Page 2
NFORMA TION ’ OBALT OATS WNER ANUAL Owner’s Name Address City State Hm. Phone Wk Phone Cobalt Model Model Year Hull Serial No. Engine Engine Serial No. Drive Drive serial No. Dealership Address City State Main Phone Service Phone Sales Contact Service Contact Extended Warranty Contract No.
Page 3
ANUAL Dear New Cobalt Owner, From all of us at the factory and from your Cobalt Dealer, thank you for purchasing a Cobalt. We greatly appreciate your business and look forward to a long and enjoyable relationship with you as part of the Cobalt family.
National Marine Manufacturers Association and the American Boat and Yacht Council work with boat builders to develop voluntary standards that exceed base requirements. The safety equipment on your Cobalt meets or exceeds the standards of the U.S. Coast Guard, N.M.M.A., and the A.B.Y.C.
QUIPMENT AND OVERNMENT EGULATIONS DDITIONAL ECOMMENDED AFETY QUIPMENT In spite of all efforts to the contrary, problems or mishaps sometimes occur while boating. The items listed below should help make unexpected events more manageable: • Anchor and anchor line • Compass •...
Every Cobalt is built to meet or exceed all applicable standards of these organizations at the time of manufacture. Each model is inspected and certified prior to introduction, and periodic inspections of the entire model line are conducted in-plant to insure...
INYL NTERIOR AND PHOLSTERY The vinyl fabric in your Cobalt’s interior has been especially selected to take the tough punishment of the elements and hard usage of an active boater. Avoid sharp objects that may cut or tear your vinyl.
NTERIOR XTERIOR a clean cloth. STEP 2 CLEANERS* Solvent-type cleaner to be liberally applied with a cloth, damp sponge or fine bristle brush. • Rubbing alcohol (isopropyl alcohol). • Lighter fluid (naphtha). Rinse cleansed area with fresh water and dry with a clean cloth.
ARPET The carpet in your Cobalt is made of the finest materials available. Scrubbing with soapy water will handle most tough jobs. A simple hosing for mild cleanups will bring out that new look. Thoroughly air dry before reinstallation into your boat. Your dealer can suggest methods of cleaning difficult stains in your carpet.
NTERIOR XTERIOR first few months after initial installation. When canvas items are erected on the boat and properly adjusted, shrinkage will only occur in areas of looseness. Mold and mildew can be avoided by keeping the canvas clean and well ventilated. DIRT Dirt can create a starting point for mold when moisture is present.
IBERGLASS INISH The finish on your Cobalt is known as gelcoat. The gelcoat used by Cobalt is the finest available on the market today. With all its properties, it is not impervious to the elements and many types of water conditions.
NTERIOR XTERIOR Stainless steel, though highly resistant, is still capable of rusting, particularly in the marine environment. Initial signs of rust and corrosion, left untreated, may result in pitting and permanent damage to components. The following steps will help protect against such occurrence: PREVENTIVE STEPS 1.
PERA TION PERA TION ’ OBALT OATS WNER ANUAL RECTING ONVERTIBLE 1. Remove canvas top assembly from “top storage area”. 2. Attach top bow ends to top mounts on each side of the boat. Use quick disconnect pins. 3. Remove storage boot and unroll canvas top.
8. Snap side curtains and camper top to deck and/or windshield. DO NOT OPERATE YOUR COBALT WITH THE CANVAS COMPLETELY ENCLOSED. THE COCKPIT AND CABIN MUST BE OPEN TO AVOID CARBON MONOXIDE FUMES AND TO PROVIDE PROPER FUEL COMPARTMENT VENTILATION. EXHAUST FUMES FROM COMBUSTION ENGINES CONTAIN CARBON MONOXIDE.
PERATION 23LS/25LS/293 1. Bimini top is stored in the upright position for both trailering and storage. 2. Open top and extend the telescoping legs by depressing the buttons protruding through the sides of the legs. 3. Install support leg ends to the appropriate mounting brackets on the deck or windshield.
™ polyester that will properly protect the gelcoat finish on the deck of your Cobalt. Do not use convertible tops, side curtains, aft curtains, tonneau covers, etc. for long term storage. These tops were not designed for long term storage.
