Panasonic ES‑LV61 Operating Instructions page 2

Reading the LCD panel when charging
The LCD panel shows the remaining battery capacity from 0% to
100%, in 10% increments.
While charging After charging is completed
Battery capacity and Charge status
The indicators glow. will light up and then turn off after 5
seconds.
•
After charging is completed, turning the power switch ON with
the shaver plugged in will cause Battery capacity and Charge
status to light up and then turn off after 5 seconds. This shows
that the shaver is fully charged.
• Recommended ambient temperature for charging is 5‑35 °C. The
battery may not charge properly or at all under extreme low or
high temperatures.
The indicators on the LCD panel blink when there is a problem
with charging.
• When charging the shaver for the first time or when it has not
been in use for more than 6 months, the indicators on the LCD
panel may not glow. It will eventually glow if kept connected.
5. Remove the outer foil section and press the
5
power switch for more than 2 seconds to
activate the sonic vibration cleaning mode
and clean it with running water.
6. Wipe off any drops of water with a dry cloth.
7. Dry the outer foil section and the shaver
completely.
8. Attach the outer foil section to the shaver.
9. Lubricate the shaver.
7
Lubrication
To maintain shaving comfort for a long time, it is recommended
that the oil provided with the shaver is used.
1. Switch off the shaver.
2. Apply one drop of oil to each of the outer foils.
3. Raise the trimmer and apply a drop of oil.
4. Switch the shaver on, and run it for approximately
five seconds.
5. Switch off the shaver, and wipe off any excess oil
from the outer foils with a soft cloth.
ES-LV61_AUS.indb 2
Shave
Using the shaver
1 2
1 2
Rotate the lock ring to Hold the shaver
unlock the power switch as illustrated
and press the power above and shave.
switch.
Page 3
•
We recommend using the shaver in an ambient temperature
range of 5 ‑ 35 °C. If used outside this range, the appliance may
stop operating.
Start out shaving by applying gentle pressure to your face.
Stretch your skin with your free hand and move the shaver back
and forth in the direction of your beard. You may gently increase
the amount of pressure as your skin becomes accustomed to
this shaver. Applying excessive pressure does not provide a
closer shave.
Caution
• If you press the power switch for more than 2 seconds, the
Page 5
sonic vibration cleaning mode is activated.
You cannot shave in this mode.
•
Do not place your fingers on the power switch while using the
shaver. This may cause the shaver to turn off or enter the sonic
vibration cleaning mode. Place your fingers on the finger rest
while using the shaver.
4
Cleaning with the brush
Clean the inner blades using the
short brush by moving it in direction
(A).
Clean the system outer foil, the
shaver body and the trimmer using
the long brush.
•
Do not move the short brush in
(A) (B)
direction (B) as it will damage the
inner blades and affect their
sharpness.
• Do not use the short brush to
clean the outer foils.
Replacing the system outer foil and the inner blades
system outer foil once every year
inner blades once every two years
Replacing the system outer foil

1. Press the foil frame release buttons and lift
1
the outer foil section upwards.
2. Press the system outer foil release buttons
and pull down the system outer foil.
3. Align the foil frame mark ( ) and the
system outer foil mark ( ) and securely
attach together.
• The system outer foil cannot be reversely
attached.
2
•
Always insert the system outer foil to the
foil frame when attaching to the shaver.
4. After turning the foil frame mark
( ) to the front, securely attach the
outer foil section to the shaver until it clicks.
6
Using the trimmer
You can change the pivot action. Slide the handle up to "
when using the trimmer.
FREE
You can move the shaver head.
LOCK
You can lock the shaver head.
Slide the trimmer handle up. Place at a right
angle to your skin and move downwards to
trim your sideburns.
Reading the LCD panel when using
During use
The used time is shown.
• The indicators turn off after
remaining battery capacity are
5 seconds.
shown alternately after turning
•
The shown time returns to
[0'00"] after 10 minutes.
Replacing the inner blades

1. Press the foil frame release buttons and lift
the outer foil section upwards.
2. Remove the inner blades one at a time.
• Do not touch the edges (metal parts) of
the inner blades to prevent injury to your
hand.
3. Insert the inner blades one at a time until
they click.
Replacement parts

Replacement parts are available at your dealer or Service Center.
Replacement parts for System outer foil and
ES‑LV61 inner blades
System outer foil
Inner blades
Removing the built‑in rechargeable battery
Remove the built‑in rechargeable battery before disposing of the
shaver. Please make sure that the battery is disposed of at an
officially designated location if there is one. Do not dismantle or
3
replace the battery so that you can use the shaver again. This
could cause fire or an electric shock.
Please contact an authorised service center.
•
Disconnect the power cord from the shaver when removing the
battery.
When the battery capacity is low
"
• You can shave 1 to 2 times after "10%"
appears.
(This will differ depending on usage.)
"10%" appears and
• A full charge will supply enough power for approx. 14 shaves of
3 minutes each. (This will differ depending on usage.)
Clean
Cleaning the shaver
We recommend that you clean your shaver with the the sonic
vibration cleaning mode when the faucet symbol
the LCD panel.
1. Disconnect the power cord from the shaver.
2. Apply some hand soap and some water to
the outer foil.
3. Rotate the lock ring to unlock the power
switch.
4. Press the power switch for more than 2
seconds to activate the sonic vibration
cleaning mode.
• appears on the LCD panel.
After use
• After about 20 seconds, it will be
automatically turned off, or you can turn it
off by pressing the power switch.
The used time and the
off the shaver.
5
•
Perform steps 1 to 4 and lift the battery, and then remove it.
1
2 3
For environmental protection and recycling of materials
This shaver contains a Lithium‑ion battery.
Please make sure that the battery is disposed of at an officially
assigned location, if there is one in your country.
Specifications
WES9030
WES9171
See the name plate on the AC adaptor.
Power source
WES9170
(Automatic voltage conversion)
Motor voltage
3.6 V
Charging time Approx. 1 hour
This product is intended for household use only.
7
blinks.
appears on
4




2011/02/28 17:14:11