip the fan by its tubular housing brackets when lifting or mounting to avoid pinching hands or fingers. -
Page 7: Overhead Rigging
ProFan Operating Manual ProFan yoke spigot and rigging crossbar Overhead Rigging Proper rigging clamps may be attached to the ProFan yoke via the 9/16” bolt hole located on the crossbar at the base of the yoke. Recommended ProBurger rigging clamps: 1. -
Page 8: Remote Control
ProFan Operating Manual 4. R EMOTE ONTROL Basics of DMX Control There are 512 channels in a DMX-512 universe. Channels may be assigned in any manner. Any device capable of receiving DMX- 512 will require one or a number of sequential channels. The user must assign a starting address on the fixture that indicates the first channel reserved in the lighting console. -
Page 9: Cable Connectors
ProFan Operating Manual Minimum 2-conductor twisted pair plus a shield Maximum capacitance between conductors – 22 pF/ft. Maximum capacitance between conductor and shield – 41 pF/ft. Maximum resistance of 14.5 ohms / 1000 ft. Characteristic impedance of 80 – 110 ohms... -
Page 10: 3-Pin To 5-Pin Conversion
ProFan Operating Manual 3-Pin to 5-Pin Conversion Chart If you use a console with a 3-pin DMX output connector, you will need to use a 3-pin to 5-pin adapter. The chart below details a proper conversion: 3-Pin Male 5-Pin Male... -
Page 11: Operating Instructions
ProFan Operating Manual 5. O PERATING NSTRUCTIONS BackPack Overview XLR 3-pin male connector to ProFan DMX/MANUAL LCD Display Mode switch Button: 1. Hold down and slide DMX512 input & Slide Fader Control: fader to set DMX output XLR 5-pin 1. Fan Speed Control in... -
Page 12: Connecting The Backpack Controller
ProFan Operating Manual Connecting the BackPack Controller With rear Power switch in OFF position: Connect the integral male XLR on the BackPack directly to the integral female XLR on the fan body. If desired, the BackPack can be removed and connected using a standard 3-pin XLR microphone cable up to 60 ft / 20 m in length. - Page 13 BackPack by locating into the bottom housing slot. CAUTION: Double-check that the BackPack is securely fixed to the fan housing prior to use. Note: Ensure the ProFan is pointed in a direction where considerable wind will not cause a disturbance or any safety issues.
-
Page 14: Dmx Mode
When the recessed switch on the BackPack is switched to "DMX", the display will indicate that the unit is in DMX Mode and will display the current address of the ProFan. If no incoming DMX signal is detected, the display will then read "No DMX Found". -
Page 15: Manual Mode
ProFan Operating Manual Manual Mode When the recessed switch on the BackPack is switched to "MANUAL", the display will indicate that the unit is in Manual Mode. The display will also indicate the current speed of the fan, based on the position of the fader and whether the Full Speed button is depressed. -
Page 16: Master/Slave Operation
ProFan to another. 1) Connect each controller to each fan via the built-in XLR 3- pin line female connector. 2) Use 5-pin XLR DMX cables to connect the master ProFan output (female XLR) to the next "slave" ProFan input (male XLR). -
Page 17: Using Profan With A Smoke Machine
ProFan Operating Manual Using ProFan with a Smoke Machine When using ProFan with smoke, fog or hazer machines, place the fan behind the machines as illustrated below. Do not place the fan in front of the machine. This will cause residue build-up on the fan blades and degrade the quality of the smoke, fog, or haze. -
Page 18: Troubleshooting And Maintenance
ProFan Operating Manual 6. T ROUBLESHOOTING AND AINTENANCE Troubleshooting Problem Symptom/Cause Suggested Remedy Display says "No Connect DMX DMX Found" Power is supplied, but fan Press button and move Incorrect DMX does not operate fader until correct address via DMX... -
Page 19: Cleaning
2. Remove the screws to clean the housing and blades 3. After cleaning, make sure that screws are securely tightened Replacing the Fuse ProFan uses a 10A, 125V cartridge-type wire fuse, 0.8”L x 0.21”DIA (20.46 x 5.34 mm): 1. Turn the fuse knob counter-clockwise 2. -
Page 20: Safety Instructions
Preventing Fire and Electric Shock • Always ground (earth) the machine electrically. • ProFan has a built-in speed control. Do not connect ProFan to any external solid-state speed control device or dimmer circuit. • Disconnect the machine from power before removing any components or servicing, and when not in use. -
Page 21: Appendix
30 days after delivery. All warranty parts will be charged to the customer until faulty parts (or product) are returned to TMB for valuation. These parts must be returned within 30 days of receipt or warranty is void and parts/shipping becomes billable items. -
Page 22: Technical Specifications
ProFan Operating Manual Technical Specifications Width 19” (480 mm) Height 22” (560 mm) Depth 18” (460 mm) PHYSICAL Weight 27.6 lbs (12.5 kg) Mounting Adjustable swivel yoke Color Black Nominal voltage 100-240VAC, 50-60Hz Maximum power 1200W consumption ELECTRICAL 10A 125V cartridge, wire: (L x DIA) 0.8”... -
Page 23: Contact Information
ProFan Operating Manual 19" (480mm) 18" (460mm) Contact Information TMB Worldwide TMB LA: +1 818.899.8818 TMB NY: +1 201.896.8600 TMB UK: +44 (0)20.8574.9700 TMB Canada: +1 519.986.9991 TMB Beijing: +86 10.8492.1587 e-mail: tmb-info@tmb.com web: www.tmb.com TMB 24/7 Technical Support US/Canada: 1 877.TMB.DUDE (1 877.862.3833)
Need help?
Do you have a question about the ProFan and is the answer not in the manual?
Questions and answers