PERATION SUNBRELLA FABRIC This is a woven fabric made of 100% solution dyed acrylic fiber. It is very colorfast and will withstand long-term exposure to the sun (ultra-violet) without excessive fading or deterioration. CLEANING INSTRUCTIONS Fabric should be cleaned regularly before substances such as dirt, roof particles, etc. are allowed to accumulate on and become embedded in the fabric.
PERATION CARE • NEVER store canvas wet or in an unventilated, moist area. • Always roll the canvas instead of folding. This is of particular importance on side curtains or any part with the clear vinyl “glass”. • Roll the top carefully around the bows and cover with the storage boot provided. •...
AFETY WITCH Your Cobalt is equipped with an ignition safety switch. It is located on the face of the side mount control or near the lower edge of the driver’s control panel. The driver should always attach the lanyard to his or her person. If the driver leaves the driver’s station, the lanyard will shut off the ignition immediately preventing the boat...
PERIODIC BASIS BY A QUALIFIED SERVICE TECHNICIAN. BOARDING LADDERS Your Cobalt is equipped with a folding boarding ladder. Never use the swim platform area and/or the boarding ladder while the engine(s) is running. The propeller(s) is very sharp and can cause bodily harm. Always make sure the boarding ladder is properly stowed and there is no one in the area behind the boat before starting the engine and engaging the shift mechanism.
PERATION ARNING ABELS Your Cobalt has several warning labels displayed to point out safety hazards. The areas are as follows: BOARDING LADDER/SWIM WARNING PLATFORM PROPELLER LOCATED BEHIND THIS BOAT. CONTACT MAY CAUSE SEVERE INJURY OR FATALITY. DO NOT APPROACH OR USE LADDER AND PLATFORM WHEN THE ENGINE IS RUNNING.
MANEUVERABILITY ABOVE 50 MPH IS LIMITED. SUDDEN TURNS MAY CAUSE LOSS OF CONTROL. WAKE JUMPING - YOUR COBALT IS NOT DESIGNED FOR WAKE JUMPING. WHEN CROSSING ANOTHER BOAT’S WAKE, THROTTLE BACK TO PREVENT YOUR BOAT FROM LEAVING THE WATER. WAKE JUMPING IS VERY DANGEROUS. IT IS POSSIBLE FOR THE BOAT TO RE-ENTER THE WATER ON ITS SIDE, TRANSOM, OR BOW.
IFTING OBALT Please consult your Cobalt dealer for the proper method of lifting your Cobalt. THE SKI TOW CANNOT BE USED TO LIFT THE BOAT. IT CAN ONLY BE USED FOR WATER SKIING. IT IS NOT DESIGNED FOR TOWING ANOTHER BOAT OR FOR PARASAILING. THE TRANSOM MOUNTED EYES SHOULD BE USED FOR PULLING A HEAVIER LOAD.
OPTIONAL Docking lights are to be used for docking only. It is illegal to use your docking lights while cruising. Please consult your Cobalt dealer for further information. OPTIONAL The trim tabs are a separate system in themselves and are not to be used in lieu of the engine power trim system.
ATTERY WITCH Your Cobalt is equipped with a master battery switch. With this switch turned off, nothing in the boat will operate. If you have the optional dual battery system, make sure the master switch is in the “1” or “2” position. You can operate the boat with the switch in the “both”...
EASON TORAGE Store your Cobalt with the bow slightly elevated; i.e., the same attitude as if the boat were floating at rest. Remove the transom drain plug. If the boat is stored with the bow down, moisture will not be able to move to the engine bilge area and out of the boat.
ECHNICAL NFORMATION you are storing your Cobalt by some other means; rack, hoists, blocks, etc., consult your Cobalt Dealer. Your dealer can assist you in making sure your boat has proper support. It is very important the proper canvas is used as designed. The canvas listed in items 1 and 2 are made of Sunbrella, an acrylic material.
ECHNICAL NFORMATION Circuit Breakers Most electrical standard equipment devices are controlled with circuit breakers. These breakers will activate if overloaded and cut power to the switch. To restore power, simply push the breaker button in and release. (Breakers do not require fuse replacement).
