F8.5: Control Change On/Off; F8.6: Midi Transmit Transpose; F8.7: Panel/Status Transmit; F8.8: Bulk Data Dump - Yamaha Clavinova CLP-555 Owner's Manual

The Function Mode

F8.5: Control Change ON/OFF

nal MIDI device or keyboard, causing the voice on the corresponding channel to be affected
by pedal and other "control" settings received from the controlling device (the keyboard voice
is not affected, but reverb depth data will affect the Clavinova settings). The Clavinova also
transmits MIDI control change information when one of its pedals or other appropriate con-
trols are operated.
that, for example, the Clavinova pedals and other controls can be operated without affecting an
external MIDI device.
"On" or "OFF".

F8.6: MIDI Transmit Transpose

or down in semitone increments by up to plus or minus 12 semitones. The pitch of th-
Clavinova itself is not affected
tion. The range is from "–12" (down one octave) through "0" (no transposition) to "12" (u
one octave)

F8.7: Panel/Status Transmit

transmitted via the MIDI OUT terminal. This is particularly useful if you will be recording
performances to a MIDI sequence recorder such as the Yamaha DOU-10 Disk Orchestra Unit
which will be used to control the Clavinova on playback. By transmitting the Clavinova panel
settings and recording them on the MIDI sequence recorder prior to the actual performance
data, the Clavinova will be automatically restored to the same settings when the performance
is played back.
display when the data has been successfully transmitted.

F8.8: Bulk Data Dump

storage device such as the Yamaha DOU-10 Disk Orchestra Unit, other sequence recorders, or
MIDI compatible computers.
display when the data has been successfully transmitted.
30 ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
Normally the Clavinova will respond to MIDI control change data received from an exter-
This function makes it possible to cancel control change data reception and transmission so
Use the [–/NO] and [+/YES] buttons to turn control change transmission and reception
Press the [–/NO] and [+/YES] buttons simultaneously to recall the default setting: "On".
This function allows the MIDI note data transmitted by the Clavinova to be transposed up
Use the [–/NO] and [+/YES] buttons to set the desired amount of MIDI transmit transposi-
Press the [–/NO] and [+/YES] buttons simultaneously to recall the default setting: "0"
This function causes all the current Clavinova control settings (selected voice, etc.) to be
Press the [+/YES] button to transmit the panel/status data. "End" will appear on the LED
• See page 36 for list of the "Panel Data Contents" transmitted by this function.
• Panel setting data can only be transferred between the same models (data cannot, for example, be
transferred between a CLP-555 and CLP-411).
This function is used to transmit all data stored in the Recorder memory to a MIDI data
Press the [+/YES] button to begin bulk transmission. "End" will appear on the LED
• Bulk dump will not function when the recorder is in operation.
• Recorder data can only be transferred between the same models (data cannot, for example, be
transferred between a CLP-555 and CLP-411).
• No MIDI note/panel data transmission or data reception occurs during a bulk dump transmit operation.
......................................................................................................
......................................................................................................
.............................................................................................................
............................................................................................................................