Notification of any warranty claim, arising within the applicable warranty period, as set forth above, must be made in writing by the owner of the Cobalt boat or by an authorized Cobalt Boats dealer to Cobalt Boats within thirty (30) days after the discovery of the alleged basis...
During the applicable warranty period, as set forth above, warranty repairs shall be made without charge by an authorized Cobalt Boats dealer or, at the option of Cobalt Boats, by Cobalt Boats at its plant in Neodesha, Kansas. All warranty repairs shall be subject to the authorization of factory-trained personnel of Cobalt Boats, whose decision will be final.
GNITION AFETY WITCH Your Cobalt is equipped with an ignition safety switch located on the lower lip of the dashboard. Make sure the lanyard is installed with the switch holding the lanyard in place. Please consult your Cobalt dealer. WHENEVER CHECKING FOR ELECTRICAL PROBLEMS USE EXTREME CAUTION.
Throttle not fully open - Check to see that throttle opens fully at engine. Improper fuel - Fill tank with correct fuel. Overheating - Immediately turn off the engine and contact your Cobalt dealer. Boat overloaded - Reduce load. Boat trim - Distribute boat load evenly.
ARE NOT BLOCKED BY CANVAS OR OTHER OBSTACLES. 9. Circuit Breakers - Push to reset if necessary. If the button continues to pop out, consult your Authorized Cobalt Dealer. The 190 breaker panel is located under the dash. 10. Two Position Switch - Controls equipment as labeled.
ODEL PECIFIC NFORMATION ’ APTAIN HAIR DJUSTMENT AND PERATION Your captain’s chair has the flip-up position for greater visibility and maneuverability while docking. You can sit on the raised cushion or stand in front of the cushion. The 190 driver’s captain’s chair is adjustable fore and aft and also rotates. There is a large handle on the inboard side of the mechanism that when loosened, allows the seat to slide fore and aft.
PECIFIC NFORMATION INCORRECT PROPELLER APPLICATION CAN CAUSE ADVERSE HANDLING CHARACTERISTICS. DO NOT CHANGE TYPE OR SIZE OF PROPELLER WITHOUT CONSULTING YOUR COBALT DEALER! TAINLESS TEEL Some Cobalts are standard equipped with stainless propellers. In this instance, do not substitute aluminum propellers. Adverse handling and top speed characteristics may be experienced.
Page 48
ODEL PECIFIC NFORMATION ’ APTAIN HAIR DJUSTMENT AND PERATION Your captain’s chairs have the flip-up position for greater visibility and maneuverability while docking. You can sit on the raised cushion or stand in front of the cushion. Standing while driving your boat should only be done while maneuvering at an idle by an experienced driver.
Page 49
Authorized Cobalt Dealer. 12. Horn Button - The horn, itself, is located under the deck. 13. Dimmer Switch - Your Cobalt is equipped with a dimmer switch which controls the intensity of the dash lights including the compass light.
Page 50
Others are beyond human control. INCORRECT PROPELLER APPLICATION CAN CAUSE ADVERSE HANDLING CHARACTERISTICS. DO NOT CHANGE TYPE OR SIZE OF PROPELLER WITHOUT CONSULTING YOUR COBALT DEALER! TAINLESS TEEL Some Cobalts are standard equipped with stainless propellers. In this instance, do not substitute aluminum propellers.
Page 54
ODEL PECIFIC NFORMATION ’ APTAIN HAIR DJUSTMENT AND PERATION Your captain’s chairs have the flip-up position for greater visibility and maneuverability while docking. You can sit on the raised cushion or stand in front of the cushion. Standing while driving your boat should only be done while maneuvering at an idle by an experienced driver.
Page 55
Authorized Cobalt Dealer. 12. Horn Button - The horn, itself, is located under the deck. 13. Dimmer Switch - Your Cobalt is equipped with a dimmer switch which controls the intensity of the dash lights including the compass light.
Page 56
Others are beyond human control. INCORRECT PROPELLER APPLICATION CAN CAUSE ADVERSE HANDLING CHARACTERISTICS. DO NOT CHANGE TYPE OR SIZE OF PROPELLER WITHOUT CONSULTING YOUR COBALT DEALER! TAINLESS TEEL Some Cobalts are standard equipped with stainless propellers. In this instance, do not substitute aluminum propellers.
Page 60
ODEL PECIFIC NFORMATION ’ APTAIN HAIR DJUSTMENT AND PERATION Your captain’s chairs have the flip-up position for greater visibility and maneuverability while docking. You can sit on the raised cushion or stand in front of the cushion. Standing while driving your boat should only be done while maneuvering at an idle by an experienced driver.
Page 61
Authorized Cobalt Dealer. 12. Horn Button - The horn is located under the deck. 13. Dimmer Switch - Your Cobalt is equipped with a dimmer switch which controls the intensity of the dash lights including the compass light.
Page 62
Others are beyond human control. INCORRECT PROPELLER APPLICATION CAN CAUSE ADVERSE HANDLING CHARACTERISTICS. DO NOT CHANGE TYPE OR SIZE OF PROPELLER WITHOUT CONSULTING YOUR COBALT DEALER! TAINLESS TEEL Some Cobalts are standard equipped with stainless propellers. In this instance, do not substitute aluminum propellers.
Page 66
1. Fuel Gauge - shows approximate amount of fuel remaining in tank. 2. Speedometer (Miles Per Hour) 3. Compass - Your Cobalt is equipped with a Faria Compass. The sensor is located in the ski storage area and is adjustable.
Page 67
Authorized Cobalt Dealer. 15. Horn Button - The horn, itself, is located under the deck. 16. Dimmer Switch - Your Cobalt is equipped with a dimmer switch which controls the intensity of the dash lights including the compass light.
Page 68
Others are beyond human control. INCORRECT PROPELLER APPLICATION CAN CAUSE ADVERSE HANDLING CHARACTERISTICS. DO NOT CHANGE TYPE OR SIZE OF PROPELLER WITHOUT CONSULTING YOUR COBALT DEALER! TAINLESS TEEL Some Cobalts are standard equipped with stainless propellers. In this instance, do not substitute aluminum propellers.
Page 69
ODEL PECIFIC NFORMATION ULLING OWER If you need extra pulling power, you can obtain this by decreasing the pitch of your propeller(s) by two degrees. This will not endanger the engine or drive unit as long as the manufacturer’s recommended top RPM’s are not exceeded. ROPELLER PPLICATION HART...
Page 72
ODEL PECIFIC NFORMATION ’ APTAIN HAIR DJUSTMENT AND PERATION Your captain’s chairs have the flip-up position for greater visibility and maneuverability while docking. You can sit on the raised cushion or stand in front of the cushion. Standing while driving your boat should only be done while maneuvering at an idle by an experienced driver.
Page 73
Authorized Cobalt Dealer. 12. Horn Button - The horn is located under the deck. 13. Dimmer Switch - Your Cobalt is equipped with a dimmer switch which controls the intensity of the dash lights including the compass light.
Others are beyond human control. INCORRECT PROPELLER APPLICATION CAN CAUSE ADVERSE HANDLING CHARACTERISTICS. DO NOT CHANGE TYPE OR SIZE OF PROPELLER WITHOUT CONSULTING YOUR COBALT DEALER! TAINLESS TEEL Some Cobalts are standard equipped with stainless propellers. In this instance, do not substitute aluminum propellers.
Page 78
1. Fuel Gauge - shows approximate amount of fuel remaining in tank.. 2. Speedometer (Miles Per Hour) 3. Compass - Your Cobalt is equipped with a Faria Compass. The sensor is located in the ski storage locker and is adjustable.
Page 79
Authorized Cobalt Dealer. 15. Horn Button - The horn, itself, is located under the deck. 16. Dimmer Switch - Your Cobalt is equipped with a dimmer switch which controls the intensity of the dash lights including the compass light.
Page 80
Others are beyond human control. INCORRECT PROPELLER APPLICATION CAN CAUSE ADVERSE HANDLING CHARACTERISTICS. DO NOT CHANGE TYPE OR SIZE OF PROPELLER WITHOUT CONSULTING YOUR COBALT DEALER! TAINLESS TEEL Some Cobalts are standard equipped with stainless propellers. In this instance, do not substitute aluminum propellers.
Page 81
ODEL PECIFIC NFORMATION ULLING OWER If you need extra pulling power, you can obtain this by decreasing the pitch of your propeller(s) by two degrees. This will not endanger the engine or drive unit as long as the manufacturer’s recommended top RPM’s are not exceeded. ROPELLER PPLICATION HART...
Page 84
UNDERWAY. NSTRUMENT ANEL 1. Speedometer (Miles Per Hour) 2. Depth Sounder - Your Cobalt is equipped with a Humminbird Depth Sounder. Included in your owner’s packet are the instructions pertaining to the operation of this unit. Consult your Cobalt Dealer for further information.
Page 85
12. Ignition Key Switch 13. Horn Button - The horn, itself, is located under the deck. 14. Dimmer Switch - Your Cobalt is equipped with a dimmer switch which controls the intensity of the dash lights including the compass light.
Some of these factors are directly correctable by repair or maintenance. Others are beyond human control. INCORRECT PROPELLER APPLICATION CAN CAUSE ADVERSE HANDLING CHARACTERISTICS. DO NOT CHANGE TYPE OR SIZE OF PROPELLER WITHOUT CONSULTING YOUR COBALT DEALER! 253.4 ’ OBALT OATS...
Page 87
ODEL PECIFIC NFORMATION TAINLESS TEEL Some Cobalts are standard equipped with stainless propellers. In this instance, do not substitute aluminum propellers. Adverse handling and top speed characteristics may be experienced. ULLING OWER If you need extra pulling power, you can obtain this by decreasing the pitch of your propeller(s) by two degrees.
Page 90
12 to 14 volts. 3. Speedometer (Miles Per Hour) 4. Compass - Your Cobalt is equipped with a Faria Compass. The sensor is located in the ski storage locker and is adjustable.
Page 91
14. Trim Gauge - Shows the position of the drive unit in reference to the bottom of the boat. 15. Stereo Remote Control 16. Circuit Breakers - Push to reset if necessary. The 262 breaker panel is located under the dash. If the button continues to pop out, consult your Authorized Cobalt Dealer. ELESCOPING OARDING ADDER THIS LADDER MUST ONLY BE USED WHILE ENGINE IS OFF.
• Retract the sunshade and stow by reversing the above operation. THE ARCH WITH SUNSHADE IS DESIGNED FOR FACTORY INSTALLED EQUIPMENT ONLY. ADDITIONAL COMPONENTS CANNOT BE ADDED WITHOUT COBALT AUTHORIZATION. THE ARCH CANNOT BE USED FOR TOWING AND WILL NOT SUPPORT BODY WEIGHT.
Others are beyond human control. INCORRECT PROPELLER APPLICATION CAN CAUSE ADVERSE HANDLING CHARACTERISTICS. DO NOT CHANGE TYPE OR SIZE OF PROPELLER WITHOUT CONSULTING YOUR COBALT DEALER! TAINLESS TEEL Some Cobalts are standard equipped with stainless propellers. In this instance, do not substitute aluminum propellers.
Page 94
ODEL PECIFIC NFORMATION ULLING OWER If you need extra pulling power, you can obtain this by decreasing the pitch of your propeller(s) by two degrees. This will not endanger the engine or drive unit as long as the manufacturer’s recommended top RPM’s are not exceeded. ROPELLER PPLICATION HART...
If this happens, simply pull harder until the seat opens. To prevent this from happening in the future, you can treat the vinyl with any type of vinyl spray that will lubricate the finish. Check with your cobalt dealer for further information.
Page 97
OPERATING. MAKE SURE LIGHTS ARE NOT BLOCKED BY CANVAS OR OTHER OBSTACLES. 10. Circuit Breakers - Push to reset if necessary. If the button continues to pop out, consult your Authorized Cobalt Dealer. 11. 12 VDC Receptacle 12. Horn Button - The horn, itself, is located under the deck.
Page 98
Others are beyond human control. INCORRECT PROPELLER APPLICATION CAN CAUSE ADVERSE HANDLING CHARACTERISTICS. DO NOT CHANGE TYPE OR SIZE OF PROPELLER WITHOUT CONSULTING YOUR COBALT DEALER! TAINLESS TEEL Some Cobalts are standard equipped with stainless propellers. In this instance, do not substitute aluminum propellers.
ODEL PECIFIC INFORMATION ULLING OWER If you need extra pulling power, you can obtain this by decreasing the pitch of your propeller(s) by two degrees. This will not endanger the engine or drive unit as long as the manufacturer’s recommended top RPM’s are not exceeded. ROPELLER PPLICATION HART...
Page 101
ODEL PECIFIC NFORMA TION ODEL PECIFIC NFORMA TION ’ OBALT OATS WNER ANUAL AYOUT AND PECIFICATIONS SPECIFICATIONS Centerline(w/ anc roller) .29’5” 9.1 m Windlass Centerline(w/o anc roller)28’10” 8.8 m (optional) Beam ....9’ 6” 2.89 m Fuel Capacity .
Page 102
ODEL PECIFIC NFORMATION ’ APTAIN HAIR DJUSTMENT AND PERATION Your captain’s chair has the flip-up position for greater visibility and maneuverability while docking. You can sit on the raised cushion or stand in front of the cushion. The chairs are adjustable fore and aft. Fore and Aft Adjustment - A handle on the seat allows the seat to move.
NFORMATION 9. Two Position Switch - Controls equipment Single Engine Instrumentation as labeled. 10. Dimmer Switch - Your Cobalt is equipped with a dimmer switch which controls the intensity of the dash lights including the compass light. 11. Water Temperature Gauge - Indicated outside water temperature.
Page 104
PERATION SINGLE ENGINE Your Cobalt is equipped with a dual battery switch. With this switch off, nothing in the boat will operate with the exception of the automatic bilge pumps. Make sure the switch is in the “1” or “2” position. You can operate the boat with switch in the “both” position but not for extended periods.
OWER PTIONAL When your Cobalt is connected to shore power (110 VAC), any or all of the ship’s electrical systems can be operated. The 30-amp shore power cord must be plugged into the proper shore power receptacle and the boat receptacle located at the swim platform.
ODEL PECIFIC NFORMATION NORMAL OPERATION Panel is located in cockpit storage area under sink. • Press reverse polarity test switch and verify green light comes on, if it does not, consult a qualified technician. • Switch the top double-pole “AC main” breaker on the distribution panel to “on” and then the respective branch circuit breakers below it as needed.
HARGER AND SOLATOR OPTIONAL Your Cobalt is equipped with a charging system. Anytime your boat is connected to shore power with the appropriate switches at the panel energized, the battery charger will operate and keep both batteries fully charged. In addition, the system includes a galvanic isolator system to help prevent corrosion of underwater gear.
Page 108
ODEL PECIFIC NFORMATION OMPRESSOR Your Cobalt is equipped with an inflation device located in the port side, aft storage locker. This is a 12 VDC system and will operate when the ship’s batteries are turned on. INDLASS PTIONAL The Windlass system gets it’s power from the ship’s electrical system (12 VDC) via a control panel located in the starboard side storage compartment of the cockpit next to the battery switches.
PECIFIC NFORMATION INCORRECT PROPELLER APPLICATION CAN CAUSE ADVERSE HANDLING CHARACTERISTICS. DO NOT CHANGE TYPE OR SIZE OF PROPELLER WITHOUT CONSULTING YOUR COBALT DEALER! TAINLESS TEEL Some Cobalts are standard equipped with stainless propellers. In this instance, do not substitute aluminum propellers. Adverse handling and top speed characteristics may be experienced.
Page 111
ODEL PECIFIC NFORMA TION ODEL PECIFIC NFORMA TION ’ OBALT OATS WNER ANUAL AYOUT AND PECIFICATIONS SPECIFICATIONS Centerline(w/ anc roller) .29’5” 9.1 m Centerline(w/o anc roller)28’10” 8.8 m Windlass Beam ....9’ 6” 2.89 m (optional) Fuel Capacity .
Page 112
1. Fuel Gauge - shows approximate amount Single Engine Instrumentation of fuel remaining in tank. 2. Speedometer (Miles Per Hour) 3. Depth Sounder - Your Cobalt is equipped with a Humminbird Depth Sounder. Included in your owner’s packet are the instructions pertaining to the operation of this unit.
Page 113
SHOULD WATER TEMPERATURE REACH 180 DEGREES FAHRENHEIT, YOUR ENGINE IS OVERHEATING AND SHOULD BE CHECKED IMMEDIATELY FOR PROBABLE CAUSE. Twin Engine Instrumentation 11. Dimmer Switch - Your Cobalt is equipped with a dimmer switch which controls the intensity of the dash lights including the compass light.
WITCHES PERATION Single Engine - Your Cobalt is equipped with a dual battery switch. With this switch off, nothing in the boat will operate with the exception of the automatic bilge pumps. Make sure the switch is in the “1” or “2” position. You can operate the boat with switch in the “both”...
OWER OPTIONAL When your Cobalt is connected to shore power (110 VAC), any or all of the ship’s electrical systems can be operated. The two 30-amp shore power cords must be plugged into the proper shore power receptacles and the boat receptacles located in the aft storage compartment.
ODEL PECIFIC NFORMATION HORE OWER ISTRIBUTION ANEL OPTIONAL THIS IS A SUMMARY ONLY AND DOES NOT EXPLAIN ALL OPERATION. BEFORE OPERATING THESE SYSTEMS, READ THE OWNERS MANUALS PROVIDED FOR EACH DEVICE. CONSULT QUALIFIED PERSONNEL IF YOU HAVE QUESTIONS. GENERAL FUNCTION The AC portion of distribution panel (black Marinetics panel #500472) receives AC power from the shore power cable, generator or inverter and distributes it through a double-pole main circuit breaker which in turn supplies the individual branch circuit...
ODEL PECIFIC NFORMATION ENERATOR OPTIONAL THIS IS A SUMMARY ONLY AND DOES NOT EXPLAIN ALL OPERATION. BEFORE OPERATING THESE SYSTEMS, READ THE OWNERS MANUALS PROVIDED FOR EACH DEVICE. CONSULT QUALIFIED PERSONNEL IF YOU HAVE QUESTIONS. The generator is located in the cockpit floor storage area with a control panel at the helm and source selector switch at the Cabin Distribution Panel.
ATER YSTEM Your Cobalt is equipped with a 31-gallon capacity water system (37-gallons including hot water heater). The system is operated by a 12 VDC water pump located in the engine compartment. It is necessary for the ship’s batteries to be turned on and the 293.8...
Your Cobalt maybe equipped with a six-gallon hot water heater. This unit operates in two modes. If your Cobalt is connected to shore power (110 VAC) simply energize the appropriate switches at the cabin control panel to turn on the 110 volt power and the switch marked “water heater”.
Page 120
YSTEM OPTIONAL The GPS system in your Cobalt performs many functions. The system can precisely tell you your location, form a trip record, a speed log, and many other functions. In addition, individual mapping chips can be purchased through your Cobalt dealer for most lakes, rivers, and coastal areas of the United States and Canada.
Others are beyond human control. INCORRECT PROPELLER APPLICATION CAN CAUSE ADVERSE HANDLING CHARACTERISTICS. DO NOT CHANGE TYPE OR SIZE OF PROPELLER WITHOUT CONSULTING YOUR COBALT DEALER! TAINLESS TEEL Some Cobalts are standard equipped with stainless propellers. In this instance, do not substitute aluminum propellers.
Page 124
12 to 14 volts. 4. Speedometer (Miles Per Hour) 5. Compass - Your Cobalt may be optionally equipped with a Faria Compass. The sensor is located in the ski storage locker and is adjustable.
Page 125
Consult your Cobalt Dealer for further information. 16. 12 VDC Receptacle 17. Dimmer Switch - Your Cobalt may be equipped with a dimmer switch which controls the intensity of the dash lights including the compass light. 18. Circuit Breakers - Push to reset if necessary. If the button continues to pop out, consult your Authorized Cobalt Dealer.
Page 126
ATER YSTEM Your Cobalt is equipped with a 10-gallon capacity water system. The system is operated by a 12 VDC water pump located in the engine compartment. It is necessary for the ship’s batteries to be turned on for the water system to operate. Consult your Cobalt Dealer for winterization requirements.
Need help?
Do you have a question about the 2000 and is the answer not in the manual?
Questions and answers